Philips FR 740 & FR740 Bedienungsanleitung

Surround sound receiver

FR740

FR760

MX740

Important notes for users in the U.K.

Mains plug

This apparatus is fitted with an approved 13 Amp plug.

To change a fuse in this type of plug proceed as follows:

1 Remove fuse cover and fuse.

2

Fix new fuse which should be a

BS1362

5 Amp, A.S.T.A. or BSI approved type.

3 Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it

should be cut off and an appropriate plug fitted in its place.

If the mains plug contains a fuse, this should have a value

of 5 Amp. If a plug without a fuse is used, the fuse at the

distribution board should not be greater than 5 Amp.

Note: The severed plug must be disposed of to avoid a

possible shock hazard should it be inserted into a 13 Amp

socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the following

code: blue = neutral (N), brown = live (L).

As these colours may not correspond with the colour

mark

ings identifying the terminals in your plug, proceed as

follows:

• Connect the blue wire to the terminal marked N or

coloured black.

• Connect the brown wire to the terminal marked L or

coloured red.

•

Do not connect either wire to the earth terminal in the

plug,

marked E (or e) or coloured green (or green and

yellow).

Before replacing the plug cover, make certain that the cord

grip is clamped over the sheath of the lead - not simply over

the two wires.

Copyright in the U.K.

Recording and playback of material may require consent.

See

Copyright Act 1956 and The Performer’s Protection Acts

1958 to 1972.

Typeskilt finnes på apparatens bakside.

Observer: Nettbryteren er sekundert innkoplet. Den

innebygde netdelen er derfor ikke frakoplet nettet så lenge

apparatet er tilsluttet nettkontakten.

For å redusere faren for brann eller elektrisk støt, skal

apparatet ikke utsettes for regn eller fuktighet.

Norge

DICHIARAZIONE DI CONFORMITA’

Si dichiara che gli apparecchi FR 740, FR 760 e MX 740

Philips rispondono alle prescrizioni dell’art. 2 comma 1 del

D. M. 28 Agosto 1995 n. 548.

Fatto a Eindhoven, il 01/02/2000 (FR 740, MX 740)

Fatto a Eindhoven, il 01/03/2000 (FR 760)

Philips Consumer Electronics

Philips, Glaslaan 2

5616 JB Eindhoven, The Netherlands

Italia

2

3

English ....................................................4

Français.................................................24

Español .................................................44

Deutsch.................................................64

Nederlands ...........................................84

EnglishFrançaisEspañolDeutschNederlands

Italiano

Italiano................................................104

GENERAL INFORMATION

4

This receiver is supplied including:

– a remote control

– 2 batteries for the remote control, size AA

– a system bus cable for the CINEMA LINK connection

– a loop antenna

– a wire antenna

– 5 loudspeakers including 5 speaker cables (MX 740 only)

– a quick installation card (MX 740 only)

– this instruction booklet

Clean the receiver with a soft,

slightly dampened, lint-free cloth.

Do not use any cleaning agents as

they may have a corrosive effect.

Do not expose the receiver to

humidity, rain, sand or excessive heat

(caused by heating equipment or

direct sunlight).

If you have stacked the components of your system, the

receiver must be on top. Place the receiver on a flat,

hard, stabile surface. Do not cover any vents and leave

50 cm above and 10 cm left and right of the receiver

free for ventilation.

For good reception the loop antenna should not be placed on

top of, or beneath VCRs, CD recorders, DVD players, TVs and

other radiation sources.

All redundant packing material has been omitted. We have

done our utmost to make the packaging easily separable into

three mono materials: cardboard (box), polystyrene foam

(buffer) and polyethylene (bags, protective foam sheet).

Your set consists of materials which can be recycled if

disassembled by a specialized company. Please observe the

local regulations regarding the disposal of packing materials,

exhausted batteries and old equipment.

“DOLBY”, “DOLBY DIGITAL”, “PRO LOGIC” and the

double-D symbol 2 are trademarks of Dolby Laboratories.

Trademark acknowledgment

Environmental information

Setup

Maintenance

Scope of supply

English

General information

Scope of supply..................................................................................4

Maintenance......................................................................................4

Setup ..................................................................................................4

Environmental information.................................................................4

Trademark acknowledgment..............................................................4

Controls .................................................................................................5

Remote control

Remote control usage........................................................................6

Remote control buttons .....................................................................7

Connectors............................................................................................8

Connections

Audio connections..............................................................................9

System control bus, CINEMA LINK .................................................10

Video connections (FR 760 only)......................................................10

Mains ...............................................................................................11

Speaker connections........................................................................11

TV as the center speaker.................................................................11

Antenna connections .......................................................................11

FRONT AV / GAME cap (FR 760 only)..............................................11

System setup

Positioning of the speakers .............................................................12

Speaker setup and testing...............................................................12

Power handling ................................................................................12

Headphones .....................................................................................12

Display.................................................................................................13

Menus

Receiver menu..................................................................................14

TV menu ...........................................................................................15

Source selection

SOURCE SELECTOR..........................................................................16

About 6 CHANNEL / DVD INPUT.....................................................16

Playback, recording

Playing a source...............................................................................17

Adjusting the sound.........................................................................17

Recording from a source..................................................................17

Surround sound

About surround sound......................................................................18

Switching surround sound ...............................................................18

Surround sound settings..................................................................18

Tuner

Tuning to radio stations ...................................................................19

Switching FM sensitivity .................................................................19

Storing radio stations ......................................................................19

Tuning to stored radio stations........................................................20

Resorting stored radio station.........................................................20

Naming radio stations .....................................................................20

Clearing station names....................................................................20

RDS R..............................................................................................21

RDS News and Traffic Announcement............................................21

Technical data

Receiver............................................................................................22

Speakers (supplied with MX 740 only)............................................22

Troubleshooting

Warning............................................................................................23

Troubleshooting................................................................................23

This product complies with the radio interference

requirements of the European Community.

As an ENERGY STAR

®

partner, Philips has determined that

this product meets the ENERGY STAR

®

guidelines for energy efficiency.

CONTROLS

5

1 POWER / STANDBY.......Switches the receiver on and off.

2 CINEMA LINK ................Switches the system control bus

between the receiver and the TV

on and off.

3 ..........................................Sensor for the infrared remote

control.

4 ..........................................Display

5 SOURCE SELECTOR ......Selects the different audio and

video connectors.

6 VOLUME..........................Increases and decreases the

volume level.

7 FRONT AV.......................Selects the FRONT AV / GAME

input (FR 760 only).

8 TREBLE............................Adjusts the treble when used in

combination with VOLUME.

9 BASS...............................Adjusts the bass when used in

combination with VOLUME.

0 LOUDNESS.....................Switches LOUDNESS on and off.

! NEXT 2 ...........................TUNER: searches radio stations.

MENU: switches to the next

menu level.

@ ENTER / OK.....................Confirms selected menu values.

# TUNER PRESET X MENU NAVIGATOR

TUNER: switches to the next and

previous stored radio station.

MENU: moves upwards and

downwards.

$ 1 PREV. / EXIT ...............TUNER: searches radio stations.

MENU: switches to the previous

menu level.

% SETUP MENU ................Switches the menu on and off.

^ SENS. ..............................Switches between low and high

tuner sensitivity.

& NEWS/TA........................Switches the RDS news and

RDS traffic announcement on

and off.

* TUNER AM/FM ..............Switches the wavebands of the

tuner.

( RADIO TEXT ...................Scrolls through the different RDS

information.

) SURR. MODE..................Switches through the different

speaker configurations.

¡ HALL................................Switches HALL on and off.

™ SURROUND ON/OFF .....Switches between the last

selected surround mode and

stereo.

English

POWER / STANDBY

CINEMA LINK

PHONES

CINEMA SOUND CENTER

LOUDNESS

BASS

TREBLE

AV

SOURCE SELECTOR

VOLUME

SURROUND

SURR. MODE

HALL

TUNER AM/FM

RADIO TEXT

SENS.

NEWS/TA

PREV. / EXIT

SETUP MENU

ON/OFF

MENU

NAVIGATOR

TUNER

PRESET

FRONT AV / GAME

6CH/DVD

1 23 4 5

6

7

8

9

0!@#$%^&*()¡™

REMOTE CONTROL

6

Open the battery compartment

of the remote control and insert

2 alkaline batteries, type AA

(R06, UM-3).

Remove batteries if they are flat

or if the remote control is not

going to be used for a long time.

Batteries contain chemical substances, so they should

be disposed of properly.

The buttons on the remote control work the same way as the

corresponding ones on the receiver.

Additional appliances can only be controlled if they are

working with the RC-5 and the RC-6 code system.

Important!

You have to press a source button for longer than 1 second to

switch the sound source on the receiver. Pressing a source

button for less than 1 second will only switch the remote

control to use the commands for the selected product.

The remote control remains tuned to the selected source until

another source button on the remote control is pressed.

This enables you to operate additional sources (i. e. winding

a tape) without changing the source on the receiver.

Remote control usage

English

2

AA

TV

MENU

H

1

3

2

4

6

5

7

9

8

0

+

b

-

íëÅ

Ç

É

±

DVD/6CH

OK

CINEMA LINK

GUIDE

DISC

FR.D/INDEXPAUSE

SURR. ON/OFFDISPLAY/T-C NEWS/TA

SURR. MODESMART SOUND

REAR

CHANNEL

TEST TONELOUDNESS

CHANNEL/TRACK

TUNER

CD CDR/TAPE VCR TV

REMOTE CONTROL

7

English

2 ................................Switches the receiver to standby.

TUNER, CD, CDR/TAPE,

TV, VCR, DVD/6CH........Switches the remote control to the

commands of the different products.

Selects the sources if pressed longer

than 1 second.

1–0................................Keys in numbers for tracks, stations or

frequencies. Numbers consisting of

two figures must be keyed in within

2 seconds.

CINEMA LINK...............Switches the connection between the

receiver and the TV on and off.

MENU GUIDE ..............TUNER: Switches the receiver menu

on and off.

DVD, TV: Switches the DVD/TV menu

on and off.

OK.................................Confirms menu options.

Arrow buttons ..............TUNER: Moves in the menus.

Right/left arrows are tuning up/down.

CD, CDR: Left/right arrows are

searching backwards/forwards,

up/down arrows are selecting the

next/previous track.

+A...........................Increases the receiver volume.

-A...........................Decreases the receiver volume.

H ................................Mutes the sound of the receiver.

ÉATV ......................Increases the TV volume.

CD, CDR, VCR, DVD: Starts playback.

ÇATV ......................Decreases the TV volume.

CD, CDR, VCR, DVD: Stops playback.

í

CHANNEL/TRACK

...Selects the previous preset tuner

station.

VCR: Rewinds the tape.

CD, CDR, DVD: Selects the previous

track.

TV: Selects the previous channel.

ë

CHANNEL/TRACK

...Selects the next preset tuner station.

VCR: Fast forwards the tape.

CD, CDR, DVD: Selects the next

track.

TV: Selects the next channel.

Å PAUSE...................CD, CDR, VCR, DVD: Pauses

playback.

DISC FR.D./INDEX ........CD-, CDR-, DVD-Changers:

Switches to the next disc.

TUNER: Switches to FREQUENCY

DIRECT.

VCR: Switches the index search on

and off.

b DISPLAY/T-C...........TUNER: Switches between station

name, frequency and radio text.

CD, CDR: Switches between the

different time displays.

TV: Switches teletext on and off.

DVD: Switches between title and

chapter.

NEWS/TA .....................Switches the functions NEWS and

TRAFFIC ANNOUNCEMENT on and off.

SURR. ON/OFF..............Switches SURROUND SOUND on and

off.

±SMART SOUND ......Scrolls through the different smart

sounds.

+/- REAR ...............Increases/decreases the volume of the

rear speakers. While test tone is on,

the volume of the speakers you are

hearing can be increased/decreased

with these buttons.

SURR. MODE................Scrolls through the different surround

modes.

LOUDNESS ...................Switches LOUDNESS on and off.

TEST TONE ...................Switches the test tone on and off.

While test tone is on, the volume of

the speakers you are hearing can be

increased/decreased with

+/- REAR.

Remote control buttons

8

English

CONNECTORS

Connectors Connectors name Connect to:

6.3 mm headphone socket 1 PHONES A headphone with a 6.3 mm plug.

at the front

Audio and video inputs 2 FRONT AV / GAME Left and right audio out sockets of appliances such as video cameras

at the front (FR 760 only) and game consoles.

3 FRONT AV / GAME Video out sockets of appliances such as video cameras and game

consoles.

FRONT SPEAKERS 4 R, L Right and left front speaker.

5 CENTER Center speaker.

SURROUND SPEAKERS 6 R, L Right and left surround speaker.

AUDIO IN/OUT 8 CDR/TAPE OUT Input of a CD recorder or a tape deck.

9 CDR/TAPE IN Output of a CD recorder or a tape deck.

0 CD IN Output of a CD player.

! TV IN Output of a TV.

@ VCR OUT Input of a video recorder.

# VCR IN Output of a video recorder.

6-channel input $

6 CHANNEL /DVD INPUT

6-channel output of appliances such as DVD or Laserdisc players.

VIDEO IN/OUT (FR 760 only) % DVD IN Output of a DVD player.

^ MON OUT Input of a monitor (e. g. the TV).

* VCR IN Output of a video recorder.

( VCR OUT Input of a video recorder (for recording).

¡ TV IN Output of a TV.

Antenna connectors &

AM LOOP

Frame antenna supplied.

) FM 75 Ω Wire antenna supplied or exterior antenna.

Preamplified outputs 7 CENTER PRE-OUT Input of a TV when it is used as the center speaker (only possible

when the CINEMA LINK system bus is connected).

™

SUBWOOFER PRE-OUT

Input of a powered subwoofer.

System control bus £ CINEMA LINK System control bus sockets of a Philips TV with CINEMA LINK.

Mains outlet ≤ AC OUTLET Supplies same voltage as mains. Up to 100 W total permitted load.

Mains lead ∞ After all other connections have been made, connect the

mains lead to the wall socket.

POWER / STANDBY

CINEMA LINK

PHONES

SURROU

N

ON/O

F

TOTAL 100W MAX. SWITCHED

AC OUTLET

230V

~50 Hz

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

Designed

and

developed

by Philips

in the

European Community

IN

PLAY

OUT

REC

IN

PLAY

OUT

REC

IN

OUT

REC

IN

PLAY

ANTENNA

FM

75

Ω

VIDEO IN/OUT

AM LOOP

DVD

MON

VCR

TV

SUBWOOFER

PRE-OUT

VCR

TV

CD

CDR/T

APE

AUDIO IN/OUT

IN

PRE-OUT

CENTER

Manufactured

under

licence

from

Dolby

Laboratories

Licencing

Corporation.

"DOLBY",

"PRO-LOGIC"

and the Double-D

Symbol

are Trademarks

of Dolby

Laboratories

Licencing

Corporation.

FRONT SPEAKERS

L

R

EACH SPEAKER

≥ 6 Ω

CENTER

SURROUND SPEAKERS

R

L

EACH SPEAKER ≥ 3 Ω

L

R

L

R

FRONT

SURR.

CENTER

SUB-

WOOFER

6 CHANNEL / DVD INPUT

CINEMA

LINK

124567890!@#

$

%^&*() ¡™ ≤ ∞

£

3

9

English

CONNECTIONS

Audio connections

VIDEO IN/OUT

DVD MON TV/SAT

IN OUT

OUT

REC

IN

PLAY

TV CD CDR/TAPE

AUDIO IN/OUT

L

R

IN

PLAY

OUT

REC

IN IN

IN

PLAY

OUT

REC

PRE-OUT

CENTER

6 CHANNEL / DVD INPUT

FRONTSURR.

CENTER

SUB-

WOOFER

VCR

L

R

VCR

IN

CINEMA

LINK

SUBWOOFER

PRE-OUT

ANTENNA

AM LOOP

FRONT SPEAKERS

L

R

EACH SPEAKER ≥ 6 Ω

CENTER

Designed and developed by Philips in the

European Community

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC

ELECTRIQUE

Manufactured under licence from Dolby

Laboratories Licencing Corporation.

"DOLBY", "PRO-LOGIC" and the Double-D

Symbol are Trademarks of Dolby

Laboratories Licencing Corporation.

R

L

EACH SPEAKER ≥ 6 Ω

SURROUND SPEAKERS

AUDIO IN

AUDIO OUT

IN

OUT

VCR

SAT RECEIVER

CD RECORDER

CD PLAYER

DVD PLAYER

(6 Channel Output)

POWERED

SUBWOOFER

10

English

CONNECTIONS

System control bus, CINEMA LINK

Video connections (FR 760 only)

VIDEO IN/OUT

DVD MON TV/SAT

IN OUT

OUT

REC

IN

PLAY

TV CD CDR/TAPE

AUDIO IN/OUT

L

R

IN

PLAY

OUT

REC

IN IN

IN

PLAY

OUT

REC

PRE-OUT

CENTER

6 CHANNEL / DVD INPUT

FRONTSURR.

CENTER

SUB-

WOOFER

VCR

L

R

VCR

IN

CINEMA

LINK

SUBWOOFER

PRE-OUT

ANTENNA

AM LOOP

FRONT SPEAKERS

L

R

EACH SPEAKER ≥ 6 Ω

CENTER

Designed and developed by Philips in the

European Community

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC

ELECTRIQUE

Manufactured under licence from Dolby

Laboratories Licencing Corporation.

"DOLBY", "PRO-LOGIC" and the Double-D

Symbol are Trademarks of Dolby

Laboratories Licencing Corporation.

R

L

EACH SPEAKER ≥ 6 Ω

SURROUND SPEAKERS

DVD PLAYER

MONITOR / TV

VIDEO IN

VIDEO OUT

VCR

SAT RECEIVER

VIDEO IN/OUT

DVD MON TV/SAT

IN OUT

OUT

REC

IN

PLAY

TV CD CDR/TAPE

AUDIO IN/OUT

L

R

IN

PLAY

OUT

REC

IN IN

IN

PLAY

OUT

REC

PRE-OUT

CENTER

6 CHANNEL / DVD INPUT

FRONTSURR.

CENTER

SUB-

WOOFER

VCR

L

R

VCR

IN

CINEMA

LINK

SUBWOOFER

PRE-OUT

ANTENNA

AM LOOP

FRONT SPEAKERS

L

R

EACH SPEAKER ≥ 6 Ω

CENTER

Designed and developed by Philips in the

European Community

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC

ELECTRIQUE

Manufactured under licence from Dolby

Laboratories Licencing Corporation.

"DOLBY", "PRO-LOGIC" and the Double-D

Symbol are Trademarks of Dolby

Laboratories Licencing Corporation.

R

L

EACH SPEAKER ≥ 6 Ω

SURROUND SPEAKERS

TV to AMP

AUX to AMP

TV

AUX

EXT 1 EXT 2 EXT 3

DVD PLAYER

VCR

TV

optional

(TV = CENTER)

CINEMA LINK

A

If the receiver and your Philips TV (or even better in

addition a Philips VCR or DVD player) with Cinemalink are

connected with the CINEMA LINK system bus control, some

extra system benefits are offered:

– Upon starting a source, the system will automatically

switch to that input.

– You may control the system via the TV screen. Depending

on the language of the TV, this can be done in your

preferred language.

– The TV can function as the center speaker of your system,

making a separate center speaker unnecessary. (The cable

A has to be purchased separately.)

– By pressing the standby button on the remote control you

can switch the complete system to standby.

11

English

CONNECTIONS

The type plate is located on the rear of the receiver.

1 Check whether the mains voltage as shown on the type

plate corresponds to your local mains voltage. If it does not,

consult your dealer or service organization.

2 Connect the mains cable to the wall socket.

To disconnect the set from the mains completely, remove the

mains plug from the wall socket.

For users in the U. K.: please follow the instructions on

page 2.

The speaker connections on the receiver are click-fit

connectors. Use them as shown below.

1 Always connect the coloured (or marked) wire to the

coloured terminal and the black (or unmarked) wire to the

black terminal.

2 Connect:

– Left front speaker to L (red and black)

– Right front speaker to R (red and black)

– Center speaker to CENTER (blue and black)

– Left surround speaker to SURROUND L (grey and black)

– Right surround speaker to SURROUND R (grey and black)

You may use your Philips TV with CINEMA LINK as the center

speaker. For TVs with a scart connector an additional audio

cinch-to-scart cable is needed. For TV’s with cinch connectors

additional cinch cables are needed. Look into the instruction

manual of your TV on how to use it as the center speaker.

AM (MW) antenna

The loop antenna supplied is for indoor use only. Position the

antenna as far away as possible from the receiver, the TV, the

cables, a DVD player, a VCR and other radiation sources.

1 Fit the plug of the frame antenna to AM LOOP as shown

below.

2 Position the antenna as far away as possible from radiation

sources.

3 Turn the antenna for optimum reception.

FM antenna

The wire antenna supplied can only be used to receive nearby

stations. For better reception we recommend using a cable

antenna system or an outdoor antenna.

1 Fit the supplied wire antenna to FM 75 Ω as shown below.

2 Move the antenna in different positions for optimum

reception.

• If you are using a cable antenna system or an outdoor

antenna, fit the antenna plug to FM 75 Ω instead of the

wire antenna.

• To remove the FRONT AV / GAME cap, press on the right

side of the cap.

• Insert the cap from below to close the compartment.

PHONES

FRONT AV / GAME

PHONES

FRONT A

V / GAME

FRONT AV / GAME cap (FR 760 only)

FM 75 Ω

AM LOOP

ANTENNA

Antenna connections

TV as the center speaker

8 mm

1

2

3

Speaker connections

Mains

SYSTEM SETUP

12

General hints for positioning

Avoid positioning the speakers in a corner or on the floor as

this will boost the bass tones too much. Placing the speakers

behind curtains, furniture, etc. will reduce the treble response.

The listener should always be able to ”see” the speakers.

Each room has different acoustic characteristics and the

positioning possibilities are often limited. You can find the

best position for your speakers by referring to the picture

above.

As a minimum we recommend 5 speakers (2 front, a center,

2 surround) for good surround sound. It is possible to

reproduce some kind of surround sound with fewer speakers.

This is done by redirecting the signals which are foreseen for

the missing speakers to the existing ones. See “Menus” on

how to set up the receiver correctly for the number and size

of the speakers used.

Positioning the front speakers

The front speakers should be placed right and left in front of

the listening position like usual stereo speakers.

Positioning the center speaker

The center speaker should be placed in the center between

the two front speakers, e. g. underneath or on top of the TV.

The best height for the center speaker is the height of the

listener’s ears (while seated).

Positioning the surround speakers

The surround speakers should face each other and be in line

with, or slightly behind the listener.

Positioning the subwoofer

A subwoofer can be used to enhance the bass performance of

your system dramatically. The subwoofer can be positioned

anywhere in the room, because it is not possible to locate the

source of deep tones. Nevertheless, you should not place the

subwoofer in the middle of a room, since the bass could be

severely weakened. Do not place any object on the subwoofer.

The relative volume of the speakers must be adjusted for

optimal surround sound. You should be at your usual listening

position when adjusting the speaker volume. See “Receiver

menus” on how to set up the receiver for the used speakers.

Ideally, the volume in the listening position should be the

same from all speakers.

1 Press POWER / STANDBY to switch on the receiver.

2 Press TEST TONE on the remote control.

y A test tone coming from the different speakers is

heard.

3 Press +/- REAR on the remote control to

increase/decrease the volume of the actual speaker.

4 Press TEST TONE on the remote control.

y The test tone stops.

Note: If you are not completely satisfied with the volume

settings, we recommend making minor adjustments to

them during surround sound playback.

If the receiver is used at very high power, it can produce

distortions which may seriously damage your speakers.

If distortions occur, reduce the volume and the tone controls

to a level where the sound is acceptable again.

To avoid overheating of the set a safety circuit has

been built in. Therefore your set may disconnect under

extreme conditions. If this happens, switch the set off

and let it cool down before reusing it.

Connecting headphones to PHONES will switch off the

speakers. The receiver switches to STEREO and surround

sound will be reduced to a stereo signal which is reproducible

by standard headphones.

Disconnecting the headphones switches on the speakers

again. If you wish to enjoy surround sound again, switch the

receiver back to surround sound.

Headphones

Power handling

Speaker setup and testing

Positioning of the speakers

English

SUBWOOFER

SURROUND

(REAR)

LEFT

RIGHT

CENTER

FRONT

RIGHT

FRONT

SURROUND

(REAR)

13

English

DISPLAY

The display of the receiver is divided into 3 sections, which

are to be used for the following:

Menu indication

These signs show you if the menu is on or off and indicate in

which direction you may move.

MMEENNUU .......................Menu is on.

1..............................You may move backwards to the previous

menu topic using 1 PREV. / EXIT (“left”

key on the remote control).

3 .............................You may move up in an option list using

X MENU NAVIGATOR (“up” key on the

remote control).

4 .............................You may move down in an option list

using X MENU NAVIGATOR (“down” key

on the remote control).

2..............................You may move forward to the next menu

topic using NEXT 2 (“right” key on the

remote control).

OOKK.............................You may confirm the displayed value.

Status lights

Signs showing you various settings and information about the

status of the receiver.

PRESET ......................Tuner is tuned to a preset radio station.

SENS HI.....................Tuner is switched to high sensitivity.

SENS LO ..................Tuner is switched to low sensitivity.

CCIINNEEMMAA LLIINNKK OONN ......CINEMA LINK is active.

= ...........................An FM station is being received in stereo.

SMART SOUND...........One of the preset sound settings of the

receiver is being used.

R.............................An RDS station is being received.

EON...........................An RDS station with EON is being

received.

HALL..........................HALL effect is on.

TA .............................RDS traffic announcement is on.

NEWS........................RDS news announcement is on.

LOUDNESS .................LOUDNESS is switched on.

Information area

This area is used for feedback of the receiver, tuner

frequencies, menu options, values and scrolling text

messages.

AA

TV

MENU

H

0

Ç

É

OK

GUIDE

Display

14

English

MENUS

The receiver is equipped with a menu system. The menu is

used for the setup of the receiver. The different menu options

are related to each other in a logical way. Let’s assume you

have no center speaker connected, and therefore switched

CENTER LS to NO. If you try to use VOL CENTER, a

message will be scrolled that this is not possible (INSTALL

CENTER SPEAKER).

The menu always works the same way. Arrows in the display

show you the possible moving directions.

1 Press SETUP MENU.

yMENU, and * VOL BAL is displayed.

• You can exit the menu at any time by pressing

SETUP MENU.

2 Turn X MENU NAVIGATOR until the desired option (or a

value) is displayed.

3 Press NEXT 2 to choose the displayed option (or

ENTER / OK to confirm a value).

• You can leave any option (values remain unchanged) by

pressing 1 PREV. / EXIT.

Menu structure

* VOL BAL

Adjusts the relative volume balance between the

connected speakers.

TEST TONE

Test tone: on/off

VOL FR-L

Volume front left speaker: –50…+50

VOL FR-R

Volume front right speaker: –50…+50

VOL CENTER

Volume center speaker: –50…+50

VOL REAR-L

Volume rear left speaker: –50…+50

VOL REAR-R

Volume rear right speaker: –50…+50

VOL SUBW

Volume subwoofer: –50…+50

* LS SETUP

Selects the used speakers. Chooses the speaker sizes of

the used speakers, for optimal sound reproduction.

The distance between the usual listening position and the

speakers defines the delay time for the surround sound.

Note: When using the 6 CHANNEL / DVD IN input, these

values cannot be changed.

CENTER LS

Center speaker present: yes/no

REAR LS

Rear speakers present: yes/no

CENTR SIZE

Center speaker: small/large

DIST L/ R

Distance to front speakers: 1…10 m

DIST REAR

Distance to rear speakers: 1…10 m

* TUNER

Setup for preset radio stations (see “TUNER” for details).

AUTO INST

Stores radio stations automatically

MAN INST

Stores radio stations manually

GIVE NAME

Allows to assign names to stored radio stations

RESHUFFLE

Resorts stored radio stations

Receiver menu

15

English

MENUS

If the receiver is connected to a Philips CINEMA LINK TV

via the CINEMA LINK system control bus sockets

(see “CONNECTIONS”), you may use the TV to set up the

system. An option called RECEIVER will be added to the TV

menu.

If CINEMA LINK is on, adjustments on the receiver will be

shown on the TV screen for a few seconds. Consult the

instruction booklet of your TV on how to use the TV menu.

The options offered may vary by TV model.

Switching the connection

• Press CINEMA LINK to switch the connection between the

receiver and the TV either on or off.

yIf the connection is switched on, CINEMA LINK ON is

displayed.

Note: We recommend switching CINEMA LINK off during

recording. This avoids unwanted interruptions due to

switching TV functions.

If CINEMA LINK is switched on and the TV menu is active,

TV MENU is displayed and the menu and sound functions on

the receiver are locked.

TV menu

16

English

SOURCE SELECTION

When selecting a source by turning SOURCE SELECTOR,

the audio inputs – and video inputs (FR 760 only) – with the

corresponding name are activated. The incoming signal is

reproduced by all audio and – if the source includes a video

signal – video outputs of the receiver.

Source selected........Connectors used

6 CH / DVD...................6 CHANNEL / DVD INPUT audio input

and DVD IN video input (FR 760 only)

TUNER ..........................The tuner part of the receiver is used,

all inputs are switched off.

CD.................................CD IN audio input

CDR/TAPE.....................CDR/TAPE IN audio input

TV..................................TV IN audio input and

TV IN video input (FR 760 only)

VCR...............................VCR IN audio input and

VCR IN video input (FR 760 only)

The 6 CHANNEL / DVD INPUT can be used to connect a

device with a built-in multichannel decoder (e.g. Dolby Digital,

DTS, etc.) and 6-channel output connector, i. e. a high end

DVD player.

When using the 6 CHANNEL / DVD INPUT audio input, the

receiver works as a multichannel amplifier. The source

reproduces surround sound and sends it to the receiver

divided into the necessary channels. Therefore the

SURROUND ON/OFF, HALL and SURR. MODE button have no

effect since the provided signal is already multichannel.

From a source which is connected to the

6 CHANNEL / DVD INPUT audio input cannot be recorded.

About 6 CHANNEL / DVD INPUT

SOURCE SELECTOR

17

English

PLAYBACK, RECORDING

1 Press POWER / STANDBY to switch on the receiver.

2 Turn SOURCE SELECTOR to select a source.

yThe name of the source is displayed.

• You can select the FRONT AV/GAME input by pressing

FRONT AV (FR 760 only).

3 Start playback of the source as usual.

• Turn VOLUME to adjust the volume.

yVOLUME and the volume level between 0 and 50 is

displayed.

1 Press BASS or TREBLE.

yBASS or TREBLE and the actual value are displayed

briefly. Then TURN VOLUME KNOB TO CHANGE is

scrolled.

2 Turn VOLUME to adjust the bass or treble.

yBASS or TREBLE and the actual value are displayed.

Note : If VOLUME is not turned within 5 seconds or if any

other control is used, the bass or treble adjustment is

switched off.

• Press ±SMART SOUND on the remote control to scroll

through the built-in smart sounds: MOVIE, SPEECH,

MUSIC, MULTIMEDIA and PERSONAL.

(PERSONAL is the userdefined bass and treble setting.)

ySMART SOUND is displayed and the name of the chosen

sound profile is scrolled once if smart sound is on.

• Press LOUDNESS to switch loudness either on or off.

yLOUDNESS is displayed if loudness is on.

If you wish to record from a source you must select it with

SOURCE SELECTOR. The incoming signal is reproduced by all

audio and – if the source includes a video signal – video

outputs of the receiver. The sound settings do not affect the

recording.

1 Turn SOURCE SELECTOR (or press FRONT AV – FR 760 only)

to select the source you want to record from.

yThe name of the source is displayed.

2 Prepare the desired recording appliance. It must be

connected to one of the outputs of the receiver.

3 Start recording on the recording appliance.

4 Start the playback of the source as usual.

Notes: – The audio and video signal of VCR IN is not

reproduced by VCR OUT. The same applies to the

audio signal of CDR/TAPE IN to CDR/TAPE OUT.

– From a source which is connected to the

6 CHANNEL / DVD IN audio input cannot be

recorded.

Recording from a source

Adjusting the sound

Playing a source

18

English

SURROUND SOUND

Surround sound gives you a complete new listening sensation.

You will have the feeling of being in the middle of the action,

because sound is coming from everywhere around you. Look

out for TV broadcasts, audio and video tapes and discs with

the 3 or 1 marks which are encoded for

multichannel surround sound.

Notice that DVD discs do not always carry full multichannel

surround. To be sure that a disc is multichannel encoded

consult your dealer.

Most ordinary stereo tapes and discs can be replayed using

surround sound settings with good results. If the reproduction

is distorted in surround mode, switch to normal stereo mode.

The availabilty of the various surround sound modes described

depends on the number of speakers used and the incoming

sound information.

With surround sound on, you can switch through the different

surround modes. Note that the possibilities are related to

speaker setup defined in the receivers menu.

1 Press SURROUND ON/OFF to switch on the surround sound.

yThe surround mode in use is scrolled.

2 Press SURR. MODE repeatedly to listen to the different

surround modes (if available).

yThe surround mode in use is scrolled.

3 Press HALL to switch hall either on or off.

yHALL is displayed if hall is on.

4 Press SURROUND ON/OFF to switch off the surround

sound.

ySURROUND OFF is scrolled.

Note: Switching surround sound has no effect when using the

6 CHANNEL / DVD IN input.

HALL

The sound reproduction is enhanced and a slight echo is

added. This gives the impression of being in a large room.

SURROUND <PRO LOGIC>

The surround mode enables normal surround sound

reproduction with 4 or 5 speakers.

FRONT-3 STEREO <PRO LOGIC>

The surround sound is muted. 3 Stereo lets you listen to

surround sound without using the surround speakers.

STEREO

All sound is reproduced and played through the front left and

right speakers. This enables standard stereo reproduction.

Surround sound settings

Switching surround sound

About surround sound

19

English

TUNER

You can search for radio stations by scanning the frequency

band. You can also key in the frequency of a known radio

station. If an FM station is being broadcast and received in

stereo, = is shown.

Searching for radio stations

1 Turn SOURCE SELECTOR to select the tuner.

yTUNER is displayed.

2 Select a waveband by pressing TUNER AM/FM repeatedly.

yThe selected waveband is displayed.

3 Keep 1 or 2 pressed for approximately 1 second.

ySEARCH is displayed and the tuner tunes to a station

with sufficient strength.

4 Repeat this procedure until you find the desired station.

• To fine tune to a weak transmitter, briefly press 1 or 2 as

often as necessary for optimum reception.

Tuning to a radio station by frequency (with the remote

control only)

1 Press TUNER.

yTUNER is displayed.

2 Press FR. D..

y_ is displayed.

3 Use 1–0 to key in the frequency of a radio station.

Note: Only valid numbers within the frequency range of the

tuner can be keyed in.

You can switch the tuner to a lower search sensitivity, to

search for stations with a strong signal only (FM only).

1 Turn SOURCE SELECTOR to select the tuner.

yTUNER is displayed.

2 Press SENS. on the receiver.

yEither SENS HI or SENS LO is displayed for 5 seconds.

Note: While searching for radio stations, the actual sensitivity

is displayed. In this case, SENS LO means the tuner is

only looking for radio stations with a strong signal.

You may store up to 30 radio stations in the memory. The

receiver can select and program radio stations by itself or you

can choose them yourself.

Automatic programming

1 Choose * TUNER from the menu and press NEXT 2.

2 Choose AUTO INST and press NEXT 2.

yThe preset number where programming will start, the

waveband and AUTO are displayed.

3 Turn TUNER PRESET X to change the preset number where

programming should start.

4 Use TUNER AM/FM to switch to the desired waveband.

5 Press ENTER / OK to start programming.

yAUTO INST flashes and all available radio stations

are programmed, this may take a few minutes.

Programming is done when AUTO INST stops

flashing.

Manual programming

1 Choose * TUNER from the menu and press NEXT 2.

2 Choose MAN INST and press NEXT 2.

yA preset number, the waveband and the frequency are

displayed.

3 Turn TUNER PRESET X to change to the preset number

where the radio station should be stored.

4 Tune to the desired radio station (see “Searching for radio

stations”).

5 Press ENTER / OK to confirm your selection.

ySTORED is displayed briefly. The radio station is

programmed at the chosen preset number.

6 Select and store all desired radio stations this way.

Storing radio stations

Switching FM sensitivity

Tuning to radio stations

20

English

TUNER

1 Turn SOURCE SELECTOR to TUNER to select the tuner.

yTUNER is displayed.

2 Turn TUNER PRESET X to select a preset radio station.

yPRESET, the preset number and station are displayed.

After programming radio stations, you might want to change

their sequence. RESHUFFLE allows you to exchange the

positions of presets.

1 Choose * TUNER from the menu and press NEXT 2.

2 Choose RESHUFFLE and press NEXT 2.

yPRESET, a preset number and station are displayed.

3 Turn TUNER PRESET X to select a preset station.

4 Press ENTER / OK to confirm the selection.

yThe selected preset number <-> and a second preset

number are displayed.

5 Turn TUNER PRESET X to select the other preset station.

6 Press ENTER / OK to confirm the exchange.

yRESHUFFLED is displayed briefly and these two

preset numbers are swapped.

It is possible to assign a name to any of the preset radio

stations. RDS station names also can be overwritten.

1 Choose * TUNER from the menu and press NEXT 2.

2 Choose GIVE NAME and press NEXT 2.

yA preset radio station is displayed.

3 Turn TUNER PRESET X to select the preset to be renamed.

4 Press ENTER / OK to confirm your selection.

yThe existing name or ________ is displayed.

5 Turn TUNER PRESET X to select a letter and NEXT 2 or

1 PREV. to move to the next or previous position.

6 After you have entered the entire name, press ENTER / OK

to confirm.

ySTORED is displayed and the name is stored.

Note: If you want to use the transmitted RDS station name

again, simply clear the given name.

1 Use the menu option * TUNER, choose GIVE NAME.

yA preset radio station is displayed.

2 Turn X MENU NAVIGATOR to select the name to be

cleared.

3 Press ENTER / OK to confirm your selection.

4 Press 1 PREV. while the first letter is flashing.

y CL is flashing to the left of the station name.

5 Press ENTER / OK to clear the station name.

Or, if you have changed your mind,

press 1 PREV. to leave the station name as it is.

Clearing station names

Naming radio stations

Resorting stored radio stations

Tuning to stored radio stations

Seite laden ...

Philips FR 740 & FR740 Bedienungsanleitung

Dieses Handbuch ist auch geeignet für

Philips FR 740 & FR740 Bedienungsanleitung

in anderen Sprachen

Verwandte Papiere

Sonstige Unterlagen