Silvercrest SKWH 2000 A1 Operation And Safety Instructions

IAN 324120_1901

WALL-MOUNTED CERAMIC HEATER & FAN SKWH 2000 A1

WALL-MOUNTED CERAMIC HEATER & FAN

Operation and Safety Instructions

This product is only suitable for well

insulated spaces or occasional use.

IEGB

KERAMIK WANDHEIZLÜFTER

Bedienungs- und Sicherheitshinweise

Dieses Produkt ist nur für gut isolierte Räume oder

für den gelegentlichen Gebrauch geeignet.

ATDE CH

GB CY

CYNI

ΚΕΡΑΜΙΚΌ ΑΕΡΌΘΕΡΜΌ ΤΌΙΧΌΥ

Υποδείξεις χειρισμού και ασφαλείας

Το προϊόν είναι κατάλληλο μόνο για χρήση σε

καλά μονωμένους χώρους ή περιστασιακά.

CYGR

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

DE AT CH

Before reading, fold out the page with the images and familiarise yourself with all the features of the device.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες της

συσκευής.

GB IE NI

GR CY

CY

GB/IE/NI/CY Operating and Safety Instructions Page 5

GR/CY Υποδείξεις χειρισμού και ασφαλείας Σελίδα 21

DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 39

6

5

4

31 2

7

8

11

10

9

D

B

C

A

12 13

E

Πρόγραμμα

Δευτέρα

Παρα-

σκευή

Σάββατο

Κυριακή

P1

8:00-17:00 8:00-17:00

P2

18:00-7:00* 18:00-7:00*

P3

8:00-17:00

απενεργο-

ποίηση

P4`

18:00-7:00*

απενεργο-

ποίηση

P5

απενεργο-

ποίηση

απενεργο-

ποίηση

P6

ελεύθερα

ρυθμιζόμενη

λειτουργία

ελεύθερα

ρυθμιζόμενη

λειτουργία

Υπόδειξη: Οι ώρες με σήμανση * λήγουν

την επόμενη ημέρα.

Εύρος ρύθμισης ώρας

00-24 ώρα, ο χρόνος εκκίνησης πρέπει να είναι

πριν τον χρόνο λήξης.

GR

F

G

H

I

Program

Monday -

Friday

Saturday-

Sunday

P1

8am -5pm 8am -5pm

P2

6pm -7am* 6pm -7am*

P3

8am -5pm OFF

P4

6pm -7am* OFF

P5

OFF OFF

P6

Free mode Free mode

Please note: The times marked with* end on the sub-

sequent day.

Timing range 00-24 h, the start time

must be before the stop time.

GB

IE

NI

CY

Programm

Montag-

Freitag

Samstag-

Sonntag

P1

8:00-17:00 8:00-17:00

P2

18:00-7:00* 18:00-7:00*

P3

8:00-17:00 Aus

P4

18:00-7:00* Aus

P5

Aus Aus

P6

freier Modus freier Modus

Hinweis: Die mit * gekennzeichneten Uhrzeiten

enden am darauf folgenden Tag.

Zeiteinstellungs-

bereich 00-24 Uhr, die Startzeit muss vor der Stopp-

zeit liegen.

GB/IE/NI/CY

5

Table of contents

Introduction .................................................................................................................................... Page 6

Intended use ..................................................................................................................................... Page 6

Equipment ......................................................................................................................................... Page 6

Scope of delivery .............................................................................................................................. Page 6

Technical Data .................................................................................................................................. Page 7

Safety Instructions ..................................................................................................................... Page 8

Safety instructions for devices intended domestic purposes .......................................................... Page 8

Special safety instructions for heaters ............................................................................................. Page 8

Additional safety instructions for heaters ......................................................................................... Page 9

Additional safety instructions .......................................................................................................... Page 9

Information about batteries .............................................................................................................. Page 10

Before you start the device .................................................................................................. Page 11

Installation ...................................................................................................................................... Page 12

Starting up ...................................................................................................................................... Page 12

Control with aid of remote control unit ........................................................................................... Page 13

Explanation of the functions ............................................................................................................. Page 13

Maintenance, Cleaning, and Storage ........................................................................... Page 17

ROWI Electronics GmbH warranty ................................................................................. Page 17

Service ............................................................................................................................................... Page 18

Disposal ............................................................................................................................................ Page 18

Brief instruction for the remote control unit ................................................................. Page 19

6 GB/IE/NI/CY

WALL-MOUNTED CERAMIC

HEATER & FAN SKWH 2000 A1



 Introduction

Congratulations on the purchase of your

new fan heater. You have opted for a high

quality product. The operating instructions

are part of this product. They contain important infor-

mation on safety, usage and disposal. Familiarise your-

self with all operating and safety instructions before

you use the product. Use the product only as described

and only for the speciﬁed areas of use. When passing

on the product, please do not forget to hand over all

the necessary documents to the new user.



Intended Use

This device is only intended for heating of closed and

dry rooms during transitional periods.

The device is

not intended for use in special conditions, for examp-

le, in a corrosive or explosive area (dust, vapour or

gas). Do not use the device outdoors. Any other use

or modiﬁcation of the device is deemed to be an im-

proper use and means a considerable risk of acci-

dents. For damage caused by the improper use, no

liability will be accepted by us. This fan heater is only

intended for private use as a supplementary heater.



Equipment

Articles 1-13, as well as A-E are written on the front

fold-out side.

1

ON/OFF button

2

Oscillation button

3

Windows key

4

Timer button

5

OK button

6

Cancel button

7

Minus button

8

Plus key

9

Week timer button

10

Temperature button

11

Heating level key

12

Tab

13

Batterycompartment

A

Heating level display

B

Week timer display

C

Oscillation display

D

Temperature display

E

Air slot

F-I are given on the rear fold-out side.

F

ON/OFF button

G

Start/stop button

H

Fastening screws

I

Wall dowels



Scope of delivery

1 Wall-mounted ceramic heater & fan SKWH 2000 A1

2 Fastening screws

2 Wall dowels

1 Remote control (incl. button cell)

1 Operating Instructions

GB/IE/NI/CY

7



Technical data

Input voltage: 220-240 V

~

(alternating current)

Mains frequency: 50-60 Hz

Rated consumption: 2000 W

Heating level 1: 1000 W

Heating level 2: 2000 W

Protection class II

Temperature range:

18°C - 45°C

Timer: max. 8 hours

Dimensions: 57 x 12 x 19 cm (L x H x W)

Weight: 2,5 kg

Remote control

Battery supply: 3V (direct current) / CR2025

Information requirements for electric local

space heaters

Model identiﬁer(s): SKWH 2000 A1

Item Symbol Value Unit

Heat output

Nominal heat output P

nom

2.0 KW

Minimum heat output

(indicative)

P

min

1.0

KW

Maximum continuous

heat output

P

max,c

2.0 kW

Auxiliary electricity consumption

At nominal heat output

el

max

N/A kW

At minimum heat

output

el

min

N/A kW

In standby mode el

SB

0.00043

kW

Item Unit

Type of heat input, for electric storage local

space heaters only (select one)

manual heat charge control,

with integrated thermostat

[no]

manual heat charge control with room

and/or outdoor temperature feedback

[no]

electronic heat charge control with room

and/or outdoor temperature feedback

[no]

fan assisted heat output [no]

Type of heat output/room temperature control

(select one)

single stage heat output and no room

temperature control

[no]

Two or more manual stages, no room

temperature control

[no]

with mechanic thermostat room

temperature control

[no]

with electronic room temperature control [no]

electronic room temperature control plus

day timer

[no]

electronic room temperature control plus

week timer

[yes]

Other control options

(multiple selections possible)

room temperature control, with presence

detection

[no]

room temperature control, with open

window detection

[yes]

with distance control option [no]

with adaptive start control [no]

with working time limitation [yes]

with black bulb sensor [no]

ROWI Electronics GmbH

Augartenstrasse 3

76698 Ubstadt-Weiher, Germany

(Germany)

8 GB/IE/NI/CY



 Safety Instructions

Please read all

safety instructions and notes.

Failure to comply with the

safety instructions and precautions

may result in serious injury and/or

property damage.

FOR THE FUTURE, PLEASE KEEP

ALL SAFETY INSTRUCTIONS

AND NOTES IN A SAFE PLACE!

Danger to life by

electrical power!



Safety instructions for

devices intended for

domestic purposes

Q

This heater can be used by child-

ren aged from 8 years and abo-

ve and by physically, sensory

or mentally restricted persons if

they are supervised or given ins-

tructions on safe use and under-

stand the hazards involved as it

does not require any experience

or knowledge. This device is not

a toy for children to play with!

Cleaning and user maintenance

shall not be carried out by child-

ren without supervision.

Q

If the power supply cable of this

device is damaged it should be

replaced by the manufacturer

or by its customer service, or

a similarly qualiﬁed person, to

avoid danger.

Q

The device is only inten-

ded for indoor use.



Special safety instructions

for heaters

Q

To avoid

overheating of the

de-

vice, do not cover it.

Q

Do not install the heater directly

below a wall socket.

Q

The heater must not be used if

the ceramic ﬁeld is damaged.

Q

Do not use this heater together

with a program switch, a timer, a

separate remote control system,

or another device, which can au-

tomatically turn the heater oﬀ: it

may cause a ﬁre hazard when

the heater is covered or incorrec-

tly mounted.

Q

Never use the device in the di-

rect vicinity of a bath tub, a sho-

wer, or a swimming pool.

Q

The heater must not

be used in small rooms

inhabited

by people who cannot leave the

room themselves, unless they are

constantly supervised.

GB/IE/NI/CY

9



Additionally safety inst-

ructions for heaters

Q

Children under the age of 3 are

to be kept away unless they are

continually supervised.

Q

Children between the age of 3

and 8 are only allowed to turn the

device on or oﬀ if they are super-

vised or given instructions on safe

use and understand the hazards

involved, provided that the heater

has been placed or installed in its

intended normal operating positi-

on. Children between the age of

3 and 8 shall not plug in, regulate

and clean the heater or perform

user maintenance.

Q

Caution!

Some parts of the pro-

duct can become very hot and

cause burns.

Pay particular attention when chil-

dren and vulnerable people are

present.



Additional safety instruc-

tions

Q

If the mains cable or plug is dam-

aged, do not use the device! Do

not re-start the device before hav-

ing a new mains cable or plug

installed by an authorised spe-

cialist.

Q

Never open the housing of the

device. Touching the live cables

and connections and/or modify-

ing the electrical and mechanical

installation means danger to your

life by electric shock!

Q

Before you connect the device to

the mains, compare the electrical

connection parameters on the

nameplate (voltage and frequen-

cy) with the data of your electric

network. Make sure that all the

data match so that no damage

may occur to the device.

Q

Do not use extension cables or

power outlet strips.

Q

Make sure that the power sup-

ply cable is not damaged and

not laid on hot surfaces and /

or sharp edges.

Q

Make sure that the power cable

is not buckled or got jammed.

Q

Repair of electrical equipment

may only be carried out by ex-

perts who are specially trained

by the manufacturer. Improper

repair can cause considerable

danger for the device users.

Q

DANGER OF FIRE!

Never place the device

near or under curtains

or other combustible materials.

Q

Avoid combustible materials’

contacting the device.

Q

Before using the device, check

10 GB/IE/NI/CY

it for visible damage. If the de-

vice fell down or got damaged,

do not start it.

Q

If the power supply cable of this

device is damaged it should be

replaced by the manufacturer

or by its customer service or

a similarly qualiﬁed person,

to avoid danger.

Q

BEWARE OF HOT SUR-

FACES!

Q

Some parts of the product can

become very hot and cause

burns. Pay particular attention

when children and vulnerable

people are present.

Q

Repair of the device shall only be

done by authorised companies

qualiﬁed in this ﬁeld or by the af-

ter-sales service. Improper repair

can cause considerable danger

for the device users. Moreover, it

will void all warranty claims.

Q

Defective components may

only be replaced with original

spare parts. Only if original

spare parts are used, it is en-

sured that the security require-

ments are met.

Q

Protect the device

against hu-

midity and penetration of liquids.

Q

When disconnecting, pull the

power cable from the wall sock-

et by the power plug only, do

not jerk out the cable!

Q

Do not use the device in the vi-

cinity of open ﬂames.

Q

In the case of faults or during a

thunderstorm, pull out the con-

nector plug from the wall socket.

Q

Use the device only when the

power cable is completely run

out. Never wind the power ca-

ble around the device. Make

sure that the power cable does

not contact hot surfaces. Route

the cable so that nobody can

stumble over it.



Information about batteries

Incorrect use of batteries may

result in ﬁre, explosion, leakage

of dangerous substances, or

other hazard!

Q

Do not throw batteries into the

ﬁre and do not expose them to

high temperatures.

Q

Do not open, deform or short-cir-

cuit the batteries. Otherwise,

the contained chemicals can

leak out of them.

Q

Do not try to recharge batter-

ies. Recharging is only allowed

for batteries which are marked

as “rechargeable”. There is a

danger of explosion!

Q

Regularly check the batter-

ies. Leaking chemicals can

cause heavy damage to the

device. Dealing with dam-

GB/IE/NI/CY

11

aged or leaking batteries,

exercise a particular caution.

Risk of chemical burns! Wear

protective gloves.

Q

Chemicals escaping from a bat-

tery can cause skin irritation.

Q

In case of contact with skin,

rinse with much water. In case

of contact with eyes, do not rub

your eye, but rinse it with water

and immediately visit a doctor .

Q

Never let the batteries get into

the hands of children. If a small

child puts a battery into his

mouth, he can swallow it. If the

battery is swallowed, call a doc-

tor immediately.

Q

Never use diﬀerent battery

types together.

Q

When inserting the battery, pay

especial attention to the correct

polarity. Wrong polarity can

cause risk of bursting.

Q

If you do not use the device for

a long time, remove the batter-

ies from the device.



Before you start the device

REMOTE CONTROL:

HOW TO INSERT OR CHANGE THE BATTERY

The remote control unit is delivered together with a lit-

hium button cell. To enable the remote control, remove

the plastic tape that protrudes from the battery compart-

ment

13

(see Figure 1).

If the remote control battery needs to be replaced, in-

sert a new 3-volt lithium button cell. Pay attention to the

type of lithium button cell (CR2025).

Press the tab

12

on the battery compartment

13

of the remote control toward the centre. Now pull

out the battery compartment

13

.

(see Figure 2).

Remove the old battery.

Insert a new 3V-button-cell battery (type CR2025).

Pay attention to the correct polarity.

Push the battery compartment

13

back into the re-

mote control unit until the tab

12

snaps into place.

1

2

12 GB/IE/NI/CY



 Installation

Hang the device onto the wall. The device’s air outlet

should be at the bottom

E

Use the

dowels

I

and

screws

H

included in the delivery.

Please note: Make sure that the wall can

bear weights of at least 4.1 kg.

Drill two holes with a 6 mm drill and insert the sup-

plied wall dowels into them

I

.

Screw the fastening screws

H

into the wall dowels

I

. Each screw shall protrude to about 10 mm

H

.

PLEASE NOTE: When drilling, make sure that you

do not damage concealed power lines!

The distance between the holes must be 31.5 cm

(see Figure 3).

The distance to the ceiling and walls must be at

least 30 cm.

The distance to the ﬂoor must be at least 2m

(see

Figure 4).

Please note: If the speciﬁed distances can not be

maintained, the device may not be mounted.

Please note: If necessary, you will need a climbing aid

(e.g. a ladder) to carry out the installation

3

4

5

Place the heater onto the

fastening screws

H

(see Figure 5).

Make sure that the

fastening screws

H

are

straightly inserted into the holes

(see Figure 6).

Now move the heater to the right and then down

to the position .

A

Uninstall

Install

B



 Starting up

Connect the fan heater to a grounded and secured

socket. To supply the electric current to the device,

turn the ON/OFF switch

F

to the "I" position. The

device is now at the standby mode. Its display shows

the ambient temperature.

Now you can turn the fan heater ON and OFF, as

follows:

On the fan heater: Press the Start/Stop button

G

. The device starts. By pressing the start/stop

button again

G

, you can turn the OFF.

Please note: If necessary, a climbing aid is required to

press the ON/OFF button

F

or the start/stop button

G

on the device.

With the remote control unit: Press the ON/OFF

button

1

on the remote control unit. The unit starts.

To turn the unit OFF, press the ON/OFF button

1

on it once more.

6

GB/IE/NI/CY

13

Please note:

If you turn the unit oﬀ, the fan will still run 30 seconds.

Then the unit will switch oﬀ. A countdown is shown on the

display (only after heating function).

TURNING OFF

To turn the device oﬀ, please press the

ON/OFF button

1

on the remote control

unit.

To disconnect the fan heater from the power

supply,

F

set the ON/OFF switch to posi-

tion ‘ ‘.



Control with aid of remote

control unit

Please note: Before you completely shut down the de-

vice or disconnect it from the power supply, ﬁrst turn it

oﬀ with the aid of the remote control unit and wait be-

fore it stops to run. The display shows a 30-second af-

ter-run timer. All the device functions are managed with

the aid of the remote control unit. The respective symbol

lights up on the display when the function is activated.



Explanation of the functions

TEMPERATURE SETTING

When setting the temperature, please note

that the device does will not heat, if the desi-

red temperature is not higher than the ambi-

ent temperature. To enable heating, the set

temperature needs to be at least 1°C higher

than the ambient temperature. The latter is

automatically displayed when the device is

turned on. After successful temperature set-

ting, the symbol appears on the display. The

fan continues to run.

Please note:

The fan runs independently of the temperature setting.

Press the temperature button

10

once to adjust the

temperature.

Press the plus key

8

to increase the temperature.

Press the minus button

7

to reduce the temperature

(between 18 and 45°C)

After setting the desired temperature, press the OK

button

5

or simply wait for 5 seconds without

making any entries.

Please note:

You can cancel your entry by pressing the cancel

button

6

.

TIMER SETTING

The purpose of the timer is to automatically

turn oﬀ the ceramic fan heater.

With the aid of the timer, you can select the turn-oﬀ time

in hour increments. Then the wall-mounted ceramic fan

heater will switch oﬀ automatically.

Please note: As long as a weekly timer is activated,

the turn-oﬀ timer cannot be used. (See Chapter “De-

activation of the Week Timer)

Turn the device ON (see Starting). Press the timer but-

ton

4

repeatedly until you reach the desired number

of hours.

Example: If the device should automatically switch oﬀ

after 4 hours, press the timer button

4

until you see

"4H" on the display. Wait about 5 seconds. The infor-

mation is automatically transferred. Then the device will

be automatically turned oﬀ in 4 hours. If you want to

make sure that the timer entry has been transferred,

press the timer button

4

once more. Then ‘4H’ or your

entry will appear in the display.

By repeatedly pressing the timer button

4

, the timer

will be adjusted in 1-hour increments:

0H -1H -2H – 3H - 4H - 5H – 6H – 7H – 8H

OSCILLATION FUNCTION

To turn the device oscillation function on or

oﬀ, press the oscillation button

2

. If the

oscillation function is enabled successfully, it

will be shown on the display. The oscillation

function means that the blown air is distribu-

ted from the top to the bottom.

14 GB/IE/NI/CY

HEATING STEP ADJUSTMENT

By pressing the heating level button

11

,

you can adjust the desired heating level.

By each pressing the button, you will switch to

the next heating level.

Depending on the selected

heating level, you will see the respective value on

the display.

Press once: 1 heating level (1000 W)

Press twice: 2 heating level (2000 W)

Press thrice: Fan

SYSTEM TIME SETTING

Prior to use the week timer ﬁrst time, set the current time:

1. Select the ﬁrst heating level. The left symbol lights up

A

on the display . For details, refer to

Chapter

Heating Level Setting.

2. Press the shown week timer button

9

:

3.

Then the week day is shown on the display (see

the table). By pressing the plus

8

or minus

7

button, select the current day of the week:

01. Monday 02. Tuesday

03. Wednesday 04. Thursday

05. Friday 06. Saturday

07. Sunday

4.

Conﬁrm your selection by pressing the OK

button

5

.

5. Now the display now shows the number of hours

(00). By pressing the plus

8

and minus

7

but-

tons, you can adjust the desired number of hours

(00-23).

6.

Conﬁrm your selection by pressing the OK

button

5

.

7. The display now shows the number of minutes

(00). By pressing the plus and

8

minus buttons

7

, you can adjust the desired number of minutes

(00-59)

.

8. You can save your settings by pressing the OK but-

ton

5

and then exit the menu.

9. As soon as you have set the system time, "P1" appe-

ars in the display.

10. Wait 10 seconds without pressing any key. Then

the system settings will be accepted by the sys-

tem. The ambient temperature is shown on the

display. If necessary, you can continue selection

of programs: P1, P2... P6. For more information,

see Chapter ‘Week Timer”.

Please note: to reset the system time, you have to

turn oﬀ the device and disconnect it from the po-

wer supply.

WEEKLY TIMER

The purpose of the week timer is to auto-

matically switch the wall-mounted ceramic

fan heater on and oﬀ at speciﬁc times. To

set the week timer, you have 5 pre-set pro-

grams available. Moreover, you have also

a program to be set manually. As soon as

the function is activated, the device auto-

matically switches on or oﬀ according to the

respective time table.

Please note:

it is not possible to start the week timer,

as long as the device is at the fan mode.

Please note:

To adjust the week timer, you have to set

the system time ﬁrst (see ‘System Time Setting’)

SETTING THE TIMER PROGRAMS, 1-5 (PRE-SET

PROGRAMS)

1. Turn on the device (see ‘Starting’).

2.

Select the ﬁrst or the second heating level. To do

so, press the heating level button

11

. The

A

sym-

bol lights up on the display.

See Chapter “Hea-

ting Levels Setting”. Alternatively, you can select

a desired temperature (see chapter “Temperature

Setting”).

Please note: The wall-mount ceramic fan heater will

be turned ON depending on the selected program and

run the last heating level or temperature you selected.

GB/IE/NI/CY

15

3. Press the week-timer button

9

:

4. Then the timer program is shown on the display.

With each pressing the button

9

, you will switch

to the next program - P1-P2-P3-P4-P5-P6-OFF. (See

Program Table on the fold-out rear side)

5. Conﬁrm your selection by pressing the OK

button

5

.

6.

Depending on the program selected as descri-

bed in Item 4 and depending on the time (day

and time), the week timer indicator

B

lights up

or blinks in the display.

If values

A

and

B

are lit continuously, the selected

program is active or the device turns oﬀ automatically.

If values

A

and

B

are ﬂashing, the selected pro-

gram is not active. Then the device switches oﬀ after

30 seconds again. In the meantime, the fan runs until

the standby mode. Values

A

and

B

continue to

blink until the program automatically intervenes and

turns the device on.

ADJUSTMENT OF THE MANUAL

TIMER PROGRAM (P6)

1. Turn on the device (see Device Starting).

2. Select the ﬁrst or the second heating level. To do

so, press the heating level key

11

. The symbol

A

lights up on the display. See Chapter “Heating Le-

vel Setting”. Alternatively, you can select a desired

temperature (see chapter “Temperature Setting”).

Please note: The wall-mount ceramic fan heater will

be turned ON depending on the selected program and

run the last heating level or temperature you selected.

3. Press the shown week-timer button

9

:

4. Then the timer program is shown on the display.

Press and hold the week timer button

9

until "P6"

appears in the display.

5. Conﬁrm your selection by pressing the OK

button

5

.

6. Now the number of the respective day of the week

is ﬂashing (see the table). By pressing the plus

8

or minus

7

button, you can set the ﬁrst day of the

week which the timer should be set for.

01. Monday 02. Tuesday

03. Wednesday 04. Thursday

05. Friday 06. Saturday

07. Sunday

7. Conﬁrm your selection by pressing the OK

button

5

.

8. The number of the start time hours appears on the

display. You can adjust it by pressing the plus or

8

minus button

7

.

Please note: Please note that the start time must be

before the end time and that only hours (no minutes)

can be set. The start time and end time must relate to

the same day.

9. Conﬁrm your selection by pressing the OK

button

5

.

10. The number of the end time hours appears on the

display. You can adjust it by pressing the plus or

8

minus button

7

.

11. After 5 seconds, you will automatically switch to

the next week.

12. Now you can set the start and end times for each

day of the week one after another, as described in

items 8-10.

Please note: If you want to disable the timer for a day of

the week, select start and end time "00".

16 GB/IE/NI/CY

13. Once you have set all 7 days of the week, the

week timer is active. Depending on the function,

the indicators

A

and

B

light or blink.

If values

A

and

B

are lit continuously, the selected

program is active or the device turns oﬀ automatically.

If values

A

and

B

blink, it means that the selected

program is not yet in use. Then the device switches oﬀ

after 30 seconds again. In the meantime, the fan runs

until the standby mode. Values

A

and

B

continue

to blink until the program automatically intervenes

and turns the device on.

DEACTIVATION OF THE WEEKS TIMER

You can disable all the week timers, by pressing the

week timer button

9

again, after P6 is shown. Then

the reading in the display extinguishes. Alternatively,

you can use the week timer button

9

and then immedi-

ately press the cancel button

6

. The weekly timer can

also be disabled by once pressing the ON/OFF button,

while the value

B

blinks.

DETECTION OF OPEN WINDOWS

These are repeated measurement cycles. Each of them

will run 10 minutes. For each cycle, the following measure-

ments will be made: a start measurement, a ﬁrst compari-

son measurement after 5 minutes and another comparison

measurement after 10 minutes. If one of the two compari-

son measurements is more than 8°C lower than the start

measurement, the device will detect it as an open window

and automatically switch oﬀ.

1. Turn on the device (see ‘Starting’)

2. Select one of the two heating levels (see ‘Heating

Level Setting’).

Please note:

The window test can only be carried

out when a heating level is selected, not in the fan

setting mode.

3. Press the window key

3

. The temperature display

D

on the display starts to blink :

4. The ﬁrst measuring cycle the window measurement

starts after 1 minute.

5. The ﬁrst comparison measurement is carried out

after more 5 minutes. If the measured temperature

is more than 8°C below the start measurement, the

device turns oﬀ and the window check is comple-

ted. If this is not the case, the device will continue to

heat and the test will go on.

6. The second comparison measurement is made10

minutes after the start measurement. If the measured

temperature is more than 8°C below the start mea-

surement, the device turns oﬀ and the window check

is completed. If this is not the case, the second com-

parison measurement will be taken as a new start

measurement and the new measurement cycle will

start and run as described in steps 4 and 5.

7. As far as you do not ﬁnish the window test by

pressing the window button

3

, repeat steps 4

and 5 until you see a temperature drop of 8°C

within a cycle.

As soon as the device detects an open window, it stops

to heat. An audible alarm will sound for 5 seconds and

the fan will run 30 seconds till the standby mode. The

temperature indicator

D

and the LED "OF" are shown

blinking on the display.

While LED "OF" blinks, the swit-

ched-oﬀ device is at the “open-window” mode.

Please note:

when the window test is completed, the

device must be started manual, if desired. To do so,

press the on/oﬀ button

1

on the remote control unit to

turn the device oﬀ. The heater switches oﬀ. The blinking

temperature indicator

D

on the display and the indica-

tor "OF" will be deleted.

SAFETY SHUT-DOWN

If the measured room temperature 51°C, the device swit-

ches oﬀ automatically. The fan runs 30 seconds before it

turns oﬀ. A countdown is shown on the display.

GB/IE/NI/CY

17



 Maintenance, Cleaning

and Storage

Always disconnect the power plug when the device

is not in use and before any cleaning or in the

event of operating faults!

Clean the device only when it is turned OFF and

in a cooled condition.

Ensure that no moisture penetrates into the device

in order to avoid irreparable damage.

Clean the housing with a soft dry cloth only. Do not

use aggressive and/or abrasive cleaning agents.

Remove dust deposits from the protective grille

with a vacuum cleaner.

Store the device in a dry room.



 ROWI Electronics GmbH warranty

Dear Customer,

This appliance has a 3-year warranty valid from the

date of purchase. If this product has any faults, you,

the buyer, have certain statutory rights. Your statutory

rights are not restricted in any way by the warranty

described below.

Warranty conditions

The validity period of the warranty starts from the

date of purchase. Please keep your original receipt in

a safe place. This document will be required as proof

of purchase.

If any material or production fault occurs within three

years of the date of purchase of the product, we will

either repair or replace the product for you at our

discretion. This warranty service is dependent on you

presenting the defective appliance and the proof of

purchase (receipt) and a short written description of

the fault and its time of occurrence.

If the defect is covered by the warranty, your product

will either be repaired or replaced by us. The repair

or replacement of a product does not signify the be-

ginning of a new warranty period.

Warranty period and statutory claims for defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to re-

placed and repaired components. Any damage and

defects present at the time of purchase must be re-

ported immediately after unpacking. Repairs carried

out after expiry of the warranty period shall be sub-

ject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected me-

ticulously prior to delivery.

The warranty covers material faults or production faults.

The warranty does not extend to product parts subject

to normal wear and tear or fragile parts such as switch-

es, batteries, baking moulds or parts made of glass.

The warranty does not apply if the product has been

damaged, improperly used or improperly main-

tained. The directions in the operating instructions for

the product regarding proper use of the product are

to be strictly followed. Uses and actions that are dis-

couraged in the operating instructions or which are

warned against must be avoided.

This product is intended solely for private use and not for

commercial purposes. The warranty shall be deemed

void in cases of misuse or improper handling, use of

force and modiﬁcations/repairs which have not been

carried out by one of our authorised Service centres.

Warranty claim procedure

To ensure quick processing of your case, please ob-

serve the following instructions:

Please have the till receipt and the item number

(IAN 324120_1901) available as proof of

purchase.

You will ﬁnd the item number on the type plate,

an engraving on the front page of the instructions

(bottom left), or as a sticker on the rear or bottom

of the appliance.

18 GB/IE/NI/CY

If functional or other defects occur, please contact

the service department listed either by telephone

or by e-mail.

You can return a defective product to us free of

charge to the service address that will be pro-

vided to you. Ensure that you enclose the proof

of purchase (till receipt) and information about

what the defect is and when it occurred.

NOTICE: At www.

lidl-service.com you can

download this manual

as well as many other

manuals, product videos

and software. This QR

code will take you directly

to the Lidl service page

(www.lidl-service.com)

and allow you to open

your operating instruc-

tions simply by entering

the article number (IAN

324120_1901).



 Service

If any problems occur during use of your ROWI

Electronics product, please proceed as follows:

Contact us

You can contact the service team of ROWI Electronics at:

ROWI Electronics GmbH

Augartenstr. 3

76698 Ubstadt-Weiher, Germany

Ld-ser[email protected]

Service hotline: +800 7694 7694

(free call from a German landline)

IAN 324120_1901

Most problems can be ﬁxed with competent technical

advice from our service team.



 Disposal

The device packaging is made of environ-

mentally friendly materials that you can

dispose of at your local recycling centres.

Do not dispose of the product with the

regular household garbage! Bring

it to a municipal collection points for

recycling! In case of doubt, ask your

municipality or city administration how to

dispose of the old device.

Batteries must be recycled in accordance

with Directive 2006/66/EC and must

not be disposed of with household waste.

Every consumer is legally obliged to hand

in all batteries/rechargeable batteries at

a collection point in their municipality/ dis-

trict or in a shop. This obligation aims to

ensure that batteries are disposed of in an

environmentally friendly manner. Only re-

turn batteries when they have been ful¬ly

discharged. Batteries must be removed

from the appliance before disposal.

Observe the marking of the packaging

materials for waste separation, which are

marked with abbreviations and numbers

with following meaning: 1–7: plastics/

20–22: paper and ﬁbreboard/80–98:

composite materials.

04

PE-LD

GB/IE/NI/CY

19

Control system Key Action

Turning ON/OFF

By pressing the key once, the device is

turned ON. By pressing the key once

more, the device is turned OFF.

Please note: The fan continues to run

for 30 seconds. The running countdown

is visible in the display for 30 seconds.

Level setting

Press once: 1. heating level (1000 W).

Press twice: 2. heating level (2000 W).

Press thrice: Fan

Timer Setting

With each PRESSING the key, the time

period increases by 1hour (0H, 1H,

2H... 8H) Please note: You cannot use

this timer when the week timer is active.

Oscillation ON/OFF

By pressing the key once, the oscillation is

enabled. By pressing the key once more,

the oscillation is disabled.

Temperature setting

Press once to start with the temperature

setting.

You can only set the temperature be-

tween 18°C and 45°C.

After setting the desired temperature,

press the OK button or simply wait for

5 seconds without making any entries.

Detection of open win-

dows

See Chapter Open Window Detection

Weekly timer

Select one of the 6 programs.

(P1, P2... P6)

Cancel

Temperature and timer settings will be

cancelled.

BRIEF INSTRUCTION FOR THE REMOTE CONTROL UNIT:

Seite laden ...

Silvercrest SKWH 2000 A1 Operation And Safety Instructions

Dieses Handbuch ist auch geeignet für

Silvercrest SKWH 2000 A1 Operation And Safety Instructions

in anderen Sprachen

Verwandte Papiere

Sonstige Unterlagen