Creality 3D Print Mill and Infinit-Z Benutzerhandbuch

3DPrintMill

User Manual • Uživatelský manuál •

Užívateľský manuál • Használati utasítás •

Benutzerhandbuch

2

Dear customer,

The product user guide contains product features, how to use, and the operating

procedure. Read the user manual carefully to get the best experience and avoid

unnecessary damage. Keep this manual for future reference. If you have any questions

or comments about the device, please contact the customer line.

✉ www.alza.co.uk/kontakt

✆ +44 (0)203 514 4411

Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

3

Notes

• Do not use the printer any way than described in order to avoid personal injury or

property damage.

• Do not place the printer near any heat source or explosive objects. We suggest

placing it in a well-ventilated, low-dust environment.

• Do not expose the printer to violent vibration or any unstable environment, as this

may cause poor print quality.

• Before using experimental or exotic filaments, we suggest using standard filaments

such as ABS or PLA to calibrate and test the machine.

• Do not use any other power cable except the one supplied. Always use a grounded

three-prong power outlet.

• Do not touch the nozzle or printing surface during operation as they may be hot

keep hands away from machine while in use to avoid burns or personal injury.

• Do not wear gloves or loose clothing when operating the printer. Such clothes may

become tangled in the printer moving parts leading to burns, possible bodily injury,

or printer damage.

• When cleaning debris from the printer hotend, always use the provided tools. Do

not touch the nozzle directly when heated. This can cause personal injury.

• Clean the printer frequently. Always turn the power off when cleaning, and wipe

with a dry cloth to remove dust, adhered printing plastics or any other material off

the frame, guide rails or wheels. Use glass cleaner or isopropyl alcohol to clean the

print surface before every print for consistent results.

• Children under 10 years of age should not use the printer without supervision.

• This machine is equipped with a security protection mechanism. Do not manually

move the nozzle and printing platform mechanism manually while booting up,

otherwise the device will automatically power off for safety.

• Users shall comply with related nation and region’s laws, regulations and ethical

codes where the equipment or produced prints by it is used, and users of our

product shall not use a foresaid products to print any end-use products, objects,

parts or components or any other physical prints that violate the national regional

4

laws, regulations and ethical codes where herein referred product and produced

prints by it is located.

Introduction

1 X motor

2 Nozzle kit

3 Printing platform

4 Bed leveling nut

5 Belt tensioning

screw

6 Manual power

switch

7 X axis limit switch

8 Extruder

9 Y motor

10 Material rack and

material tube

11 Knob screen

12 Knob

13 Storage card slot

and USB socket

14 Y-axis limit

adjustment

component

15 Z axis belt motor

16 Power cable

connection

































5

Parameters

Model

3DPrintMill

Print size

Infinite length *200*170mm

(length*width*height)

Moulding technology

FDM

Number of nozzle

1

Layer thickness

0.1mm-0.4mm

Nozzle Diameter

Standard 0.4mm

XY axis precision

±0.1mm

Filament

PLA/TPU/PETG

File Format

STL/OBJ/AMF

File transfer

Storage card

Compatible slicing software

CrealityBelt

Power specification

Input:100-120/200-240V 50/60Hz Output:

24/14.6A

Total Power

350W

Hotbed temperature

0-100°C

Nozzle temperature

0-240°C

Resume printing function

Yes

Filament sensor

Yes

Dual z-axis screws

No

Language switch

English

Computer operating system

Windows XP/Vista/7/10

Print Speed

⩽180mm/s,30-60mm/s normally

6

Parts List

1 X/Y axis belt

assembly x1

2 Bottom

belt

assembly x1

3 Display

kit x1

4 Spool holder

x1

5 Filament x1

6 Profile bracket 1

x1

7 Profile bracket 2 x1

Accessory tool list

8 Storage card and card

reader x1

9 Diagonal pliers x1

10 Cable tie x 10

11 Needle x 1

12 Blue line claw

x 2

13 Pneumatic connector

x 2

14 Power cord x 1

15 Wrenches and

screwdrivers x 1

16 M5T nuts x 6

17 Photoelectric switch

line x 1

18 Hexagon socket flat

round head screw M5X8

x 6

19 Hexagon socket flat

round head screw

M5X12 x 6

20 Hexagon socket flat

round head screw

M5X18 x 10

21 Hexagon socket

head spring washer

combination screw

M5X45 x4

22 Hexagon socket

head spring washer

combination screw

M5X12 x 4

23 Teflon tube x 1

24 Nozzles x 2

25 Socket wrench

x 1

26 Feeler x 1

7

*Tips: the above accessories are for reference only, please refer to the physical

accessories !

Install the Profile Support Frame

2 Bottom belt

assembly x 1

6 Profile bracket 1

x 1

7 Profile bracket 2

x 1

19 Hexagon socket

flat round head

screw M5X12 x 4

Step: Install the profile support 1 and profile support 2 to the bottom of machine

with four hexagon flat head screws M5x12 (As shown in the figure above).

8

Install X/Y Axis Belt Assembly

1 X/Y axis belt

assembly x 1

20 Hexagon socket

flat round head

screw M5X18 x 8

22 Hexagon socket

head spring washer

combination screw

M5X12 x 2

21 Hexagon socket

head spring washer

combination screw

M5X45 x2

Install with M5 * 45 socket head cap

screws with spring washer.

9

Install the Spool Holder

4 Spool holder x 1

16 M5T nuts x 2

18 Hexagon socket flat

round head screw M5X8 x 2

10

Install the Display

16 M5T nuts M5 T x 2

18 Hexagon socket flat round head screw

M5X8 x 2

Step: Lock the display assembly with two M5X8 flat head screws and two M5 T-nuts,

as shown in the figure above;

11

Cable Connection

14 Power cord x 1

Connect the broken

detection line as shown in

Figure A .

Insert the Teflon tube

into the pneumatic

connector (also insert the

blue wire clamp)

Caution

• Select the correct

input voltage match

your local power.

(115/230V)

• Damage can occur if

voltage is set

correctly.

• Connect the power

cord to turn the

power switch on.

Do not connect or

disconnect the cables when

the machine is powered on

After the display is

installed, please

connect the display

cable.

Connect the Y-axis limit

line.

12

Levelling

1. First move the X axis to the contact part between the nozzle and the belt (slightly

press the nozzle onto the belt).

2. Push the two limit switches against the X sliding block to lock the limit;

3. Press back on the screen to get the printer back to the origin; adjust the Y axis end-

stop adjusting screw according to the position of the nozzle relative to the belt after

back to the origin in order to make sure the nozzle contacting with the belt rightly; then

tighten the Y axis end-stop screw, leveling finished;

4. if there is any seam or over contact between the nozzle and the belt, adjust the

leveling nut slightly.

A Y axis end-stop

adjusting screw

B Y axis end-stop

adjusting the screw

13

Preheating

Method 1

Method 2

The nozzle is too far away from the

platform, so the consumables can

not adhere to the platform.

The even filament adheres right on

the platform.

The nozzle is too close to the

platform, the consumables are not

extruded enough, and the nozzle

outlet is damaged. Causes a plug

and scratches the belt.

Notes: The UI information is only for reference, the

actual UI may be different.

Notes: The UI information is only for reference, the

actual UI may be different.

14

When you want the temperature to rise, hang the filament over the filament

holder.

For smoother printing, the end of the filament

should be placed as shown above.

15

Load Filament

When the current temperature reaches the target temperature, press and hold the

spring of the extruder and insert the consumables into the charging detection hole one

by one,then insert the consumables into the small hole of the extruder until the nozzle

position.

Tips: How to Replace the Filament ?

Withdrawing the filament quickly and feeding the new filament after nozzle

preheated and filament pushed a little forward.

16

Start Printing

1. Double click to install the software.

2. Double click to open the software.

3. Select language→c



of prints to complete the setting.

5. Generate G-code, and save the gcode file to storage card.

6. Insert the storage card→print



printed.

4. Open the file in turn→select

the file

17

Circuit Wiring

File names must be Latin letters or numbers, not Chinese

characters or other special symbols.

Notes: For details on the software instructions, please

refer to the slicing software manual in the storage card!

X-axis

motor port

Y-axis

motor port

Z-axis

motor port

E-axis

motor port

Storage- card

slot

Nozzle fan

Motherboard

fan

Power input

Hot bed

wire port

Heating

pipe

interface

Controllable

nozzle fan

X axis limit

switch

Hot bed

thermal

Nozzle

thermistor

Broken

material

detection

Y axis limit

12864

screen

Micro USB

port

18

Trouble-shooting

Change the file name to English and

number format

1. Wipe Storage-card

2. Format Storage-card

3- Replace Storage-card

1. Move model position and slice again

2. Using repair software to repair the

model

1. Reconnect the circuit

2. Check by substitution

1. Reconnect the circuit

2. Check by substitution

1. Reconnect the circuit

cables

1. Reconnect the circuit

1. Reconnect the circuit and lock the

screws of thermistor

1. Slice again

2. Adjust the tension of the synchronous

belt

1. Fasten the coupling

1. Remove surface detects of filaments

2. Replace filament

1. Reconnect circuit

2. Check by substitution

E motor

Filament

Others

Coupling

Slicer/Sync

hronous

belt

Thermisto

r

Heat

tube

Thermisto

r

Hot bed

Limit

switch

Slicer

File

naming

Storage

card

Printing when

filament push

Heat the

nozzle

Heat the

hot bed

Return

“Home“

Play by

memory card

Seal

Problem

Resolved

Component

damage, replace

continuously

Unknown

malfunction

, please

contact the

after-sales

Start

Finish

Other

documents

are printed

normály or

not

Display error

codes or not

File

identification

or not

Print or

not

Beyond

“Home“

The display of

temp is

normal or not

Hot bed is

heated or not

The nozzle is

heated or not

The display of

humidity is

norma lor not

Dislocation

or not

Filament-

push or

not

The E motor

rotates or not

The gear

rotates or not

The filament is

norma lor not

Process result

Shaft

motor

Workflow

Fault diagnosis

Fault cause

Fault handling

Result

feedback

Y/N

19

Vážený zákazníku,

Uživatelská příručka k výrobku obsahuje funkce výrobku, návod k použití a postup

obsluhy. Přečtěte si pozorně uživatelskou příručku, abyste získali co nejlepší zkušenosti a

předešli zbytečným škodám. Tento návod si uschovejte pro budoucí použití. Máte-li

jakékoli dotazy nebo připomínky k zařízení, obraťte se na zákaznickou linku.

✉ www.alza.cz/kontakt

✆ +420 255 340 111

Dovozce Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

20

Poznámky

• Tiskárnu nepoužívejte jinak, než je popsáno, aby nedošlo ke zranění osob nebo

poškození majetku.

• Tiskárnu neumisťujte do blízkosti zdrojů tepla nebo výbušných předmětů.

Doporučujeme ji umístit do dobře větraného prostředí s nízkým obsahem prachu.

• Nevystavujte tiskárnu silným vibracím nebo jakémukoli nestabilnímu prostředí,

protože to může způsobit zhoršení kvality tisku.

• Před použitím experimentálních nebo exotických filamentů doporučujeme použít

standardní filamenty, jako je ABS nebo PLA, pro kalibraci a otestování stroje.

• Nepoužívejte jiný napájecí kabel než ten, který je součástí dodávky. Vždy používejte

uzemněnou tříkolíkovou zásuvku.

• Během provozu se nedotýkejte trysky ani tiskového povrchu, protože mohou být

horké, během provozu držte ruce mimo stroj, abyste se vyhnuli popálení nebo

zranění.

• Při obsluze tiskárny nenoste rukavice ani volný oděv. Takové oblečení se může

zamotat do pohyblivých částí tiskárny, což může vést k popálení, možnému zranění

nebo poškození tiskárny.

• Při čištění nečistot z horkého konce tiskárny vždy používejte dodané nástroje.

Nedotýkejte se přímo zahřáté trysky. Mohlo by to způsobit zranění osob.

• Tiskárnu často čistěte. Při čištění vždy vypněte napájení a otřete suchým hadříkem

prach, nalepené tiskové plasty nebo jiný materiál z rámu, vodicích lišt nebo koleček.

Před každým tiskem použijte čistič skla nebo izopropylalkohol k očištění tiskového

povrchu, abyste dosáhli konzistentních výsledků.

• Děti mladší 10 let by neměly tiskárnu používat bez dozoru.

• Tento stroj je vybaven bezpečnostním ochranným mechanismem. Při spouštění

zařízení ručně nepohybujte tryskou a mechanismem tiskové plošiny, jinak se

zařízení z bezpečnostních důvodů automaticky vypne.

• Uživatelé musí dodržovat zákony, předpisy a etické kodexy příslušného státu a

regionu, kde se zařízení nebo jím vyrobené výtisky používají, a uživatelé našeho

produktu nesmí používat uvedené produkty k tisku jakýchkoli konečných produktů,

Seite laden ...

Creality 3D Print Mill and Infinit-Z Benutzerhandbuch

Dieses Handbuch ist auch geeignet für

Creality 3D Print Mill and Infinit-Z Benutzerhandbuch

in anderen Sprachen

Verwandte Papiere

Sonstige Unterlagen