Nortel 4000 Benutzerhandbuch

Typ
Benutzerhandbuch

Dieses Handbuch ist auch geeignet für

Part No. 119500-A Rev. A
January 1998
Nautica 4000
Installation Guide
4401 Great America Parkway 8 Federal Street
Santa Clara, CA 95054 Billerica, MA 01821
ii 119500-A Rev. A
Copyright © 1998 Bay Networks, Inc.
All rights reserved. Printed in the UK. January 1998.
The information in this document is subject to change without notice. The statements,
configurations, technical data, and recommendations in this document are believed to be
accurate and reliable, but are presented without express or implied warranty. Users must
take full responsibility for their applications of any products specified in this document.
The information in this document is proprietary to Bay Networks, Inc.
Trademarks
Bay Networks is a registered trademark and BCC, Nautica and the Bay Networks logo are
trademarks of Bay Networks, Inc.
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft
Corporation.
All other trademarks and registered trademarks are the property of their respective owners.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, Bay
Networks, Inc. reserves the right to make changes to the products described in this
document without notice.
Bay Networks, Inc. does not assume any liability that may occur due to the use or
application of the product(s) or circuit layout(s) described herein.
119500-A Rev. A iii
USA Requirements Only
Federal Communications Commission (FCC) Compliance Notice: Radio Fre-
quency Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Battery Disposal
When disposing of the lithium battery module, this must be done in accordance with the
manufacturer’s disposal instructions.
European Requirements Only
EN 55 022 Statement
This is to certify that the Bay Networks Nautica 4000 is shielded against the generation of
radio interference in accordance with the application of Council Directive 89/336/EEC,
Article 4a. Conformity is declared by the application of EN 55 022 Class B (CISPR 22).
EC Declaration of Conformity
This product conforms (or these products conform) to the provisions of Council Directive
89/336/EEC and 73/23/EEC. The Declaration of Conformity is available on the Bay
Networks World Wide Web site at www.baynetworks.com.
iv 119500-A Rev. A
Power Supply
Power is provided via a standard IEC 320 (CEE-22) connector through an inlet on the rear
of the unit.
A single power cable, 2 metres in length, is supplied with the unit. This should be
connected to a suitable power supply. The power connector is the primary disconnect
device for the unit and you must ensure that the unit is installed near a power outlet and
that the outlet is accessible.
The power cable supplied with the unit is fitted with a moulded connector for connection to
the standard socket outlet. The use of adaptors is not recommended and may invalidate the
product’s approval. The wires in the power cable are coloured in accordance with the
following code:
Green and Yellow Earth
Blue Neutral
Brown Live
L’alimentation secteur est fournie par un connecteur standard IEC 320 (CEE-22) au travers
d’une prise située à l’arrière de l’unité.
A cable d’alimentation secteur de 2 mètres est fourni avec l’unité. Celui-ci devra être
connecté à une alimentation secteur. La prise secteur est le moyen primaire de
déconnection de l’unité et vous devez donc vous assurer qu’elle est installée près d’une
prise et que cette prise est accessible.
Le cordon secteur fourni avec l’unité possède un connecteur moulé pour la connection à
une prise de secteur standard. L’utilisation adapteurs n’est pas recommandée et peut
invalider l’homoligation du produit.
Les cables dans le cordon fourni sont colorisés selon les codes suivantes:
Vert et Jaune Terre
Bleu Neutre
Marron Phase
The “in-wall” power cable supplied with the Nautica 4000 must be used to ensure
continued compliance with the applicable regulations. Should a replacement power
module be required, this must be obtained from Bay Networks Inc.
Battery Disposal
When disposing of the lithium battery module, this must be done in accordance with the
manufacturer’s disposal instructions.
119500-A Rev. A v
Port Specifications
The Nautica 4000 has ports, which are classified as follows:
Interconnection circuits should be such that the equipment continues to comply with the
requirement of section 6.2 for Telecommunications Network Voltage (TNV) circuits and
section 2.3 for Safety Extra Low Voltage (SELV) circuits of EN 60950:1992/A4:1997 after
making connections between circuits.
Port Type Location
LAN 10BASE-T SELV Chassis
LAN AUI SELV Chassis
Manager SELV Chassis
BRI TNV Chassis
PRI TNV Chassis
WAN TNV (within the
limits of SELV)
Chassis
ISDN (J2) TNV BRI-ST Module
Host (J1) SELV BRI-ST Module
vi 119500-A Rev. A
Swedish Requirements Only
Denna produkt och expansionkort är avsedda för fackmannamässig installation i Sverige.
När service utförs på utrustningen, var vänlig koppla ur nätverket (inklusive ISDN-nätet)
först, innan kontakten dras ur.
Japan/Nippon Requirements Only
Voluntary Control Council for Interference (VCCI) Statement
Voluntary Control Council for Interference (VCCI) Statement
This is a Class B product based on the standard of the Voluntary Control Council for
Interference from Information Technology Equipment (VCCI). If this is used near a radio
or television receiver in a domestic environment, it may cause radio interference. Install
and use the equipment according to the instruction manual.
119500-A Rev. A vii
Canada Requirements Only
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (Nautica 4000) does not exceed the Class B limits for radio-noise
emissions from digital apparatus as set out in the Radio Interference Regulations of the
Canadian Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (Nautica 4000) respecte les limites de bruits radioélectriques
visant les appareils numériques de classe B prescrites dans le Règlement sur le brouillage
radioélectrique du ministère des Communications du Canada.
Canada CS-03 Rules and Regulations
Notice: The Industry Canada label identifies certified equipment. This certification means
that the equipment meets telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment Technical Requirements
document(s). The Department does not guarantee the equipment will operate to the user’s
satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected
to the facilities of the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. The customer should be aware that
compliance with the above conditions may not prevent the degradation of service in some
situations.
Repairs to certified equipment should be coordinated by a representative designated by the
supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to
disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the
power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.
Notice: For equipment using loopstart lines, please note that the Ringer Equivalence
Number (REN) assigned to each terminal device provides an indication of the maximum
number of terminals allowed to be connected to a telephone interface. The termination on
an interface may consist of any combination of devices subject only to the requirement that
the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. The REN
is located on the “FCC Rules Part 68” label located on the bracket of the module, or on the
back of the unit.
Canada CS-03 -- Règles et règlements
Av i s : L'étiquette d'Industrie Canada identifie le matériel homologué. Cette étiquette
certifie que le matériel est conforme aux normes de protection, d'exploitation et de sécuri
des réseaux de télécommunications, comme le prescrivent les documents concernant les
viii 119500-A Rev. A
exigences techniques relatives au matériel terminal. Le Ministère n'assure toutefois pas que
le matériel fonctionnera à la satisfaction de l'utilisateur.
Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux
installations de l'entreprise locale de télécommunication. Le matériel doit également être
installé en suivant une méthode acceptée de raccordement. L'abonné ne doit pas oublier
qu'il est possible que la conformité aux conditions énoncées ci-dessus n'empêche pas la
dégradation du service dans certaines situations.
Les réparations de matériel homologué doivent être coordonnées par un représentant
désigné par le fournisseur. L'entreprise de télécommunications peut demander à
l'utilisateur de débrancher un appareil à la suite de réparations ou de modifications
effectuées par l'utilisateur ou à cause de mauvais fonctionnement.
Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise à la terre de la
source d'énergie électrique, des lignes téléphoniques et des canalisations d'eau métalliques,
s'il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans
les régions rurales.
Avertissement: L'utilisateur ne doit pas tenter de faire ces raccordements lui-même; il
doit avoir recours à un service d'inspection des installations électriques, ou à un électricien,
selon le cas.
Av i s : Veuillez prendre note que pour tout appareillage supportant des lignes de type
“loopstart,” l'indice d'équivalence de la sonnerie (IES) assigné à chaque dispositif terminal
indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La
terminaison d'une interface téléphonique peut consister en une combinaison de quelques
dispositifs, à la seule condition que la somme d'indices d'équivalence de la sonnerie de tous
les dispositifs n'excède pas 5. Le REN figure sur l’étiquette “FCC Rules Part 68” située sur
le support du module ou à l’arrière de l’unité.
FCC Part 68 Compliance Statement
This equipment complies with Part 68 of FCC Rules. All direct connections to telephone
network lines must be made using standard plugs and jacks compliant with FCC Part 68.
Please note the following:
1. You are required to request service from the telephone company before you connect
the unit to a network. When you request service, you must provide the telephone
company with the following data:
When you request T1 Service, you must provide the telephone company with
-- The Facility Interface Code
Provide the telephone company with all the codes below:
- 04DU9-BN (1.544 MB, D4 framing format)
- 04DU9-DN (1.544 MB, D4 framing format with B8ZF coding)
- 04DU9-1KN (1.544 MB, ESF framing format)
- 04DU9-1SN (1.544 MB, ESF framing format with B8ZF coding)
- 04DU9-1ZN (1.544 MB, ANSI ESF and ZBTSI without line power)
The telephone company will select the code it has available.
-- The Service Order Code(s) (SOC): 6.0Y
119500-A Rev. A ix
-- The required Universal Service Order Code (USOC) jack: RJ48C
When you request ISDN “U” Interface Service, you must provide the telephone
company with
-- The Facility Interface Code: 02IS5
-- The Service Order Code(s) (SOC): 6.0F
-- The required Universal Service Order Code (USOC) jack: RJ49C
When you request ISDN “S/T” Interface Service, you must provide the
telephone company with
-- The Service Order Code(s) (SOC): 6.0P
-- The make, model number, and FCC Registration number of the NT1
Note: ISDN S/T cannot be directly connected to the network.
When you request Primary Rate ISDN Service, you must provide the telephone
company with
-- The Facility Interface Code: 04DU9-1SN (1.544 MB, ESF framing format
with B8ZF coding)
-- The Service Order Code(s) (SOC): 6.0Y
-- The required Universal Service Order Code (USOC) jack: RJ48C
2. Your telephone company may make changes to its facilities, equipment, operations, or
procedures that could affect the proper functioning of your equipment. The telephone
company will notify you in advance of such changes to give you an opportunity to
maintain uninterrupted telephone service.
3. If the unit causes harm to the telephone network, the telephone company may
temporarily discontinue your service. If possible, they will notify you in advance, but
if advance notice is not practical, you will be notified as soon as possible and will be
informed of your right to file a complaint with the FCC.
4. If you experience trouble with the unit, please contact the Bay Networks Technical
Solutions Center in your area for service or repairs. Repairs should be performed only
by service personnel authorized by Bay Networks, Inc.
United States 1-800-2LAN-WAN
Valbonne, France 33-4-92-96-69-68
Sydney, Australia 61-2-9927-8800
Tokyo, Japan 81-3-5402-0180
5. You are required to notify the telephone company when you disconnect the unit from
the network.
x 119500-A Rev. A
Module Installation Warning
The power required by the host and the total of adaptor cards installed within the host
environment, together with any auxiliary apparatus, shall not exceed the power
specifications of the host apparatus.
It is essential that when other option cards are introduced which use or generate a
hazardous voltage, the minimum creepages and clearances specified in Table 1
are
maintained. Suitable user protection to ensure compliance with EN 60950 should be
present on the card. A hazardous voltage is one which exceeds 42.4 V peak AC or 60 V
DC. If you have any doubt, seek advice from a competent engineer before installing other
adaptors into the host equipment.
The equipment must be installed such that, with the exception of the connections to the
host, clearance and creepage distances shown in Table 1
are maintained between the card
and any other assemblies which use or generate a voltage shown in the table below. The
larger distance shown in parentheses applies where the local environment within the host is
subject to conductive pollution or dry non-conductive pollution which could become
conductive due to condesation. Failure to maintain these minimum distances would
invalidate the approval.
Table 1. Creepage and Clearances
Clearance (mm) Creepage (mm)
Voltage used or
generated by Host or
other cards.
2.0 2.4 (3.8) Up to 50 V rms or V dc
2.6 3.0 (4.8) Up to 125 V rms or V dc
4.0 5.0 (8.0) Up to 250 V rms or V dc
4.0 6.4 (10.0) Up to 300 V rms or V dc
For a host or other expansion card
fitted in the host, using or generating
voltages greater than 300 V (rms or
dc), advice from a competent
telecommunications safety
engineer must be obtained before
the installation of the relevant
equipment.
Above 300 V rms or V dc
119500-A Rev. A xi
Figure 2. shows a physical representation of the creepage and clearances.
Figure 2. Creepage and Clearance
Except at the edge connectors, which plug into the host’s expansion slot, clearance
distance X (mm) and creepage distance Y (mm) as given in Table 1, must be maintained
between the communications card and any other assemblies that use or generate a
hazardous voltage.
ISDN Cards
The ISDN cable(s) must remain disconnected from the telecommunications system until
the card has been installed within a host that provides the necessary protection of the
operator.
If it is subsequently desired to open the host equipment for any reason, the ISDN cable(s)
must be disconnected prior to effecting access to the ISDN communications card.
xii 119500-A Rev. A
German Requirements Only
Stromversorgung
Der Strom wird über einen sereinmäßigen IEC 320 (CEE-22) Stecker durch eine
Einlaßöffnung an der Rückseite des Gerätes zugeführt.
Ein einzelnes Stromkabel von 2m Länge wird mit dem Gerät geliefert. Dieses sollte an
eine geeignete Stromversorgung angeschlossen werden. Der Stromstecker ist die
Haupt-Ausschaltvorrichtung des Geräts, und Sie müssen sicherstellen, daß das Gerät in der
Nähe einer Netxsteckdose montiert ist und daß diese erreichbar ist.
Das mit dem Gerät gelieferte Stromkabel ist mit einem geformten Stecker zum Anshluß an
eine Standard-Steckdose ausgestattet. Die Verwendung von Adapteren wird nicht
empfohlen und kann zur Außerkraftsetzung der Genehmigung des Gerätes führen. Die
Drähte im Stromkabel haben unterschiedliche Farben in Übereinstimmung mit dem
folgenden code:
Grün und Gelb Erdung
Blau Neutral
Braun Stromführend
Entsorgung der Batterie
Die Entsorgung des Lithium-Batterie-Moduls muß unter Einhaltung der
Entsorgungvorschriften des Herstellers erfolgen.
Portspezificationen
Das Nautica 4000 Gerät hat wie folgt klassifizierte ports:
Port Typ Standort
LAN 10BASE-T SELV Chassis
LAN AUI SELV Chassis
Manager SELV Chassis
BRI TNV Chassis
PRI TNV Chassis
WAN TNV (innerhalb
der Grenzen von
SELV)
Chassis
ISDN (J2) TNV BRIST-Modul
Host (J1) SELV BRIST-Modul
119500-A Rev. A xiii
Die Verbindungsschaltungen sollten so beschaffen sein, daß sie weiterhin den
Erfordernissen von Abschnitt 6.2 für Telecommunications Network Voltage (TNV)
Schaltungen und Abschnitt 2.3 für Safety Extra Low Voltage (SELV) Schaltungen der
bestimmungen EN60950:1992/A4:1997 entsprechen, nachdem die Verbindung zwischen
den Schaltungen hergestellt wurde.
Warnung für die Installation des Moduls
Der Strom, welcher vom Host und allen in der Hostumgebung installierten Adapterkarten
benötigt wird, darf nicht die Stromspezificationen für das Hostgeät überschrieten (siehe
S.3).
Es ist wichtig, daß auch bei Einführung anderer optionskarten, die eine gefährliche
spannung benutzen oder erzeugen, der in tabelle 1 angegebene mindestkriechstrom und die
mindestspielräume aufrechterhalten werden. Ein geeigenter benutzerschutz in
Übererinstimmung mit EN 60950 sollte auf der karte vorhanden sein. Eine gefährliche
spannung ist bei 42,4V spitzenleistung AC oder 60V DC gegeben. Wenn Sie im zweifel
sind, lassen Sie sich vor der installation anderer adapter in das Hostgerät von einem
erfahrenen Techniker beraten.
Das gerät muß so installiert sein, daß die in Tabelle 1 aufgeführten spielraum und
kriechstromentfernungen zwischen den karten und anderen baugruppen, die eine in der
untestehenden Tabelle angegebene spannung benutzen oder erzeugen, aufrechterhalten
bleiben. Die in klammern angegebene größere entfernung gilt, wo die örtliche umgebung
im Host leitfähiger verschmutzung bzw. trockener nichtleiender verschmutzung ausgesetzt
ist, welcher aufgrund von kondensation leitfähig werden kann. Das nichteinhalten dieser
Mindestentfernungen kann zur Außerkraftsetzung der genehmigung des gerätes führen.
Abbildung 2 seigt die physikalische darstellung von kriechstrom und spielräumen.
Kriechstrom Spielräume
Vom Host oder anderen karten
benutzte oder erzeugte Spannung
2.0 2.4 (3.8) Bis zu 50 V Effektivstrom oder V DC
2.6 3.0 (4.8) Bis zu 125 V Effektivstrom oder V DC
4.0 5.0 (8.0) Bis zu 250 V Effektivstrom oder V DC
4.0 6.4 (10.0) Bis zu 300 V Effektivstrom oder V DC
Bei einbau eines hosts oder einer anderen
erweiterungskarte, die größere
spannungen als 300 V (Effektivstrom oder
DC) benutzen oder erzeugen, muß vorher
Rat von einem kompetenten
Telekommunikations-Sicherheitstechniker
eingolt werden.
Über 300 V Effektivstrom oder DC
xiv 119500-A Rev. A
Abbildung 4. Kriechstrom und Spielräume
Ausgenommen an den randstiftleisen, die in den erweiterungsschlitz des hosts gesteckt
werden, muß spielraumentfernung X (mm) und Kriechstromentfernung Y (mm) gemäß
Tabelle 1 zwischen den kommunikationskarten und allen anderen baugruppen, die
gefährliche spannung benutzen oder erzeugen, aufrechthalten werden.
ISDN-Karten
Das ISDN-Kabel darf nicht an das telekommunikationssystem angeschlossen werden,
bevor die karte in einem host installiert wurde, der den notwendigen schutz für den
benutzer bietet.
Sollte das hostgerät zu einem späteren zeitpunkt aus irgendeinem grund geöffnet werden
müssen, muß das ISDN-Kabel entfernt werden, bevor zugang zur
ISDN-Kommunikationskarte möglich ist.
119500-A Rev. A xv
Bay Networks, Inc. Software License Agreement
NOTICE: Please carefully read this license agreement before copying or using the
accompanying software or installing the hardware unit with pre-enabled software (each of
which is referred to as “Software” in this Agreement). BY COPYING OR USING THE
SOFTWARE, YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS
LICENSE AGREEMENT. THE TERMS EXPRESSED IN THIS AGREEMENT ARE
THE ONLY TERMS UNDER WHICH BAY NETWORKS WILL PERMIT YOU TO
USE THE SOFTWARE. If you do not accept these terms and conditions, return the
product, unused and in the original shipping container, within 30 days of purchase to
obtain a credit for the full purchase price
1. License Grant. Bay Networks, Inc. (“Bay Networks”) grants the end user of the
Software (“Licensee”) a personal, nonexclusive, nontransferable license: a) to use the
Software either on a single computer or, if applicable, on a single authorized device
identified by host ID, for which it was originally acquired; b) to copy the Software solely
for backup purposes in support of authorized use of the Software; and c) to use and copy
the associated user manual solely in support of authorized use of the Software by Licensee.
This license applies to the Software only and does not extend to Bay Networks Agent
software or other Bay Networks software products. Bay Networks Agent software or other
Bay Networks software products are licensed for use under the terms of the applicable Bay
Networks, Inc. Software License Agreement that accompanies such software and upon
payment by the end user of the applicable license fees for such software.
2. Restrictions on use; reservation of rights. The Software and user manuals are
protected under copyright laws. Bay Networks and/or its licensors retain all title and
ownership in both the Software and user manuals, including any revisions made by Bay
Networks or its licensors. The copyright notice must be reproduced and included with any
copy of any portion of the Software or user manuals. Licensee may not modify, translate,
decompile, disassemble, use for any competitive analysis, reverse engineer, distribute, or
create derivative works from the Software or user manuals or any copy, in whole or in part.
Except as expressly provided in this Agreement, Licensee may not copy or transfer the
Software or user manuals, in whole or in part. The Software and user manuals embody Bay
Networks’ and its licensors’ confidential and proprietary intellectual property. Licensee
shall not sublicense, assign, or otherwise disclose to any third party the Software, or any
information about the operation, design, performance, or implementation of the Software
and user manuals that is confidential to Bay Networks and its licensors; however, Licensee
may grant permission to its consultants, subcontractors, and agents to use the Software at
Licensee’s facility, provided they have agreed to use the Software only in accordance with
the terms of this license.
3. Limited warranty. Bay Networks warrants each item of Software, as delivered by Bay
Networks and properly installed and operated on Bay Networks hardware or other
equipment it is originally licensed for, to function substantially as described in its
accompanying user manual during its warranty period, which begins on the date Software
is first shipped to Licensee. If any item of Software fails to so function during its warranty
period, as the sole remedy Bay Networks will at its discretion provide a suitable fix, patch,
or workaround for the problem that may be included in a future Software release. Bay
Networks further warrants to Licensee that the media on which the Software is provided
will be free from defects in materials and workmanship under normal use for a period of 90
xvi 119500-A Rev. A
days from the date Software is first shipped to Licensee. Bay Networks will replace
defective media at no charge if it is returned to Bay Networks during the warranty period
along with proof of the date of shipment. This warranty does not apply if the media has
been damaged as a result of accident, misuse, or abuse. The Licensee assumes all
responsibility for selection of the Software to achieve Licensee’s intended results and for
the installation, use, and results obtained from the Software. Bay Networks does not
warrant a) that the functions contained in the software will meet the Licensee’s
requirements, b) that the Software will operate in the hardware or software combinations
that the Licensee may select, c) that the operation of the Software will be uninterrupted or
error free, or d) that all defects in the operation of the Software will be corrected. Bay
Networks is not obligated to remedy any Software defect that cannot be reproduced with
the latest Software release. These warranties do not apply to the Software if it has been (i)
altered, except by Bay Networks or in accordance with its instructions; (ii) used in
conjunction with another vendor’s product, resulting in the defect; or (iii) damaged by
improper environment, abuse, misuse, accident, or negligence. THE FOREGOING
WARRANTIES AND LIMITATIONS ARE EXCLUSIVE REMEDIES AND ARE IN
LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. Licensee is responsible for the security of its own data
and information and for maintaining adequate procedures apart from the Software to
reconstruct lost or altered files, data, or programs.
4. Limitation of liability. IN NO EVENT WILL BAY NETWORKS OR ITS
LICENSORS BE LIABLE FOR ANY COST OF SUBSTITUTE PROCUREMENT;
SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES; OR ANY
DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE
OR PROFITS ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE
OF THE SOFTWARE, EVEN IF BAY NETWORKS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF
BAY NETWORKS RELATING TO THE SOFTWARE OR THIS AGREEMENT
EXCEED THE PRICE PAID TO BAY NETWORKS FOR THE SOFTWARE LICENSE.
5. Government Licensees. This provision applies to all Software and documentation
acquired directly or indirectly by or on behalf of the United States Government. The
Software and documentation are commercial products, licensed on the open market at
market prices, and were developed entirely at private expense and without the use of any
U.S. Government funds. The license to the U.S. Government is granted only with restricted
rights, and use, duplication, or disclosure by the U.S. Government is subject to the
restrictions set forth in subparagraph (c)(1) of the Commercial Computer
Software––Restricted Rights clause of FAR 52.227-19 and the limitations set out in this
license for civilian agencies, and subparagraph (c)(1)(ii) of the Rights in Technical Data
and Computer Software clause of DFARS 252.227-7013, for agencies of the Department
of Defense or their successors, whichever is applicable.
119500-A Rev. A xvii
6. Use of Software in the European Community. This provision applies to all Software
acquired for use within the European Community. If Licensee uses the Software within a
country in the European Community, the Software Directive enacted by the Council of
European Communities Directive dated 14 May, 1991, will apply to the examination of the
Software to facilitate interoperability. Licensee agrees to notify Bay Networks of any such
intended examination of the Software and may procure support and assistance from Bay
Networks.
7. Term and termination. This license is effective until terminated; however, all of the
restrictions with respect to Bay Networks’ copyright in the Software and user manuals will
cease being effective at the date of expiration of the Bay Networks copyright; those
restrictions relating to use and disclosure of Bay Networks’ confidential information shall
continue in effect. Licensee may terminate this license at any time. The license will
automatically terminate if Licensee fails to comply with any of the terms and conditions of
the license. Upon termination for any reason, Licensee will immediately destroy or return
to Bay Networks the Software, user manuals, and all copies. Bay Networks is not liable to
Licensee for damages in any form solely by reason of the termination of this license.
8. Export and Re-export. Licensee agrees not to export, directly or indirectly, the
Software or related technical data or information without first obtaining any required
export licenses or other governmental approvals. Without limiting the foregoing, Licensee,
on behalf of itself and its subsidiaries and affiliates, agrees that it will not, without first
obtaining all export licenses and approvals required by the U.S. Government: (i) export,
re-export, transfer, or divert any such Software or technical data, or any direct product
thereof, to any country to which such exports or re-exports are restricted or embargoed
under United States export control laws and regulations, or to any national or resident of
such restricted or embargoed countries; or (ii) provide the Software or related technical
data or information to any military end user or for any military end use, including the
design, development, or production of any chemical, nuclear, or biological weapons.
9. General. If any provision of this Agreement is held to be invalid or unenforceable by a
court of competent jurisdiction, the remainder of the provisions of this Agreement shall
remain in full force and effect. This Agreement will be governed by the laws of the state of
California.
Should you have any questions concerning this Agreement, contact Bay Networks, Inc.,
4401 Great America Parkway, P.O. Box 58185, Santa Clara, California 95054-8185.
LICENSEE ACKNOWLEDGES THAT LICENSEE HAS READ THIS AGREEMENT,
UNDERSTANDS IT, AND AGREES TO BE BOUND BY ITS TERMS AND
CONDITIONS. LICENSEE FURTHER AGREES THAT THIS AGREEMENT IS THE
ENTIRE AND EXCLUSIVE AGREEMENT BETWEEN BAY NETWORKS AND
LICENSEE, WHICH SUPERSEDES ALL PRIOR ORAL AND WRITTEN
AGREEMENTS AND COMMUNICATIONS BETWEEN THE PARTIES PERTAINING
TO THE SUBJECT MATTER OF THIS AGREEMENT. NO DIFFERENT OR
ADDITIONAL TERMS WILL BE ENFORCEABLE AGAINST BAY NETWORKS
UNLESS BAY NETWORKS GIVES ITS EXPRESS WRITTEN CONSENT,
INCLUDING AN EXPRESS WAIVER OF THE TERMS OF THIS AGREEMENT.
119500-A Rev. A xix
Contents
Nautica 4000 Installation Guide
Checklist ...............................................................................................2
Site Preparation .................................................................................... 3
ISDN Ordering Information ...................................................................4
European ISDN Information ........................................................... 4
North American ISDN Information .................................................4
WAN Ordering Information ....................................................................5
European WAN Information ...........................................................5
North American WAN Information ..................................................5
Connecting the Cables .........................................................................6
Nautica 4000 Front Panel Display .........................................................8
Requirements for the PC Applications ..................................................9
Installing the PC Applications ............................................................. 10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Nortel 4000 Benutzerhandbuch

Typ
Benutzerhandbuch
Dieses Handbuch ist auch geeignet für

in anderen Sprachen