Parkside PRTA 20-Li A1 Translation Of The Original Instructions

CORDLESS GRASS TRIMMER PRTA 20-Li A1

AKKU-RASENTRIMMER

Originalbetriebsanleitung

CORDLESS GRASS TRIMMER

Translation of the original instructions

I A N 3110 4 6

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions

of the device.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit

allen Funktionen des Gerätes vertraut.

GB / IE / NI Translation of the original instructions Page XX

DE / AT / CH Originalbetriebsanleitung Seite XX

4

19

1 2 3

4

6

7

11

15

17

16

18

12

1314

8

9

10

5

19 20

16

19

10

12

20

14

1321

22

4

IE NIGB

Content

Introduction .................................4

Intended purpose .........................5

General description ......................5

Extent of the delivery....................... 5

Overview ...................................... 5

Functional description ..................... 5

Technical data .............................. 6

Safety instructions ........................6

Symbols and icons .......................... 6

General safety instructions for

power tools.................................... 7

Additional safety instructions .......... 10

Residual risks ............................... 11

Assembling instructions ..............11

Operation ..................................12

Turning on and off ........................ 12

Trimmer settings ............................ 13

Manner of operation .................. 13

Cutting grass................................ 13

Vertical cut / lawn edge

trimming ...................................... 14

Introduction

Congratulations on the purchase of your

new device. With it, you have chosen a

high quality product.

During production, this equipment has

been checked for quality and subjected to

a nal inspection. The functionality of your

equipment is therefore guaranteed.

Translation of the original

EC declaration of conformity ......35

Exploded Drawing .....................37

Cleaning and maintenance ......... 14

Cleaning ..................................... 14

General maintenance .................... 14

Replacing the cutting insert ............ 14

Storage ......................................15

Disposal and protection

of the environment.....................15

Replacement parts/Accessories ..15

Trouble shooting ........................16

Guarantee .................................17

Repair Service ............................18

Service-Center ............................18

Importer .................................... 18

The operating instructions constitute

part of this product. They contain

important information on safety, use

and disposal.

Before using the product, familiarise

yourself with all of the operating

and safety instructions. Use the

product only as described and for

the applications specied. Keep this

manual safely and in the event that

the product is passed on, hand over

all documents to the third party.

5

IE NIGB

- Battery

- Charger and rechargeable battery

operating instructions

- Instruction Manual

Overview

1 Top handle

2 On/Off switch

3 Switch lock

4 Box for cutting inserts

5 Auxiliary handle

6 Handle rod

7 Lock of handle rod adjustment

8 Threaded bush

for length adjustment

9 Telescopic shaft

10 Motor head

11 Bar for tilt angle adjustment

12 Protective cover

13 Cutting insert

14 Cutting disk

15 Spacer bow (ower guard)

16 Distance roller

17 Battery

18 Battery charger

19 Screws for protective cover

20 Screws for distance roller

21 Screw, nylon blade

22 Pin, nylon blade

23 Handle holder

24 Handle screw

Functional description

The trimming assembly of the manually

controlled, portable, battery-operated

lawn trimmer consists of a system of plastic

knife/cutting insert.

The appliance also features a pivoting mo-

Intended purpose

The appliance is solely intended for cutting

grass and weeds in the garden and for

edge trimming. Any other use that is not

specically approved in these Instructions

can result in damage to the trimmer and

give rise to serious danger for the user.

Do not use the appliance to trim hedges or

bushes. The appliance must only be used

by adults. Young people aged 16 and

over may only use the trimmer under adult

supervision.

The user or operator is responsible for ac-

cidents causing injury to other people or

damage to property.

The manufacturer cannot be held liable

for damage when the trimmer is not used

in conformity with its intended purpose or

due to incorrect operation.

This equipment is not suitable for commer-

cial use. Commercial use will invalidate the

guarantee.

General description

The illustration of the most im-

portant functional components

can be found on the front and

the back fold-out pages.

Extent of the delivery

Carefully unpack the trimmer and check

that it is complete:

- Battery-operated lawn trimmer

- Nylon blade

with one srew (left-hand thread)

- Protective cover with two screws

- Distance roller with two screws

- Auxiliary handle

- 20 Cutting inserts

- Battery charger

6

IE NIGB

tor head, adjustable aluminium telescopic

shaft, and a spacer bow. A hood covering

the cutting device protects the user.

Refer to the following descriptions for a

functional description of the controls.

Technical data

Cordless Grass Trimmer

.................................PRTA 20-Li A1

Motor voltage (U) ..................... 20 V

Idling speed ...............8000 min

-1

(rpm)

Protection Class ............................... III

Protection category .......................IPX0

Runtime ............................ ca. 45 min*

Cutting circle ..........................250 mm

Weight (without battery charger) 2.15 kg

Sound pressure level

(L

pA

) ............... 77.3 dB (A), K

pA

= 3 dB

Sound power level (L

WA

)

guaranteed .......................96 dB (A)

measured .. 89.8 dB (A); K

WA

=2.39 dB

Vibration (a

h

)

upper handle . 2.76 m/s

2

; K=1.5 m/s

2

additional

handle .......... 3.46 m/s

2

; K=1.5 m/s

2

* The actual runtime under load of a fully char-

ged battery depends on how you work and on

the load put on the trimmer during operation.

Noise and vibration values have been

determined according to the standards and

regulations mentioned in the declaration of

conformity. The vibration and noise meas-

uring processes in accordance with EN

50636-2-91, were completed successfully.

Noise and vibration values have been

determined according to the standards and

regulations mentioned in the declaration of

conformity.

The stated vibration emission value was

measured in accordance with a standard

testing procedure and may be used to com-

pare one power tool to another.

The stated vibration emission value may

also be used for a preliminary exposure

assessment.

Warning: The vibration emission

value may differ during actual use

of the power tool from the stated

value depending on the manner in

which the power tool is used.

Try to keep the exposure to vibra-

tions as low as possible. Examples

of measures to reduce vibration

exposure are the wearing of gloves

when using the tool and limiting the

working hours. For this purpose all

parts of the operating cycle have to

be considered (for example, times

when the electric tool is switched

off and times when it is switched on

but running without any load).

Safety instructions

Ensure that the safety instructions

are observed when operating the

trimmer.

Symbols and icons

Symbols on the trimmer

WARNING!

Carefully read these Operat-

ing Instructions.

Wear goggles

and ear defenders.

7

IE NIGB

After turning off the ap-

pliance, the cutting disk

will keep revolving for a

couple of seconds. Keep away

from your hand and feet.

Do not expose the trimmer to

moisture. Do not work when

it is raining and do not cut

wet grass.

Keep by-standers well

away. They could be

injured by ung out

objects.

Danger due to materials

blown out of machine!

Remove persons in the vicini-

ty from the danger area.

Remove the battery prior to

servicing the appliance.

Noise level rating L

WA

in dB

Electrical appliances must

not be disposed of with the

domestic waste.

Cutting circle

Parkside X 20 V TEAM.

Symbols in the manual

Warning symbols with

information on damage

and injury prevention.

Warning symbols with

information on the pre-

vention of personal injury

caused by electric shock.

Instruction symbols with infor-

mation on preventing damage.

Carefully read through the

user manual

Help symbols with information

on improving tool handling.

General safety instruc-

tions for power tools

WARNING! Read all

safety directions and

instructions. Omissions in

the compliance with safety

directions and instructions

can cause electrical shock,

re and/or severe injuries.

Retain all safety directions and

instructions for future use.

The term “Power Tools” used in the

safety instructions refers to mains-

operated power tools (with power

cord) and to battery-operated pow-

er tools (without power cord).

1) WORK AREA SAFETY

a) Keep work area clean

and well lit. Cluttered or dark

areas invite accidents.

b) Do not operate power

tools in explosive atmos-

pheres, such as in the

presenceofammable

Iiquids, gases or dust.

8

IE NIGB

Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystand-

ers away while operating

a power tool. Distractions

can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must

match the outlet. Never

modify the plug in any

way. Do not use any

adapter plugs with

earthed (grounded) power

tools. Unmodied plugs and

matching outlets will reduce risk

of electric shock.

b) Avoid body contact with

earthed or grounded sur-

faces, such as pipes, ra-

diators, ranges and refrig-

erators. There is an increased

risk of electric shock if your

body is earthed or grounded.

c) Do not expose power

tools to rain or wet condi-

tions. Water entering a power

tool will increase the risk of

electric shock.

d) Do not abuse the cord.

Never use the cord for

carrying, pulling or un-

plugging the power tool.

Keep cord away from

heat, oil, sharp edges or

moving parts. Damaged or

entangled cords increase the

risk of electric shock.

e) When operating a power

tool outdoors, use an ex-

tension cord suitable for

outdoor use. Use of a cord

suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool

in a damp location is una-

voidable, use a residual

current device (RCD) pro-

tected supply. Use of an RCD

reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you

are doing and use common

sense when operating a

power tool. Do not use a

power tool while you are

tiredorundertheinuence

of drugs, alcohol or medi-

cation. A moment of inattention

white operating power tools may

result in serious personal injury.

b) Use personal protective

equipment. Always wear

eye protection. Protective

equipment such as dust mask,

non-slip safety shoes, hard hat,

or hearing protection used for

appropriate conditions will re-

duce personal injuries.

c) Prevent unintentional

starting. Ensure the switch

is in the off-position be-

fore connecting to power

source and/or battery

pack, picking up or car-

rying the tool. Carrying

power tools with your nger on

the switch or energising power

tools that have the switch on

invites accidents.

d) Remove any adjusting key

or wrench before turning

the power tool on. A wrench

or a key left attached to a rotat-

ing part of the power tool may

result in personal injury.

9

IE NIGB

e) Do not overreach. Keep

proper footing and bal-

ance at all times. This ena-

bles better control of the power

tool in unexpected situations.

f) Dress properly. Do not

wear loose clothing or

jewellery. Keep your hair,

clothing and gloves away

from moving parts. Loose

clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided

for the connection of dust

extraction and collection

facilities, ensure these are

connected and properly

used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power

tool. Use the correct power

tool for your application.

The correct power tool will do

the job better and safer at the

rate for which it was designed.

b) Do not use the power tool

if the switch does not turn

it on and off. Any power tool

that cannot be controlled with

the switch is dangerous and

must be repaired.

c) Disconnect the plug from

the power source and/or

the battery pack from the

power tool before making

any adjust -ments, chang-

ing accessories, or storing

power tools. Such preventive

safety measures reduce the risk

of starting the power tool acci-

dentaIly.

d) Store idle power tools out

of the reach of children

and do not allow persons

unfamiliar with the power

tool or these instructions

to operate the power tool.

Power tools are dangerous in

the hands of untrained users.

e) Maintain power tools.

Check for misalignment

or binding of moving

parts, breakage of parts

and any other condi-

tion that may affect the

power tool’s operation.

If damaged, have the power

tool repaired before use. Many

accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp

and clean. Properly main-

tained cutting tools with sharp

cutting edges are less Iikely to

bind and are easier to control.

g) Use the power tool, acces-

sories and tool bits etc. in

accordance with these in-

structions, taking into ac-

count the working condi-

tions and the work to be

performed. Use of the power

tool for operations different

from those intended could result

in a hazardous situation.

h) Ensure that the vents are free of

soiling.

i) Remove the battery pack

from the power tool

- whenever the user no longer

remains in the vicinity of the

machine.

- before the removal of blockages.

- before checking, cleaning or

working on the machine.

10

IE NIGB

- after touching a foreign body in

order to check the machine for

damage.

- for an immediate check if the

machine begins to vibrate ex-

cessively.

5) SERVICE

Have your power tool ser-

vicedbyaqualiedrepair

person using only identi-

cal replacement parts. This

will ensure that the safety of the

power tool is maintained.

Additional safety instruc-

tions

TRAINING

• The appliance is not suitable

for use by children. Children

should be supervised to ensure

that they do not play with the

appliance. Cleaning and user

maintenance shall not be made

by children.

• This appliance is not intended

for use by persons with reduced

physical, sensory or mental ca-

pabilities, or lack of experience

and knowledge.

• Local regulations or bylaws

may determine the minimum

age for using the device.

• The operator or user is responsi-

ble for accidents or damage to

other persons or their property.

• Children and persons with limi-

ted physical, sensory or mental

capabilities or inadequate

experience and knowledge, or

persons who are not familiar

with the instructions, should

never be allowed to use the

machine! Local regulations may

specify an age limit for the user.

• Never let children or persons

who are not familiar with the

instructions mentioned use the

machine.

PREPARATION

• Before each use, carry out a visu-

al inspection on missing or wron-

gly mounted protective devices or

parts of the cutting device.

• Before commissioning and after

any impacts, check for signs of

wear and damages, and have

any necessary repairs performed.

OPERATION

• Wear safety goggles, stable

shoes and long trousers over

the entire period of use of the

machine.

• The use of the machine under

bad weather conditions, espe-

cially in case of lightning risk,

must be avoided.

• Warning! Do not touch any mo-

ving dangerous parts before the

battery has been removed and

the moving dangerous parts

have come to a complete stop.

• Caution, risk of injury from cuts

on hands and feet.

• Stop using the machine when

persons, above all children, and

house pets are in the vicinity.

• Use the machine only in daylight

or with good articial lighting.

• Always keep your hands and

feet away from the cutting

equipment, above all when you

switch the motor on.

• Never install metallic cutting

elements.

11

IE NIGB

• Never use the machine with

damaged or missing protective

equipment.

• Avoid an abnormal body po-

sture. Ensure secure footing at

all times to maintain balance

when working on slopes.

• Go slowly. Do not walk with the

device in your hand.

• Always wear sturdy shoes and

long trousers during operation

of the machine.

• In the case of an accident

or malfunction during

operation, the device must

be switched off immedia-

tely. Injuries must be pro-

perly treated or medical

assistance sought. Read

the „Trouble shooting“ section

to correct any malfunctions or

contact our Service Centre.

MAINTENANCE AND STORAGE

• Remove the removable battery

before carrying out mainte-

nance or cleaning work.

• Use only spare parts and acces-

sories supplied and recommen-

ded by the manufacturer.

• The machine must be checked

regularly and maintained. Have

the machine repaired in a licen-

sed workshop.

Residual risks

Even if properly operating and han-

dling this electric tool, some residual

risks will remain. Due to its construc-

tion and build, this electric tool may

present the following hazards:

a) Cuts

b) Ear damage if working without

ear protection.

c) Damage to your health caused

by swinging your hands and

arms when operating the appli-

ance for longer periods of time

or if the unit is not held or main-

tained properly.

Warning! During operation,

this electric tool generates an

electromagnetic eld which,

under certain circumstances,

may impair the functionality

of active or passive medical

implants. To reduce the risk of

serious or lethal injuries, we

recommend that persons with

medical implants consult their

doctor and the manufacturer

of their medical implant be-

fore operating the machine.

Warning! Observe the safety

information in the operating

instructions for your Parkside

X 20 V Team series rechar-

geable battery.

Assembling instructions

Remove the rechargeable bat-

tery from the device before

assembly. Insert the rechar-

geable battery only once the

device is completely assem-

bled. There is a risk of injury!

Mounting the protective cover:

1. Place the protective cover (12)

onto the motor head (10) and

fasten it using the two Phillips

screws (19).

12

IE NIGB

2 Place the distance roller (16)

onto the protective cover (12)

and fasten it using the two small

Phillips screws (20).

Mounting the trimming unit:

3. Slip the nylon blade (14) onto the

axle. There is only one mounting

position. Screw the nylon blade

(14) to the axle. Take note: The

screw is a left-handed thread and

should be turned anti-clockwise to

tighten and clockwise to loosen.

Please ensure that the screws (21)

are properly tightened.

Place the cutting insert (13) on the

pin (22) on the cutting disk (14) and

pull out the insert until it snaps in.

Repeat the process with the two

plastic blades (13).

Spare cutting inserts are kept in

the box (

4) on the auxiliary

handle (

5).

To put on the auxiliary

handle:

4. Unscrew and remove the pre-

assembled screw (24) of the ad-

ditional handle (5).

5. Pull the ends of the auxiliary han-

dle (5) to extend the handle and

slide it over the handle holder

(23). The storage box for your pla-

stic knife (4) must point upwards.

6. Screw down the screw (24) in the

auxiliary handle (5).

Operation

Caution: risk of injury! Do not

operate the appliance with-

out the protective cover. To

operate the appliance, wear

suitable clothing, eye and ear

protection.

Prior to every use, check that

the appliance is operative. Do

not block the On/Off switch or

the switch lock. They must reli-

ably turn off the motor when

you release the switch. Do not

operate the appliance if one of

the switches is damaged.

Please observe local regulations

concerning noise protection.

Turning on and off

Maintain a rm stand and hold the

appliance well with both hands and at

some distance away from your body.

Before turning on the appliance, check

that it will not touch any objects.

1. To turn on, use your thumb to

actuate the switch lock (3), then

press the On/Off switch (2). Re-

lease the switch lock.

2. To turn off, release the On/Off

switch (2). There is no continuous

operation mode.

After turning off the appli-

ance, the trimming assembly

will keep revolving for some

time. Allow the trimming as-

sembly to come to a stand-

still. Neither touch nor slow

down the moving cutting in-

sert. Risk of injury!

13

IE NIGB

To adjust the spacer bow

(owerguard):The spacer bow keeps

the trimming assembly away from plants

and trunks not to be cut.



Fold down the distance bracket (15). If

the distance bracket is not required, fold

it up into the park position..

Manner of operation

WARNING. Danger of injury!

• Do not cut moist or wet grass.

• Prior to starting the appliance,

check that the cutting disk does

not contact stones, gravel or other

foreign bodies.

• Switch on the trimmer before you

approach the grass that is to be cut.

• Do not overload the trimmer dur-

ing operation.

• Avoid contact with obstacles

(stones, walls, fences, etc.) as this

will rapidly wear out the lines.

• Avoid using the device in bad

weather, especially if there is a

danger of lightning!

Cutting grass

Cut the grass by

swaying the trimmer

sideways to the

right and left. Cut

slowly while the

trimmer is tilted for-

wards by approx.

30°.

Cut tall grass by a series of levels from top

to bottom.

Trimmer settings

To adjust the auxiliary handle:

The auxiliary handle can be set to various

positions. Adjust the handle such that the

cutting disk slightly tilts forward in your

working position.



Loosen the screw (24) in the handle

and move the auxiliary handle (5) to

your favourite position. Tighten the

screw in the handle. The latching steps

integrated into the holder prevent the

handle changing position unintention-

ally.

To adjust the height:

The telescopic shaft allows you to adjust

the appliance to your personal size.



Loosen the threaded bush (8). Adjust

the telescopic shaft (9) to the correct

length and tighten the threaded bush.

To adjust the cutting angle:

Changing the cutting angle lets you trim

grass at places that a difcult to reach,

e.g. under benches or wall offsets.



Tread on the pedal (11) on the motor

housing and tilt the telescopic shaft

(9). There are 7 preset tilt angles (see

“Work instructions”).

To adjust the handle rod:

The handle rod can be turned by 90° and

180° (see “Work instructions”).



Press the latch (7) to release the

lock and rotate the handle section

0° 90° 180°

(6) until it latches into

the desired position.

14

IE NIGB

Vertical cut / lawn edge

trimming

Be particularly careful and

attentive when operating the

cutter vertically. To avoid in-

juries, keep enough distance

to the trimming assembly.

Setup for vertical trimming:

Move the appliance to the right and

left in a slow swinging motion to

trim slopes and steep inclines.

• Handle rod: 180° (see

)

• Cutting angle: 0° (see

)

• Spacer bow in parking position

Setup for edge trimming:

To trim lawn edges, slowly move

the appliance along the lawn edg-

es.

• Handle rod: 90° (see

)

• Cutting angle: 90° (see

)

• Spacer bow in parking position

Cleaning and

maintenance

Warning! Risk of injury from

moving dangerous parts!

Contact our Service Centre about

repairs and servicing not described

in this manual. Only use OEM

parts. Risk of injury!

Turn off the appliance and, before

doing any servicing, remove the

battery.

The following cleaning and servicing

should be done regularly. This will ensure

a long and reliable service life.

Cleaning

Do not spray the appliance

with water and do not im-

merse it in water. Electric

shock hazard!

• Keep clean the ventilation slots, motor

housing and handles of the appliance.

Use a damp cloth or a brush. Do not

use cleaning agents or solvents. You

may otherwise irreparably damage the

appliance.

• After every trimming session, remove

grass and soil from the protective cover

and the trimming assembly.

• To thoroughly clean the trimming as-

sembly, remove the cutting insert

(

13) (see “Replacing the cutting

insert”) and use a sharp knife to clean

the pin (

22).

General maintenance

• Prior to every use, check the appliance

for obvious defects such as loose, worn

or damaged parts. Check that the

screws in the cutting disk are tight.

• Check covers and safety devices for

damages and correct installation. Re-

place as necessary.

Replacing the cutting insert

1. Slide the cutting insert (13) in-

ward and push it out of the pin

(23) on the cutting disk (12).

2. Place the new cutting insert (13)

on the pin (23) and pull out the

insert until it snaps in.

15

IE NIGB

Storage

• Store the trimmer in a dry place well out

of reach of children.

• Do not stand the trimmer on its protec-

tive cover. Suspend it by its upper han-

dle in such a manner that the protective

cover does not come into contact with

other objects. This is because the pro-

tective cover could become deformed,

thereby changing its dimensions and its

safety properties.

Replacement parts/Accessories

Spare parts and accessories can be obtained at

www.grizzly-service.eu

If you do not have internet access, please contact the Service Centre via telephone

(see “Service-Center” page 18). Please have the order number mentioned below ready.

Battery charger EU ..................................................................................80001313

Battery charger UK .................................................................................. 80001314

Batter y ................................................................................................... 80001166

Protective cover ...................................................................................... 91099394

Cutting inser ts (pack of 20) ......................................................................91099406

Cutting disc ...........................................................................................91099395

Disposal and protection

of the environment

Remove the battery from the device and take

the device, battery, accessories and packag-

ing for environmentally friendly recycling.

Machines do not belong with do-

mestic waste.

• Return the unit to a recycling centre. The

plastics and metals in the unit can be

sorted and appropriately recycled. Ask

our Service Centre for details.

• Defective units returned to us will be dis-

posed of for free.

• Throw the cut grass on the compost. Do

not throw it in the normal household

waste.

16

IE NIGB

Trouble shooting

In the event of an accident or malfunction, remove the battery from the device im-

mediately! Failure to comply may result in injuries from cuts.

Problem Possible cause Corrective action

Appliance

won‘t start

Battery (

17) discharged

Recharge battery (

17)

(Observe the separate operating instructions

for the rechargeable battery and charger)

Battery (

17) not in

Insert battery (

17)

(Observe the separate operating instruc-

tions for the rechargeable battery and

charger)

On/Off switch (

2) defective

Send in to Service Centre for repair

Motor defective

Intermittent

operation

Internal loose contact

Send in to Service Centre for repair

On/Off switch (

2) defective

Much

vibration

Loud noise

Cutting insert (

13) broken

Replace cutting insert (

13)

(see „Cleaning and maintenance“)

Trimming assembly dirty

Clean trimming assembly

(see „Cleaning and maintenance“)

Motor defective Send in to Service Centre for repair

Bad trim

Cutting insert (

13) broken

Replace cutting insert (

13)

(see „Cleaning and maintenance“)

Trimming assembly dirty

Clean trimming assembly

(see „Cleaning and maintenance“)

Battery (

17) not fully charged

Recharge battery (

17)

(Observe the separate operating instructions

for the rechargeable battery and charger)

17

IE NIGB

Guarantee

Dear Customer,

This equipment is provided with a 3-year

guarantee from the date of purchase.

In case of defects, you have statutory rights

against the seller of the product. These

statutory rights are not restricted by our

guarantee presented below.

Terms of Guarantee

The term of the guarantee begins on the

date of purchase. Please retain the original

receipt. This document is required as proof

of purchase.

If a material or manufacturing defect occurs

within three years of the date of purchase

of this product, we will repair or replace –

at our choice – the product for you free of

charge. This guarantee requires the defec-

tive equipment and proof of purchase to be

presented within the three-year period with

a brief written description of what consti-

tutes the defect and when it occurred.

If the defect is covered by our guarantee, you

will receive either the repaired product or a

new product. No new guarantee period be-

gins on repair or replacement of the product.

Guarantee Period and Statutory

Claims for Defects

The guarantee period is not extended by

the guarantee service. This also applies for

replaced or repaired parts. Any damages

and defects already present at the time of

purchase must be reported immediately af-

ter unpacking. Repairs arising after expiry

of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully pro-

duced in accordance with strict quality

guidelines and conscientiously checked

prior to delivery.

The guarantee applies for all material and

manufacturing defects. This guarantee

does not extend to cover product parts

that are subject to normal wear and may

therefore be considered as wearing parts

(e.g. cutting inserts) or to cover damage to

breakable parts (e.g. battery, charger, cut-

ting plate, protective housing, switches).

This guarantee shall be invalid if the prod-

uct has been damaged, used incorrectly or

not maintained. Precise adherence to all of

the instructions specied in the operating

manual is required for proper use of the

product. Intended uses and actions against

which the operating manual advises or

warns must be categorically avoided.

The product is designed only for private

and not commercial use. The guarantee

will be invalidated in case of misuse or

improper handling, use of force, or inter-

ventions not undertaken by our authorised

service branch.

Processing in Case of Guarantee

To ensure quick handling of you issue,

please follow the following directions:

• Please have the receipt and item num-

ber (IAN 311046) ready as proof of

purchase for all enquiries.

• Please nd the item number on the rat-

ing plate.

• Should functional errors or other de-

fects occur, please initially contact the

service department specied below by

telephone or by e-mail. You will then

receive further information on the pro-

cessing of your complaint.

• After consultation with our customer

service, a product recorded as defec-

tive can be sent postage paid to the

service address communicated to you,

with the proof of purchase (receipt)

and specication of what constitutes

the defect and when it occurred. In or-

18

IE NIGB

der to avoid acceptance problems and

additional costs, please be sure to use

only the address communicated to you.

Ensure that the consignment is not sent

carriage forward or by bulky goods,

express or other special freight. Please

send the equipment inc. all accessories

supplied at the time of purchase and

ensure adequate, safe transport pack-

aging.

Repair Service

For a charge, repairs not covered by the

guarantee can be carried out by our ser-

vice branch, which will be happy to issue

a cost estimate for you.

We can handle only equipment that has

been sent with adequate packaging and

postage.

Attention: Please send your equipment to

our service branch in clean condition and

with an indication of the defect.

Equipment sent carriage forward or by

bulky goods, express or other special

freight will not be accepted.

We will dispose of your defective devices

free of charge when you send them to us.

Service-Center

GB

Service Great Britain

Tel.: 0800 404 7657

(£ 0.10/Min.)

E-Mail: [email protected]

IAN 311046

IE

NI

Service Ireland

Northern Ireland

Tel.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (off peak))

E-Mail: [email protected]

IAN 311046

Importer

Please note that the following address

is not a service address. Please initially

contact the service centre specied above.

Grizzly Tools GmbH & Co. KG

Stockstädter Straße 20

63762 Großostheim

Germany

www.grizzly-service.eu

19

AT CHDE

Inhalt

Einleitung ...................................19

Bestimmungsgemäße

Verwendung .............................. 19

Allgemeine Beschreibung ...........20

Lieferumfang.................................. 20

Funktionsbeschreibung .................... 20

Übersicht ...................................... 20

Technische Daten ........................21

Sicherheitshinweise ....................21

Symbole und Bildzeichen ................ 21

Allgemeine Sicherheitshinweise für

Elektrowerkzeuge ........................... 22

Weiterführende Sicherheitshinweise . 25

Restrisiken ..................................... 27

Montageanleitung ......................27

Bedienung .................................28

Ein- und Ausschalten ....................... 28

Einstellungen am Gerät ................... 28

Einleitung

Herzlichen Glückwunsch zum Kauf Ihres

neuen Gerätes. Sie haben sich damit für

ein hochwertiges Gerät entschieden. Die-

ses Gerät wurde während der Produktion

auf Qualität geprüft und einer Endkontrolle

unterzogen. Die Funktionsfähigkeit Ihres

Gerätes ist somit sichergestellt.

Die Betriebsanleitung ist Bestandteil

dieses Gerätes. Sie enthält wichtige

Hinweise für Sicherheit, Gebrauch und Ent-

sorgung. Machen Sie sich vor der Benut-

zung des Gerätes mit allen Bedien- und Si-

cherheitshinweisen vertraut. Benutzen Sie

das Gerät nur wie beschrieben und für die

angegebenen Einsatzbereiche.

Bewahren Sie die Betriebsanleitung gut auf

und händigen Sie alle Unterlagen bei Wei-

tergabe des Gerätes an Dritte mit aus.

Original-EG-Konformitäts-

erklärung ..................................36

Explosionszeichnung .................. 37

Arbeitshinweise .........................29

Gras schneiden ............................. 29

Senkrechtschnitt/Rasenkantentrimmen 30

Reinigung und Wartung .............30

Reinigung ..................................... 30

Allgemeine Wartungsarbeiten ......... 30

Kunststoff-Messer auswechseln ......... 31

Lagerung ...................................31

Entsorgung/Umweltschutz ..........31

Garantie ....................................31

Reparatur-Service ......................32

Service-Center ............................33

Importeur .................................. 33

Ersatzteile/Zubehör ...................33

Fehlersuche ................................34

Bestimmungsgemäße

Verwendung

Das Gerät ist nur zum Schneiden von Gras

in Gärten und entlang von Beeträndern

geeignet. Jede andere Verwendung, die in

dieser Anleitung nicht ausdrücklich zuge-

lassen wird, kann zu Schäden am Gerät

führen und eine ernsthafte Gefahr für den

Benutzer darstellen. Verwenden Sie das Ge-

rät nicht zum Schneiden von Hecken oder

Sträuchern. Das Gerät ist zum Gebrauch

durch Erwachsene bestimmt. Jugendliche

über 16 Jahre dürfen das Gerät nur unter

Aufsicht benutzen. Der Hersteller haftet nicht

für Schäden, die durch bestimmungswid-

rigen Gebrauch oder falsche Bedienung

verursacht wurden. Dieses Gerät ist nicht

zur gewerblichen Nutzung geeignet. Bei

gewerblichem Einsatz erlischt die Garantie.

20

DE AT CH

Allgemeine Beschreibung

Die Abbildung der wichtigs-

ten Funktionsteile nden Sie

auf der vorderen und der

hinteren Ausklappseite.

Lieferumfang

Packen Sie das Gerät aus und kontrollieren

Sie, ob es vollständig ist:

- Akku-Rasentrimmer

- Schneidscheibe mit einer Schraube

(Linksgewinde)

- Schutzabdeckung mit zwei Schrauben

- Abstandsrolle mit zwei Schrauben

- Zusatzgriff

- 20 Kunststoff-Messer

- Ladegerät

- Akku

- Betriebsanleitung Ladegerät und Akku

- Betriebsanleitung

Funktionsbeschreibung

Der handgeführte und tragbare Akku-Ra-

sentrimmer besitzt als Schneideinrichtung

ein Messersystem aus Kunststoff.

Zusätzlich ist das Gerät mit einem schwenk-

baren Motorkopf, verstellbarem Alu-Teleskop-

rohr und Distanzbügel ausgestattet.

Zum Schutz des Anwenders ist das Gerät

mit einer Schutzeinrichtung versehen, die

die Schneideinrichtung abdeckt.

Die Funktion der Bedienteile entnehmen Sie

bitte den nachfolgenden Beschreibungen.

Übersicht

1 Oberer Handgriff

2 Ein-/Ausschalter

3 Einschaltsperre

4 Aufbewahrungsbox für Kunst-

stoff-Messer

5 Zusatzgriff

6 Griffteil

7 Riegel zur Verstellung

des Griffteils

8 Schraubhülse

zur Längenverstellung

9 Teleskoprohr

10 Motorkopf

11 Druckknopf zur Verstellung des

Neigungswinkels

12 Schutzabdeckung

13 Kunststoff-Messer

14 Schneidscheibe

15 Distanzbügel (Blumenschutz)

16 Abstandsrolle

17 Akku

18 Ladegerät

19 Schrauben Schutzabdeckung

20 Schrauben Abstandsrolle

21 Schraube Schneidscheibe

22 Stift, Schneidscheibe

23 Griffaufnahme

24 Griffschraube

Seite laden ...

Parkside PRTA 20-Li A1 Translation Of The Original Instructions

Parkside PRTA 20-Li A1 Translation Of The Original Instructions

in anderen Sprachen

Verwandte Papiere

Sonstige Unterlagen