ANGLE GRINDER PWS 125 A1
WINKELSCHLEIFER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
ANGLE GRINDER
Operation and Safety Notes
Translation of original operation manual
ΓΩΝΙΑΚΟΣ ΤΡΟΧΟΣ
Υποδείξεις χειρισμού και ασφαλείας
Μετάφραση των αυθεντικών οδηγιών λειτουργίας
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
device.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τις δυο σελίδες με τις εικόνες και εξοικειωθείτε με όλες τις
λειτουργίες της συσκευής.
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.
GB / IE / CY Operation and Safety Notes Page 5
GR / CY Υποδείξεις χειρισμού και ασφαλείας Σελίδα 19
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 35
A B
9
2
5
6
7
8
C D
6
11
1
3
4
10
E
F
G
5 GB/IE/CY
Table of contents
Introduction
Proper use ......................................................................................................................Page 6
Features and equipment ...............................................................................................Page 6
Included items ...............................................................................................................Page 7
Technical information ....................................................................................................Page 7
General safety advice for electrical power tools
1. Workplace safety .....................................................................................................Page 7
2.
Electrical safety .........................................................................................................Page 7
3. Personal safety ..........................................................................................................Page 8
4.
Careful handling and use of electrical power tools ...............................................Page 8
Safety advice for all uses ..............................................................................................Page 9
Safety advice relating to kickback ...............................................................................Page 10
Special safety advice relating to grinding and disc-cutting ........................................Page 11
Further special safety advice for disc-cutting ...............................................................Page 11
Special safety advice for abrading using sandpaper ................................................Page 12
Special safety advice for polishing ..............................................................................Page 12
Special safety advice for working with wire brushes ..................................................Page 12
Safety advice for angle grinders ..................................................................................Page 12
Advice on use ................................................................................................................Page 13
Use
Switching on and off .....................................................................................................Page 14
Setting the speed ...........................................................................................................Page 14
Changing a disc ............................................................................................................Page 15
Use of accessories
Cutting / roughing discs ................................................................................................Page 15
Flap discs for metal .......................................................................................................Page 15
Other accessories .........................................................................................................Page 16
Adjusting the disc guard cover .....................................................................................Page 16
Using the auxiliary handle ............................................................................................Page 17
Maintenance and cleaning .........................................................................Page 17
Service .........................................................................................................................Page 17
Warranty ................................................................................................................... Page 17
Disposal ......................................................................................................................Page 18
Declaration of Conformity / Manufacturer..................................Page 18
6 GB/IE/CY
Introduction
Angle grinder PWS 125 A1
Grinding, roughing, cutting
Introduction
Please make sure you familiarise your-
self fully with the way the device works
before you use it for the first time and
that you understand how to handle electrical pow-
er tools correctly. To help you do this please read
the accompanying operating instructions. Keep
these instructions in a safe place. If you pass the
device on to anyone else, please ensure that you
also pass on all the documentation.
Proper use
The device is intended for the dry cutting, rough
grinding and brushing of metal and stone. Any other
use or modification to the device shall be considered
as improper use and could give rise to considerable
dangers. We will not accept liability for loss or
damage arising from improper use. The device is
not intended for commercial use.
Note: Slots cut in load-bearing walls must comply
with standard DIN 1053 Part 1 or the regulations
applicable in your country.
These instructions and advice must be observed.
Before you start a task, seek the advice of a com-
petent structural engineer, architect, or the relevant
site management staff.
Features and equipment
1
Safety lock-out
2
ON / OFF switch
3
Carbon brushes cover
4
Auxiliary handle
5
Adjustable disc guard
6
Clamping nut
7
Mounting spindle
8
Mounting flange
9
Spindle lock button
10
Speed pre-selector wheel
11
Spanner (Fig. B)
The following pictograms are used in these operating instructions / on the device:
Read instruction manual!
n
0
Rated idle running speed
Observe caution and safety notes! Safety class II
Caution – electric shock!
Danger to life!
Proper procedure and handling.
Risk of explosion!
Wear hearing protection, dust
protection mask, protective glasses
and protective gloves.
Risk of fire!
Keep children away from electrical
power tools!
V
~
Volt (AC)
Risk of loss of life by electric shock
from damaged mains lead or mains
plug!
W
Watts (effective power)
Dispose packaging and appliance in
an environmentally-friendly way!
7 GB/IE/CY
Introduction / General safety advice for electrical power tools
Included items
1 Angle grinder PWS 125 A1
1 Metal-cutting disc
1 Auxiliary handle
1 Disc guard cover
1 Spanner
1 Operating instructions
Technical information
Rated input: 1200 W
Rated voltage: 230 V∼, 50 Hz
Design no-load speed: n
0
3000–11000 min
-1
Spindle thread: M14
Protection class: II /
Noise and vibration data:
Measured values for noise are determined in ac-
cordance with EN 60745. The A-weighted noise
level of the electrical power tool are typically:
Sound pressure level: 91 dB(A)
Sound power level: 102 dB(A)
Uncertainty K: 3 dB
Wear hearing protection!
Vibration total values determined
according to EN 60745:
Surface grinding:
Vibration emission value a
h
= 13.431 m/s
2
,
Uncertainty K = 1.5 m/s
2
.
The vibration level given in these
instructions has been measured in accordance with
a standardised measurement procedure specified in
EN 60745 and can be used to compare devices.
Different uses of the device give rise to different
vibration levels and in many cases they may exceed
the values given in these instructions. It is easy to
underestimate the vibration load if the electrical pow-
er tool is used regularly in particular circumstances.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
General safety advice for
electrical power tools
Read all the safety advice
and instructions! Failure to observe the safety
advice and instructions may result in electric shock,
fire and / or serious injury.
Keep all the safety advice and instructions
in a safe place for future reference!
The term “electrical tool” used in the safety advice
refers to electrical tools powered by mains electrici-
ty (by means of a mains lead) and electrical tools
powered by rechargeable batteries (without a
mains lead).
1.
Workplace safety
a) Keep your working area clean and
well lit. Untidy or poorly lit working areas
can lead to accidents.
b)
Do not work with the device
in potentially explosive envi-
ronments in which there are
inflammable liquids, gases or dusts.
Electrical power tools create sparks, which can
ignite dusts or fumes.
c)
Keep children and other
people away while you are
operating the electrical tool.
Distractions can cause you to lose control of
the device.
2.
Electrical safety
a)
The mains plug on the device must match
the mains socket. The plug must not be
modified in any way. Do not use an
adapter plug with devices fitted with
8 GB/IE/CY
a protective earth. Unmodified plugs and
matching sockets reduce the risk of electric shock.
b) Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrig-
erators with any part of your body.
There is an increased risk of electric shock if
your body is earthed
.
c) Keep the device away from rain or
moisture. Water entering an electrical device
increases the risk of electric shock.
d)
Do not use the mains lead for
any purpose for which it was
not intended, e.g. to carry the
device, to hang up the device or to pull
the mains plug out of the mains socket.
Keep the mains lead away from heat,
oil, sharp edges or moving parts of the
device. Damaged or tangled mains leads
increase the risk of electric shock.
e) When working outdoors with an elec-
trical power tool always use extension
cables that are also approved for use
outdoors. The use of an extension cable suita
ble
for outdoor use reduces the risk of electric shock.
f) Use a residual current device (RCD)
for protection if operating the electri-
cal power tool in a moist environment
is unavoidable. The use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Remain alert at all times, watch what
you are doing and always proceed
with caution. Do not use the device if
you are tired or under the influence of
drugs, alcohol or medication. One mo
ment
of carelessness when using the device can lead
to serious injury.
b)
Wear personal protective
equipment and always wear
safety glasses. The wearing of
personal protective equipment such as dust
masks, non-slip safety shoes, safety helmets or
ear protectors, appropriate to the type of elec-
trical power tool used and work undertaken,
reduces the risk of injury.
c) Avoid unintentional operation of the
device. Check that the electrical power
tool is switched off before you connect
it to the mains, pick it up or carry it.
Accidents can happen if you carry the device
with your finger on the ON / OFF switch or with
the device switched on.
d) Remove any setting tools or spanners
before you switch the device on. A tool
or spanner left attached to a rotating part of a
device can lead to injury.
e) Avoid placing your body in an unnat-
ural position. Keep proper footing
and balance at all times. By doing this
you will be in a better position to control the
device in unforeseen circumstances.
f) Wear suitable clothing. Do not wear
loose clothing or jewellery. Keep your
hair, clothing and gloves clear of mov-
ing parts. Loose clothing, jewellery or long
hair can become trapped in moving parts.
g) If vacuum dust extraction and collection
devices are fitted do not forget to
check
that they are properly connected and
correctly used. The use of these devices
reduces the hazard presented by dust.
4.
Careful handling and use
of electrical power tools
a) Do not overload the device. Always
use an electrical power tool that is
intended for the task you are under-
taking. By using the right electrical power
tool for the job you will work more safely and
achieve a better result.
b) Do not use an electrical power tool if
its switch is defective. An electrical power
tool that can no longer be switched on and off
is dangerous and must be repaired.
c) Pull the mains plug from the socket
before you make any adjustments to
the device, change accessories or when
the device is put away. This precaution is
intended to prevent you from unintentionally
starting the device.
General safety advice for electrical power tools
9 GB/IE/CY
d) When not in use always ensure that
electrical power tools are kept out of
reach of children. Do not let anyone use
the device if he or she is not familiar
with it or has not read the instructions
and advice. Electrical power tools are dan-
gerous when they are used by inexperienced
people.
e)
Look after the device carefully. Check
that moving parts are working prop-
erly and move freely. Check for any
parts that are broken or damaged
enough to detrimentally affect the
functioning of the device. Have dam-
aged parts repaired before you use
the device. Many accidents have their origins
in poorly maintained electrical power tools.
f) Keep cutting tools clean and sharp.
Carefully maintained cutting tools with sharp
cutting edges are less likely to jam and are
easier to control.
g) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice, and
the stipulations drawn up for this par-
ticular type of device. In doing this, take
into account the working conditions
and the task in hand. The use of electrical
power tools for purposes other than those in-
tended can lead to dangerous situations.
Safety advice for all uses
General safety advice for grinding,
sanding (with sandpaper), wire brushing,
polishing and disc-cutting:
a) This electrical power tool is intended
for use as a grinding, sanding, wire-
brushing, and disc-cutting machine.
Observe all the safety advice, instruc-
tions, information in figures and all
other information you received with
this device. If you do not observe the following
advice it could lead to electric shock, fire and /
or serious injury.
b) Normative statement / advice for this tool is not
applicable.
c) Do not use any accessory not specifi-
cally intended by the manufacturer
for this electrical power tool. Although
an accessory may fit on your electrical power
tool, this does not on its own guarantee that it
can be safely used.
d) The maximum permitted speed of an
attachment must be at least as high as
the maximum speed indicated for the
electrical power tool. An accessory rotating
faster than its permitted speed could disintegrate
or fly off.
e) The external diameter and the thickness
of the attachment must be compatible
with the dimensions of your electrical
power tool. Attachments that are not dimen-
sionally compatible cannot be adequately
guarded or controlled.
f) Grinding discs, flanges, grinding
wheels or other accessories must fit
exactly on to the spindle of your elec-
trical power tool. Attachments that do not
exactly fit on the spindle turn unevenly, vibrate
severely and could lead to loss of control.
g) Do not use damaged attachments.
Before every use check attachments
such as grinding discs for loose frag-
ments and cracks, grinding wheels for
cracks, deterioration or excessive
wear and wire brushes for loose or
broken wires. If the electrical power
tool or attachment is dropped, inspect
for damage or change the attachment
for an undamaged one. When you
have inspected and inserted the at-
tachment, position yourself and by-
standers away from the plane of the
rotating attachment and run the device
at maximum speed for one minute.
Damaged attachments will usually break apart
during this test.
h)
Wear personal protective
equipment. Use a full face vi-
sor, safety goggles or safety
glasses, depending on the application.
Wear a dust mask, hearing protectors,
General safety advice for electrical power tools
10 GB/IE/CY
safety gloves or special apron capable
of stopping particles of the grinding
medium or workpiece, as appropriate
for the task. Eyes must be protected from
the flying debris which can arise from some
operations. Dust or breathing masks must be
capable of filtering out the dust generated by
the application. Prolonged exposure to loud
noise can lead to hearing loss.
i) Keep bystanders at a safe distance
from your work area. Anyone entering
the work area must wear personal
protective equipment. Fragments of the
workpiece or of a broken attachment could fly
off and cause injury beyond the immediate
working area.
j) Hold the device by the insulated han-
dle surfaces when you are undertak-
ing work where there is the danger
of the attachment striking hidden
electricity cables or the device’s mains
lead. Contact with a live wire could cause
metal parts of the device to become live and
lead to electric shock.
k) Keep the mains lead away from rotat-
ing attachments. If you lose control of the
device the mains lead may become severed or
trapped and your hand or arm may be pulled
into the rotating attachment.
l) Never lay the electrical power tool
down until after the attachment has
come to a complete standstill. The rotat-
ing attachment may snag when it comes into
contact with the surface and cause you to lose
control of the device.
m) Do not have the electrical power tool
running while you are carrying it. Your
clothing could become trapped by unintention-
al contact with the rotating attachment and the
tool could be pulled into your body.
n) Clean the ventilation slots on your
electrical power tool regularly. The mo-
tor’s fan draws dust into the housing. A build-up
of metal dust could give rise to an electrical
hazard.
o)
Never use the electrical
power tool near inflammable
materials. Sparks could ignite
these materials.
p) Do not use attachments that require
the use of coolants. The use of water or
other liquid coolants could result in electric shock.
Safety advice
relating to kickback
Kickback is the sudden reaction to a pinched or
snagged rotating attachment, such as a grinding
disc, grinding pad, wire brush etc. Pinching or
snagging results in the rotating attachment coming
to an abrupt stop. This causes the electrical power
tool (if not controlled) to move in the opposite di-
rection to the direction of rotation of the attachment
at the point of constraint.
If, for example, a grinding disc is pinched or snags
in a workpiece, this can cause the edge of the
grinding disc to penetrate the workpiece, become
trapped there and either free itself or kickback. The
grinding disc moves towards or away from the op-
erator, depending on the direction of movement of
the disc at the point of constraint. The grinding disc
could also break.
Kickback occurs as a result of incorrect use or mis-
use of the electrical power tool. It can be prevented
by taking the appropriate precautions as described
below.
a) Maintain a firm grip on the electrical
power tool and position your body
and arms to allow you to resist kick-
back forces. Always use the auxiliary
handle, if provided, to exercise the
greatest possible control over kick-
back forces or reaction torques as the
device builds up to full speed. By taking
suitable precautions the operator can control
kickback and reaction forces.
b) Do not place your hands near a rotat-
ing attachment. If kickback occurs the at-
tachment could move over your hand.
General safety advice for electrical power tools
11 GB/IE/CY
c) Avoid positioning your body in the
area into which the electrical power
tool would move in the event of a
kickback. A kickback moves the electrical
power tool in the opposite direction to the di-
rection of movement of the grinding disc at the
point of constraint.
d) Work particularly carefully in the
area of corners, sharp edges etc. to
avoid the attachment bouncing or
snagging on the workpiece. Corners,
sharp edges or bouncing have a tendency to
snag the rotating attachment. This causes loss
of control or kickback.
e) Do not use saw-chain woodcarving
discs or toothed discs. Such attachments
create frequent kickback and loss of control of
the electrical power tool.
Special safety advice relating
to grinding and disc-cutting
a) Always use the guard designed for
the type of abrasive consumable you
are using. Always use abrasive consumables
approved for use with your electrical power
tool. Abrasive consumables not approved for
use with your electrical power tool cannot be
adequately guarded and are unsafe.
b) To ensure the highest level of opera-
tional safety, the disc guard cover must
be attached to the electrical power tool
and set in such a way that the smallest
possible area of the abrasive consum-
able is exposed to the operator. The disc
guard cover is there to protect the operator from
pieces breaking off and accidental contact with
the abrasive consumable.
c) Abrasive consumables must be used
only for their recommended purpos-
es, For example: never grind with the
side face of a cutting disc. Cutting discs
are intended for removing material using the
edge of the disc. Sideways forces on these
abrasive consumables can cause them to break.
d) Always use an undamaged mounting
flange of the correct size and shape
for your selected grinding disc. Suitable
flanges support the grinding disc and reduce the
chance of it breaking. Flanges for cutting discs
are
different from the flanges for other abrasive discs.
e) Never use worn down abrasive con-
sumables intended for larger electrical
power tools. Abrasive consumables intended
for larger electrical power tools are not designed
for the faster rotational speeds of these smaller
electrical power tools and could break.
Further special safety
advice for disc-cutting
a) Avoid snagging the cutting disc and
do not use too much contact pressure.
Do not attempt to make excessively
deep cuts. Overloading the cutting disc in-
creases the load and the tendency of the disc
to twist or snag in the cut, making kickback or
disc breakage more likely.
b) Avoid the area in front of or behind
the rotating cutting disc. If the cutting disc
is moving away from you at the point of con-
straint in the workpiece, then, in the event of
a kickback, the electrical power tool and the
rotating disc may be thrown towards you.
c) If the cutting disc jams or you stop
work for a while, switch the device
off and hold it until the disc comes to
a complete stop. Never attempt to
pull the still rotating cutting disc out of
the cut as this could cause kickback.
Determine and rectify the reason for the jamming.
d) Do not switch on the device if the cut-
ting disc is in the workpiece. Allow
the cutting disc to reach full speed be-
fore carefully continuing with the cut.
Otherwise the disc could snag, jump out of the
workpiece or cause a kickback.
e) Support boards or workpieces whilst
cutting to reduce the risk of kickback
caused by a jammed cutting disc. Large
workpieces may bend under their own weight.
The workpiece must be supported to both sides
of the cutting disc and particularly near the
cutting disc and at the workpiece edge.
General safety advice for electrical power tools
12 GB/IE/CY
f) B
e particularly careful when pocket
cutting in existing walls or other areas
where you cannot see what you are cut-
t
ing into. The cutting disc plunged into the surface
could cut through gas or water pipes, electricity
cables or other objects and cause kickback.
Special safety advice for
abrading using sandpaper
Do not use over-sized sanding sheets.
Follow the manufacturer’s recommen-
dations for sanding sheet size. Sanding
sheets that project beyond the backing pad
could cause injury in addition to jamming,
tearing of the sheet or kickback.
Special safety
advice for polishing
Do not use the polishing bonnet if it
has any loose parts, in particular the
fastening cords. Tuck the fastening cords
away or trim them. Loose fastening cords rotat-
ing with the attachment could catch your fingers
or become trapped in the workpiece.
Special safety advice for
working with wire brushes
a) Bear in mind that wire brushes lose
pieces of wire during normal use. Do
not overload the wires by applying too
much pressure. Flying pieces of wire can very
easily penetrate thin clothing and / or skin.
b) U
se a guard, if recommended, but m
ake
sure that the wire brush does not come
into contact with the guard. The diameters
of disc brushes and cup brushes can increase
due to contact pressure and centripetal forces.
Safety advice
for angle grinders
DANGER OF ELECTRIC SHOCK! Do not
operate the device if the mains lead
or mains plug is damaged.
DANGER OF ELECTRIC SHOCK! Do not
touch the mains lead if it becomes
damaged or cut through while you
are using the device. Pull the plug out of
the mains socket immediately and have the de-
vice repaired by a suitably qualified person or
at your service centre.
DANGER OF ELECTRIC SHOCK! Do not
operate the device if it is damp and
do not use it in a damp environment.
DANGER OF ELECTRIC SHOCK! If you
use the device outdoors, always con
nect
it through a residual current device
(RCD) with a maximum trip current of
30 mA. If using an extension lead, always use
one that is approved for outdoor use.
Do not suspend or carry the device by
the mains lead. Always work with the
mains lead leading away from the
rear of the device. Otherwise the device
could be damaged.
Grinding discs must be carefully kept
and handled in accordance with the
manufacturer’s instructions. Otherwise
they could be damaged.
Make sure that abrasive consumables
and tools are attached in accordance
with the manufacturer’s instructions
and advice. Otherwise they could become
detached from the device and result in injury
and / or damage to property.
Ensure that any spacers supplied and
required for the use of certain abrasive
consumables and tools are installed.
Do not use separate reducing bushes
or adapters in order to make grinding
discs with a larger bore fit.
When using abrasive consumables
and tools with a threaded insert make
sure that the tread is long enough for
the spindle length. Otherwise the grinding
General safety advice for electrical power tools
13 GB/IE/CY
discs could become detached from the device
and result in injury and / or damage to property.
Do not allow the end of the spindle
to contact the base of the hole in the
abrasive consumable.
Do not work in areas where there may
be concealed electricity cables or gas
or water pipes. Use a suitable detector
or ask your local utility service pro-
viders. Contact with electricity cables can
lead to fire or electric shock. Damaging a gas
pipe can lead to an explosion. Penetration of a
water pipe can lead to property damage or to
electric shock.
NOXIOUS FUMES!
Working with harmful / noxious dusts represents
a risk to the health of the person operating the
device and to anyone near the work area.
For longer periods of cutting or grind-
ing metal or stone materials which
give rise to dusts that are hazardous
to health, the device must be connected
to a suitable external dust extraction
device.
Ensure that there is adequate ventila-
tion when working on plastic, paint,
varnish etc.
Do not soak the materials or the sur-
face you are about to work on with
liquids containing solvents.
DANGER OF INJURY! Wear close-fitting
clothing and keep long hair inside a
hairnet or suitable headwear.
For safety reasons this device must
always be used with the auxiliary
handle
4
in place.
The adjustable disc guard cover
5
must
always be in place when working with
roughing, grinding or cutting discs.
Otherwise there could be danger of injury.
Use the vacuum dust extraction facility
if your work generates high amounts
of dust. Use suction devices particular-
ly approved for the purpose.
Use permitted consumables and tools
only. Check that the speed given on the
discs is greater or equal to the rated
speed of the device.
Take note of the direction of rotation
and always hold the device in such a
way that the sparks and grinding de-
bris are thrown away from your body.
Otherwise there could be danger of injury.
Make sure that the dimensions of the
disc are suitable for the device and
that the disc is of a type that fits prop-
erly on to the mounting flange
8
.
Advice on use
Note! Discs must be used only for their recom-
mended purposes, otherwise they could disintegrate,
become damaged or cause accidents.
Roughing (see Fig. G):
Never use cutting discs for
roughing or grinding!
Move the angle grinder using even
pressure to and fro over the workpiece.
Hold the roughing or grinding disc at
a flat angle to the workpiece when
working on a soft material. Use a
slightly steeper angle for harder ma-
terials.
Disc-cutting (see Figs. E, F):
Never use roughing or
grinding discs for cutting!
Only use certified fibre-reinforced cut-
ting or grinding discs approved for use at
circumferential speeds of not less than 80 m / s.
CAUTION! The disc continues to rotate after
the device has been switched off. Do not at-
tempt to slow it down by pressing on the side
of the disc.
Securely support the workpiece. Use
clamps or a vice to grip the workpiece firmly.
This is much safer than holding it in your hand.
Switch the device off and allow it to
come to a complete standstill before
you put it down.
Unlock the ON / OFF switch immedi-
ately if a power failure occurs or the
General safety advice for electrical power tools
14 GB/IE/CY
plug is pulled out of the mains socket.
Place the switch in the OFF position.
This prevents the device from being inadvertent-
ly started up again.
Use the device for dry cutting or dry
grinding only.
The auxiliary handle
4
must be in
place
whenever the device is being used.
Do not work on materials containing
asbestos. Asbestos is a known carcinogen.
A tip! Using the device safely.
DANGER! Always guide
the device through the
workpiece against the di-
rection of rotation of the
disc. If you work in the other direction there is
the risk of kickback. The device may be forced
out of the cut.
Always switch on the device before
placing it against the workpiece. After
cutting or grinding, always lift the device from
the workpiece before switching it off.
When working always hold the device
securely with both hands (see Fig. G).
Always keep proper footing and balance.
For the best grinding performance move the
device evenly to and fro over the workpiece
maintaining an angle of 15° to 30° (between
grinding disc and workpiece).
When working on inclined surfaces do
not press the device hard down on to
the workpiece. If the speed slows greatly,
use less pressure. This will allow you to work
more effectively and safely. If the device sudden-
ly stops due to it becoming retarded or trapped,
pull the mains plug from the socket immediately.
Cutting: Advance the device at an
appropriate rate. Do not incline the
cutting disc.
Roughing, grinding and cutting discs
get hot during use – allow them to
cool fully before touching them.
Never use the device for a purpose
for which it was not intended.
Before you insert the mains plug into
the socket, always check that the de-
vice is switched off.
If a dangerous situation arises, pull
the mains plug immediately out of the
mains socket. Ensure that the device and
the mains plug are easily accessible and can
be reached quickly in an emergency.
When taking a break from your
work, before carrying out any tasks
on the device itself and when you are
not using the device, always pull the
mains plug out of the mains socket.
Always keep the device clean, dry and free of
oil or grease.
Remain alert at all times! Always watch
what you are doing and proceed with
caution. Do not use the device if you cannot
concentrate or you are feeling unwell.
Use
Switching on and off
Check the attached consumable or tool before use.
It must be attached properly, not damaged, damp
or cracked and must rotate freely. Test the operation
of the device for 30 seconds. If a disc is not round
or vibrates, do not use it. Look out for unusual noises
or generation of sparks. Check that all the fastenings
are correctly attached.
Switching on:
Press the safety lock-out
1
.
Press the ON / OFF switch
2
.
Switching off:
Release the ON / OFF switch
2
again.
Setting the speed
Select the desired speed before use to suit your
purpose. Turn the speed preselector wheel
10
to the desired setting. The required rotational
speed depends on the material being worked
General safety advice for electrical power tools / Use
15 GB/IE/CY
and the working conditions and can be deter-
mined by means of a practical test.
The table below shows some recommended
settings (for guidance only and given without
liability) for a number of common applications.
The accessories mentioned may not all be sup-
plied as standard with the product. Sawing stone
is only permitted with the use of a cutting guide
(accessory).
Preselected rotation speed:
Material
Application
Tool Setting
Plastic,
varnish
Polishing Lambswool
bonnet
1
Fine finish
Felt polishing
disc
1
Metal Fine finish Buffing disc 1
Paint
removal
Sanding sheet 2–3
Wood,
metal
Brushing,
derusting
Cup brush,
sanding sheet
3
Metal,
stone
Grinding /
abrading
Grinding disc 4–6
Metal Roughing /
grinding
Roughing /
grinding disk
6
Stone Cutting Cutting disc
and cutting
guide
6
Changing a disc
Always wear protective gloves
when changing cutting or roughing /
grinding discs.
Press the spindle lock button
9
only after the
mounting spindle
7
has reached a standstill,
Fig. A.
Press the spindle lock button
9
to block the
drive.
Release the clamping nut
6
using the spanner
11
, Fig. B.
Place the roughing, grinding or cutting disc on
to the mounting flange
8
with its labelled side
facing towards the device.
Then replace the clamping nut
6
, with its
raised side facing upwards, on to the mounting
spindle
7
.
Press the spindle lock button
9
to block the
drive.
Tighten the clamping nut
6
again with the
spanner
11
.
Note: Replace a new disc immediately if it runs
unevenly or vibrates after being exchanged.
After replacing a disc let the device run under
no load for 30 seconds as a safety check.
Look out for unusual noises or generation of
sparks.
Check that all the fastenings are correctly
attached.
Pay attention to see that the arrow showing the
direction of rotation on the cutting or roughing /
grinding discs (including diamond cutting discs)
corresponds with the direction of rotation of the
device (see arrow on the head of the device).
Use of accessories
Cutting / roughing discs
You can use the following cutting or roughing/
grinding discs with this device:
Dimensions: ø 125 x 22,2 mm
to max. 6 mm thick
(depressed centre)
Speed: min. 12000 rpm
Circumferential speed: 80 m / sec
ø 125 x 22.2 mm
to max. 6 mm thick
(depressed centre)
12000 rpm
80 m / sec
Flap discs for metal
Dimensions: ø 125 mm
Speed: min. 12000 rpm
Use / Use of accessories
16 GB/IE/CY
Other accessories
You can also use abrasive consumables and tools
complying with the following technical specification:
Spindle thread: M14
Speed: min. 12000 rpm
Backing plate for grinding discs
Dimensions: ø 115 mm / 125 mm
Grinding discs for wood / masonry attached
with hook and eye fixings
Dimensions: ø 115 mm / 125 mm
Note! These may only be used in combination
with a backing plate!
Cup brush, crimped wire
Dimensions: ø 75–100 mm
Speed: min. 12000 rpm
Cup brush, twisted wire
Dimensions: ø 75 mm
Speed: min. 12000 rpm
Cup brush, knotted wire
Dimensions: ø 115 mm
Speed: min. 12000 rpm
Adjusting the disc guard cover
DANGER OF INJURY!
Pull the mains plug out of the mains socket
before you carry out any task on the device.
DANGER OF INJURY! Always use the an-
gle grinder with the disc guard cover
5
in
place. The disc guard cover must be securely
attached to the angle grinder. To ensure the
highest level of safety while using the device,
ensure that the smallest possible area of the
grinding or cutting tool is exposed to the oper-
ator at all times (see Fig. B, C). The disc guard
cover
5
is there to protect the operator from
pieces breaking off and accidental contact
with the grinding or cutting tool. The disc guard
cover has 5 set positions.
Turn the disc guard cover
5
into the desired
position (working position).
The closed side of the disc guard cover
5
must
always be facing the operator.
Use of accessories
17 GB/IE/CY
Using the auxiliary handle
CAUTION! For safety reasons this device must
always be used with the auxiliary handle
4
in
place.
The auxiliary handle
4
can be screwed on to the
left, right or on the top of the head of the device.
Maintenance and cleaning
DANGER OF INJURY!
Pull the mains plug out of the mains socket
before you carry out any task on the device.
Do not use sharp objects for cleaning
the device. Do not allow any liquids
to enter the device. Otherwise the tool may
be damaged.
Have the carbon brushes replaced only at the
service centre or an accredited electrical
equipment repair centre. The device requires
no other maintenance.
Clean the device frequently; for best results do
this immediately after you have finished using it.
Use a dry cloth to clean the housing – under
no circumstances use petrol, solvents or clean-
ing agents that attack plastic.
A vacuum cleaner is required to thoroughly
clean
the device.
Ventilation openings must always be kept free.
Remove any adhering dust with a narrow paint
brush.
Service
Have your device repaire
d
at the service centre or by qualified
specialist personnel using original
manufacturer parts only. This will ensure
that your device remains safe to use.
If the plug or lead needs
to be replaced, always have the re-
placement carried out by the manu-
facturer or its service centre. This will
ensure that your device remains safe to use.
Warranty
The warranty for this appliance is for 3 year
s
from the date of purchase. The appliance
has been manufactured with care and me-
ticulously examined before delivery. Please
retain your receipt as proof of purchase. In
the event of a warranty claim, please make
contact by telephone with our Service
Department. Only in this way can a post-
free despatch for your goods be assured.
The warranty covers only claims for material and
maufacturing defects, but not for transport damage,
for wearing parts or for damage to fragile components,
e.g. buttons or batteries. This product is for private use
only and is not intended for commercial use.
The warranty is void in the case of abusive and
improper handling, use of force and internal tam-
pering not carried out by our authorized service
branch. Your statutory rights are not restricted in
any way by this warranty.
The warranty period will not be extended by repairs
made unter warranty. This applies also to replaced
and repaired parts. Any damage and defects extant
on purchase must be reported immediately after
unpacking the appliance, at the latest, two days after
the purchase date. Repairs made after the expiration
of the warranty period are subject to payment.
GB
Service Great Britain
Tel.: 0871 5000 720
(0,10 GBP/Min.)
e-mail: k[email protected]
IAN 68725
IE
Service Ireland
Tel: 1890 930 034
(0,08 EUR/Min. (peak)
0,06 EUR/Min. (off peak))
e-mail: k[email protected]
IAN 68725
Use of accessories / Maintenance and cleaning / Service / Warranty
18 GB/IE/CY
CY
Service Cyprus
Tel.: 8009 4409
e-mail: k[email protected]
IAN 68725
Disposal
The packaging is wholly composed of
environmentally-friendly materials that can
be disposed of at a local recycling centre.
Do not dispose of electric tools
in the household waste!
In accordance with European Directive 2002 / 96 / EC
(covering waste electrical and electronic equipment)
and its transposition into national legislation, worn out
electrical power tools must be collected separately
and taken for environmentally compatible recycling.
Contact your local refuse disposal authority for more
details of how to dispose of your worn out electrical
devices.
Declaration of Conformity /
Manufacturer
We, Kompernaß GmbH, the person responsible for
documents: Mr Semi Uguzlu, Burgstr. 21, D-44867
Bochum, Germany, hereby declare that this product
complies with the following standards, normative
documents and EU directives:
Machinery Directive
(2006 / 42 / EC)
EU Low Voltage Directive
(2006 / 95 / EC)
Electromagnetic Compatibility
(2004 / 108 / EC)
Applicable harmonized standards
EN 60745-1:2009
EN 60745-2-3/A11:2009
EN 55014-1/A1:2009
EN 55014-2/A2:2008
EN 61000-3-2/A2:2009
EN 61000-3-3:2008
Type / Device description:
Angle grinder PWS 125 A1
Date of manufacture (DOM): 10–2011
Serial number: IAN 68725
Bochum, 31.10.2011
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical modifications
in the course of further development.
Warranty / Disposal / Declaration of Conformity / Manufacturer
19 GR/CY
Εισαγωγή
Χρήση σύμφωνα με τους κανονισμούς ......................................................................Σελίδα 20
Εξοπλισμός ..................................................................................................................Σελίδα 20
Περιεχόμενα παράδοσης ............................................................................................Σελίδα 21
Τεχνικά δεδομένα .........................................................................................................Σελίδα 21
Γενικές υποδείξεις ασφάλειας για ηλεκτρικά εργαλεία
1. Θέση εργασίας-ασφάλεια .......................................................................................Σελίδα 21
2.
Ηλεκτρική ασφάλεια ................................................................................................Σελίδα 22
3. Ασφάλεια ατόμων ....................................................................................................Σελίδα 22
4.
Ασφαλής λειτουργία και χρήση ηλεκτρονικών συσκευών .....................................Σελίδα 23
Υποδείξεις ασφάλειας για όλες τις εφαρμογές .........................................................Σελίδα 23
Ανάκρουση και αντίστοιχες υποδείξεις ασφάλειας ..................................................Σελίδα 25
Ειδικές υποδείξεις ασφάλειας για λείανση και διαχωρισμό .....................................Σελίδα 26
Περαιτέρω ειδικές υποδείξεις ασφάλειας για δίσκους διαχωρισμού.......................Σελίδα 26
Ειδικές υποδείξεις ασφάλειας για λείανση με γυαλόχαρτο ......................................Σελίδα 27
Ειδικές υποδείξεις ασφάλειας για γυάλισμα .............................................................Σελίδα 27
Ειδικές υποδείξεις ασφάλειας για εργασία με ψήκτρες ............................................Σελίδα 27
Υποδείξεις ασφάλειας για γωνιακό λειαντήρα ..........................................................Σελίδα 27
Υποδείξεις εργασίας ...................................................................................................Σελίδα 28
Χειρισμός
Ενεργοποίηση και απενεργοποίηση ...........................................................................Σελίδα 30
Ρύθμιση αριθμού στροφών .........................................................................................Σελίδα 30
Αντικατάσταση εργαλείων λείανσης ............................................................................Σελίδα 30
Χρήση εξαρτημάτων
Δίσκοι διαχωρισμού / τορναρίσματος ....................................................................... Σελίδα 31
Επίπεδοι δίσκοι λείανσης για μέταλλο .......................................................................Σελίδα 31
Περαιτέρω εξαρτήματα ................................................................................................Σελίδα 31
Ρύθμιση προστατευτικό κάλυμμα ................................................................................Σελίδα 32
Χρήση πρόσθετης χειρολαβής ...................................................................................Σελίδα 32
Συντήρηση και καθαρισμός .....................................................................Σελίδα 32
Σέρβις ..........................................................................................................................Σελίδα 32
Εγγύηση ....................................................................................................................Σελίδα 33
Απόσυρση ...............................................................................................................Σελίδα 33
Δήλωση συμμόρφωσης / Κατασκευαστής .....................................Σελίδα 34
Πίνακας περιεχομένων
20 GR/CY
Eισαγωγή
Γωνιακος τροχος PWS 125 A1
Λείανση, τορνάρισμα, διαχωρισμός
Εισαγωγή
Εξοικειωθείτε με τις λειτουργίες της συ-
σκευής πριν από την πρώτη θέση σε λει-
τουργία και πληροφορηθείτε σχετικά με
την ορθή συναναστροφή με ηλεκτρονικές συσκευές.
Για το λόγο αυτό διαβάστε τις παρακάτω οδηγίες
λειτουργίας.Φυλάξτε τις οδηγίες αυτές. Παραδώστε
όλα τα έγγραφα κατά τη μεταβίβαση της συσκευής
σε τρίτο.
Χρήση σύμφωνα με τους
κανονισμούς
Η συσκευή είναι κατάλληλη για το διαχωρισμό, το
τορνάρισμα και το βούρτσισμα μετάλλων και πετρών
χωρίς τη χρήση νερού. Οποιαδήποτε άλλη χρήση
ή τροποποίηση της συσκευής θεωρείται ως αντικα-
νονική και εγκυμονεί σοβαρούς κινδύνους ατυχη-
μάτων.Ο κατασκευαστής δεν αναλαμβάνει καμία
ευθύνη για φθορές που οφείλονται σε μη ορθή
χρήση.Η συσκευή δεν προορίζεται για βιομηχανική
εφαρμογή.
Υπόδειξη: Οι χαραμάδες σε φέροντες τοίχους
πρέπει να ανταποκρίνονται στο πρότυπο DIN 1053
μέρος 1 ή στους κατά τόπους κανονισμούς.
Οι εν λόγω διατάξεις πρέπει να τηρούνται οπωσδήποτε
.
Καλέστε για να ενημερωθείτε σχετικά τον υπεύθυνο
στατικό επιστήμονα, αρχιτέκτονα ή την αρμόδια κα-
τασκευαστική διεύθυνση.
Εξοπλισμός
1
Φραγή ενεργοποίησης
2
Διακόπτης ΕΝΤΟΣ / ΕΚΤΟΣ
3
Κάλυμμα ψηκτρών
4
Πρόσθετη χειρολαβή
5
Ρυθμιζόμενο προστατευτικό κάλυμμα
6
Παξιμάδι συγκράτησης
Σε αυτές τις οδηγίες χρήσης / συσκευής μπορούν να χρησιμοποιηθούν τα
παρακάτω εικονογράμματα:
Διαβάστε τις οδηγίες χρήσης!
n
0
Ονομαστικές στροφές κατά τη
λειτουργία εν κενώ
Προσέχετε τις προειδοποιητικές υπο-
δείξεις και τις υποδείξεις ασφαλείας!
Κατηγορία προστασίας II
Προσοχή για ηλεκτροπληξία!
Κίνδυνος ζωής!
Ετσι συμπεριφέρεστε σωστά.
Κίνδυνος έκρηξης!
Φοράτε προστατευτικά γυαλιά, ωτοα-
σπίδες, μάσκα στόματος που προ-
στατεύει από τη σκόνη και προστατευ-
τικά γάντια.
Κίνδυνος πυρκαγιάς!
Κρατήστε τα παιδιά μακριά από
ηλεκτρικά εργαλεία!
V
~
Volt (Εναλλασσόμενη τάση)
Κίνδυνος θάνατος από ηλεκτροπληξία
όταν είναι ελαττωματικό το καλώδιο ή
το βύσμα δικτύου!
W
Watt (Αποτελεσματική ισχύς)
Απομακρύνετε τη συσκευασία και τη
συσκευή φιλικά προς το περιβάλλον!
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
Parkside PWS 125 A1 ANGLE GRINDER Operation and Safety Notes
- Typ
- Operation and Safety Notes
- Dieses Handbuch ist auch geeignet für
in anderen Sprachen
- English: Parkside PWS 125 A1 ANGLE GRINDER
Verwandte Papiere
-
Parkside PWS 230 A1 ANGLE GRINDER Operation and Safety Notes
-
Parkside PWS 230 C3 Translation Of The Original Instructions
-
Parkside KH 3177 ANGLE GRINDER Operation and Safety Notes
-
Kompernass PWS 230 Bedienungsanleitung
-
Parkside PWS 230 SE - MANUEL 2 Operation and Safety Notes
-
-
-
Parkside PWS 1010 Operation and Safety Notes
-
-
