LIVARNO 300635 Bedienungsanleitung

LED LIGHT

IAN 300635

LED-STRAHLER

Montage-, Bedienungs- und Sicherheitshinweise

LED LIGHT

Assembly, operating and safety instructions

LAMPA WARSZTATOWA LED

Wskazówki montażu, obsługi i bezpieczeństwa

GB Assembly, operating and safety instructions Page 5

PL Wskazówki montażu, obsługi i bezpieczeństwa Strona 18

DE / AT / CH Montage-, Bedienungs- und Sicherheitshinweise Seite 32

A

C

B

D

3

5 46

8 95

8

1

2

7

0m 2m 4m 6m 8m

2m

ca.140°

ca.8m

E

F

10

11

5 GB

List of pictograms used ............................................ Page 6

Introduction ....................................................................... Page 6

Intended use ............................................................................ Page 7

Parts description ...................................................................... Page 7

Technical data ......................................................................... Page 8

Scope of delivery .................................................................... Page 8

General safety instructions .................................. Page 9

Safety instructions for batteries / rechargeable batteries ..... Page 10

Function................................................................................. Page 11

Installation ......................................................................... Page 12

Replacing the batteries ........................................................... Page 13

Setting the lighting duration .................................................... Page 14

Setting the daylight level ........................................................ Page 14

Cleaning and care ........................................................ Page 15

Troubleshooting ............................................................ Page 15

Disposal ................................................................................ Page 15

Warranty ............................................................................. Page 17

6 GB

List of pictograms used

Motion detector detection range approx. 8 m

(weather dependant)

This product is suitable for extreme

temperature up to -21°C.

Motion detector detection angle approx. 140°

Splashproof (IP44)

LED lifespan

Direct current

LED Light

Introduction

We congratulate you on the purchase of your new product. You have

chosen a high quality product. The instructions for use are part of the

product. They contain important information concerning safety, use

and disposal. Before using the product, please familiarise yourself with

7 GB

all of the safety information and instructions for use. Only use the

product as described and for the speciﬁed applications. If you pass

the product on to anyone else, please ensure that you also pass on all

the documentation with it.

Intended use

The

product

is intended to illuminate outdoor areas without electrical

connection, e.g. garden sheds etc. This product is only intended for

private use and is not suitable for commercial use or for use in other

applications.

Not suitable for ordinary lighting in household room

illumination.

This product is suitable for extreme temperature up to -21°C.

Parts description

1 Main unit

2 LED spotlight

3 Motion detector

4 Screw (Ø 3.6 x 30 mm)

5 Mounting plate

6 Wall plug (Ø 6 mm)

7 Cap

8 Battery compartment cover

9 Battery compartment

10 Rotary control LUX

11 Rotary control TIME

8 GB

Technical data

Operating voltage: 4 x 1.5 V (direct current)

Operating batteries: 4 x 1.5 V (direct current), size C

LEDs: 2 x 4 W (LEDs not replaceable)

Motion detector: Range: max. 8 m, detection angle:

approx. 140° horizontal, approx. 90° vertical

Degree of protection: IP44 (splash-proof)

Weight: 370 g

Dimensions: approx. 19.4 x 14.5 x 10.5 cm

Projected area: max. 19.4 x 14.5 cm

Mounting height: max. 2 m

Scope of delivery

Check immediately after unpacking that the parts are complete and

that the product is in proper condition.

1 Main unit

4 Batteries (1.5 V, size C)

2 Screws (Ø 3.6 x 30 mm)

2 Wall plugs (Ø 6 mm)

2 Caps

1 Instructions for assembly and use

9 GB

General safety instructions

BEFORE USING THE PRODUCT, PLEASE FAMILIARISE YOURSELF

WITH ALL OF THE SAFETY INFORMATION AND INSTRUCTIONS

FOR USE! WHEN PASSING THIS PRODUCT ON TO OTHERS,

PLEASE ALSO INCLUDE ALL THE DOCUMENTS!

This product may be used by children age 8 years and up, as well

as by persons with reduced physical, sensory or mental capaci

ties,

or lacking experience and / or knowle

dge, so long as they are super-

vised or instructed in the safe use of the product and understand

the associated risks. Children should not be allowed to play with

the product. Cleaning and user maintenance should not be per-

formed by children without supervision.

Never leave children unsupervised with the packaging material.

The packaging material represents a danger of suﬀocation.

Children frequently underestimate the dangers.

DANGER OF SUFFOCATION! Children could swallow and

choke on small included parts (e.g. screws). Keep children away

from the work area during assembly.

Do not use this product if you notice any damage!

The LEDs are not replaceable.

If the LEDs fail at the end of their lives, the entire product must be

replaced.

0.1 m

FIRE HAZARD! Fit the product so that it is at least

0.1 m away from the material to be illuminated. Exces-

sive heat can result in a ﬁre.

10 GB

Risk Group 2

Product tested against EN62471

CAUTION. Possibly hazardous

optical radiation emitted from

this product. Do not stare at operating

lamp. May be harmful to the eye.

Safety instructions for batteries /

rechargeable batteries

DANGER TO LIFE! Keep batteries / rechargeable batteries out

of reach of children. If accidentally swallowed seek immediate

medical attention.

DANGER OF EXPLOSION! Never recharge non-

rechargeable batteries. Do not short-circuit batteries /

rechargeable batteries and / or open them. Overheating,

ﬁre or bursting can be the result.

Never throw batteries / rechargeable batteries into ﬁre or water.

Do not exert mechanical loads to batteries / rechargeable batteries.

Risk of leakage of batteries / rechargeable batteries

Avoid extreme environmental conditions and temperatures, which

could aﬀect batteries / rechargeable batteries, e.g. radiators /

direct sunlight.

If batteries / rechargeable batteries have leaked, avoid contact

with skin, eyes and mucous membranes with the chemicals! Flush

11 GB

immediately the aﬀected areas with fresh water and seek medical

attention!

WEAR PROTECTIVE GLOVES! Leaked or damaged

batteries / rechargeable batteries can cause burns on

contact with the skin. Wear suitable protective gloves at

all times if such an event occurs.

In the event of a leakage of batteries / rechargeable batteries, im-

mediately remove them from the product to prevent damage.

Only use the same type of batteries / rechargeable batteries. Do

not mix used and new batteries / rechargeable batteries.

Remove batteries / rechargeable batteries if the product will not be

used for a longer period.

Risk of damage of the product

Only use the speciﬁed type of battery / rechargeable battery!

Insert batteries / rechargeable batteries according to polarity

marks (+) and (-) on the battery / rechargeable battery and the

product.

Clean the contacts on the battery / rechargeable battery and in

the battery compartment before inserting!

Remove exhausted batteries / rechargeable batteries from the

product immediately.

Function

During periods of twilight or darkness, the motion detector 3 registers

a change in the angle of heat radiation, triggered by people passing

by the motion detector. When the motion detector recognises a moving

person the light is switched on.

12 GB

Note: The motion detector 3 responds to heat radiation. When out-

door temperatures are low, it is more sensitive to body heat than when

outdoor temperatures are warm. Be sure to regulate the sensitivity of

the motion detector over the course of the year.

Note: Regularly clean the motion detector to ensure proper function-

ality (refer to „Cleaning and Care“).

Installation

Note: Remove all packaging materials from the product.

When selecting the mounting location, pay attention to the

following:

Note: The included mounting material is suitable for ordinary

solid concrete or masonry construction. Other wall substrates may

require other fastening materials. Seek specialist advice if necessary.

Note: You will need an electric drill.

CAUTION! RISK OF INJURY! Please read the operating

instructions for your drill.

CAUTION! Ensure that you do not damage any electricity cables

in the wall or ceiling.

1. Make sure the LED spotlights 2 illuminate the desired area. You

can move the LED spotlights 2 independently in various directions.

2. Depending on the mounting height (ideally at 2 m) the motion

detector 3 has a detection range of max. 8 m with a detection

angle of 140° horizontally and 90° vertically.

3. Be sure the motion detector is not illuminated by street lighting at

night. This can inﬂuence the eﬀect.

13 GB

Loosen the screw on the bottom of the main unit 1 with a suitable

cross-head screwdriver. Remove the mounting plate 5 from the

back of the product (Fig. A).

Pay attention to the battery compartment cover 8.

Use the holes of the mounting plate 5 intended for the screws to

mark the holes for drilling. Ensure that the arrow on the marking

of the mounting plate is showing vertically upward.

Now drill the mounting holes.

Insert the wall plugs 6 into the drilled holes (Fig. B).

Fix the mounting plate 5 using the screws 4 with a suitable

cross-head screwdriver (Fig. B).

Press the caps 7 onto the screws 4.

After mounting, check that the mounting plate 5 is ﬁtted securely.

Remove the battery compartment cover 8 and insert the batteries,

then close the battery compartment cover 8 (refer to “Replacing

the batteries”)

Fit the main unit 1 onto the mounting plate 5. Insert the 2 lugs

into the respective slots on the upper side of the mounting plate 5.

Ensure the product is correctly seated.

Secure the main unit 1 with the screw on the bottom (Fig. A).

Adjust both LED spotlights 2 to your desired angle. The LED spot-

lights 2 are independently rotatable and tiltable.

Your product is now ready for use.

Replacing the batteries

Loosen the screw on the bottom of the main unit 1 with a suitable

cross-head screwdriver (Fig. A).

Detach the main unit 1 from the mounting plate 5 (Fig. C).

14 GB

Press the lugs on both sides and remove the battery compartment

cover 8 (Fig. D). Be careful as the battery compartment cover is

under tension.

Remove the exhausted batteries from the battery compartment 9

and replace with new batteries of the same type (Fig. E). Be sure

to insert the batteries in correct direction. The correct polarity is

shown inside the battery compartment.

Close the battery compartment cover 8. Ensure that the label

“above” on the marking of the battery compartment cover 8 is

showing vertically upward (Fig. D).

Fit the main unit 1 onto the mounting plate 5. Insert the 2 lugs

into the respective slots on the upper side of the mounting plate

5. Ensure the product is correctly seated.

Secure the main unit 1 with the screw on the bottom (Fig. A).

Setting the lighting duration

Turn the rotary control TIME 11 clockwise to increase the duration

of the illumination. The lighting duration can be adjusted within a

time window of approx. 5 seconds to 7 minutes (Fig. F).

Setting the daylight level

Turn the rotary control LUX 10 clockwise to increase the daylight

level: In the position, the motion detector 3 only reacts at night

(at approx. 20 lx). In the position, the motion detector also re-

sponds at daylight levels, as long as about 10,000 lx are not ex-

ceeded (Fig. F).

15 GB

Cleaning and care

Use a slightly dampened, lint-free cloth and mild cleaning agent to

clean.

Regularly check the motion detector 3 for dirt.

Regularly clean the motion detector to ensure proper functionality.

Troubleshooting

Problem Cause Solution

The light does

not switch on.

Motion detector 3 is dirty Clean motion

detector

Batteries are drained Change batteries

The light ﬂickers. Batteries are almost drained Change batteries

Disposal

The packaging is made entirely of recyclable materials, which you

may dispose of at local recycling facilities.

b

a

Observe the marking of the packaging materials for waste

separation, which are marked with abbreviations (a) and

numbers (b) with following meaning: 1–7: plastics / 20–22:

paper and ﬁbreboard / 80–98: composite materials.

16 GB

The product and packaging materials are recyclable,

dispose of it separately for better waste treatment. The

Triman logo is valid in France only.

Contact your local refuse disposal authority for more details

of how to dispose of your worn-out product.

To help protect the environment, please dispose of the prod-

uct properly when it has reached the end of its useful life

and not in the household waste. Information on collection

points and their opening hours can be obtained from your

local authority.

Faulty or used batteries / rechargeable batteries must be recycled in

accordance with Directive 2006/66/EC and its amendments. Please

return the batteries / rechargeable batteries and / or the product to the

available collection points.

Environmental damage through incorrect dis-

posal of the batteries / rechargeable batteries!

Batteries / rechargeable batteries may not be disposed of with the

usual domestic waste. They may contain toxic heavy metals and are

subject to hazardous waste treatment rules and regulations. The chemical

symbols for heavy metals are as follows: Cd = cadmium, Hg = mercury,

Pb = lead. That is why you should dispose of used batteries / recharge-

able batteries at a local collection point.

17 GB

Warranty

The product has been manufactured to strict quality guidelines and

meticulously examined before delivery. In the event of product defects

you have legal rights against the retailer of this product. Your legal

rights are not limited in any way by our warranty detailed below.

The warranty for this product is 3 years from the date of purchase.

Should this product show any fault in materials or manufacture within

3 years from the date of purchase, we will repair or replace it – at our

choice – free of charge to you.

The warranty period begins on the date of purchase. Please keep the

original sales receipt in a safe location. This document is required as

your proof of purchase. This warranty becomes void if the product has

been damaged, or used or maintained improperly.

The warranty applies to defects in material or manufacture. This war-

ranty does not cover product parts subject to normal wear, thus pos-

sibly considered consumables (e.g. batteries) or for damage to fragile

parts, e.g. switches, rechargeable batteries or glass parts.

18 PL

Legenda zastosowanych

piktogramów................................................................ Strona 19

Wstęp .................................................................................. Strona 19

Zastosowanie zgodne z przeznaczeniem ......................... Strona 20

Opis części ........................................................................... Strona 20

Dane techniczne .................................................................. Strona 21

Zawartość ............................................................................. Strona 21

Wskazówki ogólne dotyczące

bezpieczeństwa .......................................................... Strona 22

Wskazówki bezpieczeństwa dla baterii / akumulatorów.... Strona 23

Funkcja ............................................................................... Strona 25

Montaż ............................................................................... Strona 25

Wymiana baterii .................................................................. Strona 27

Ustawianie czasu świecenia ............................................... Strona 28

Ustawianie poziomu światła dziennego ............................ Strona 28

Czyszczenie i pielęgnacja ................................... Strona 28

Usuwanie usterek ..................................................... Strona 29

Utylizacja ......................................................................... Strona 29

Gwarancja ...................................................................... Strona 30

19 PL

Legenda zastosowanych piktogramów

Zasięg wykrywalności czujnika ruchu ok. 8 m

(w zależności od warunków atmosferycznych)

Produkt ten nadaje się do ekstremalnych temperatur

do -21°C.

Kąt wykrywania czujnika ruchu ok. 140°

Ochrona przed pryskającą wodą (IP44)

Żywotność diod LED

Prąd stały

Lampa warsztatowa LED

Wstęp

Gratulujemy Państwu zakupu nowego produktu. Tym samym zdecydo-

wali się Państwo na zakup produktu wysokiej jakości. Instrukcja

obsługi jest częścią tego produktu. Zawiera ona ważne wskazówki

dotyczące bezpieczeństwa, użytkowania iutylizacji. Przed pierwszym

20 PL

użyciem produktu należy zapoznać się ze wszystkimi wskazówkami

dotyczącymi obsługi ibezpieczeństwa. Używać produktu wyłącznie

zgodnie zjego poniżej opisanym przeznaczeniem. Wprzypadku

przekazania produktu innej osobie należy dołączyć do niego całą

jego dokumentację.

Zastosowanie zgodne z przeznaczeniem

Ten produkt przeznaczony jest do oświetlania obszaru na zewnątrz,

w miejscach nieposiadających własnego przyłącza elektrycznego,

np. altan ogrodowych, garaży itp. Produkt jest przeznaczony wyłącz-

nie do prywatnego użytku, a nie do zastosowania komercyjnego lub

innych zastosowań.

Ten produkt nie nadaje się jako oświetlenie pomiesz-

czeń domowych.

Produkt ten nadaje się do ekstremalnych temperatur do -21°C.

Opis części

1 Jednostka główna

2 Spot LED

3 Czujnik ruchu

4 Śruba (Ø 3,6 x 30 mm)

5 Płyta montażowa

6 Kołek (Ø 6 mm)

7 Zaślepka

8 Pokrywa komory baterii

9 Komora baterii

10 Pokrętło regulacyjne LUX

11 Pokrętło regulacyjne TIME

Seite laden ...

LIVARNO 300635 Bedienungsanleitung

LIVARNO 300635 Bedienungsanleitung

in anderen Sprachen

Verwandte Papiere