NXS NX1000.1 Installation Instructions & Owner's Manual

Kategorie
Auto-Audio-Verstärker
Typ
Installation Instructions & Owner's Manual
POWER AMPLIFIERS
w/ DIGITAL SIGNAL PROCESSORS
Installation Instructions / Owner's Manual
NX200.2 NX400.2 NX400.4 NX900.5
NX500.1 NX1000.1 NX2000.1
INTRODUCTION
Congratulations on your purchase of a NXS state-of-the-art power amplifier with digital
signal processing. At NXS Mobile Audio we strive to provide some of the latest
technology tools that make the quest for “the perfect tune” so much easier. Our goal was
to develop technologically advanced amplifiers completely adjustable to the acoustics
of each vehicle.
RECOMMENDATION
A power amplifiers performance is only as good as its installation. Proper installation
will maximize the system’s overall performance. It is recommended that you have our
product installed by an authorized NXS retailer. However, if you decide to install it
yourself, please carefully read through this manual and take your time to do a quality
installation.
Due to continuing product improvements and possible manual revisions, we
recommend checking our website for latest product information at
www.nxsmobileaudio.com.
WARNING!
Exposure to high power sound system can cause hearing loss or damage. Listening to
your system at loud levels while driving, will impair your ability to hear traffic sounds and
emergency vehicles. Use common sense when listening to your system.
WARNING!
Exposure to high power sound system can cause hearing loss or damage. Listening to
your system at loud levels while driving, will impair your ability to hear traffic sounds and
emergency vehicles. Use common sense when listening to your system.
IMPORTANT! Before making any connections, disconnect the car’s battery until the installation
is completed to avoid possible damage to the electrical system.
Serial # Model #
1
ENGLISH
TAKE CONTROL
The NXS amplifiers feature built-in digital signal processors (DSP). The DSP allows for
control and adjustment of sophisticated features previously found only in mid-to high
end dedicated pre-amplifier equipment. The DSP features are controlled and adjusted
with one of the two following components (sold separately).
NXLI computer interface and NXCS software:
The NXLI is an control interface which allows
the amplifier's DSP to be controlled by a PC.
The NXLI provides a standard USB plug to
connect to a PC and a RJ11 socket for a cable
connection to the Amplifier's DSP Netlink.
The NXLI is powered by the USB connection
eliminating the need for additional power
connections. This makes the NXLI portable
and simple to connect.
Unlike traditional amplifier installations with the adjustments made on the amplifier in the
back of the car, the NXLI gives the flexibility to position a Laptop PC within the vehicle
while sitting in the listening position making the adjustments real-time. This allows for
ideal calibration of the system including equalization and time delay.
NXLCDC In-Dash Controller: The NXLCDC is an optional in-dash controller
for users who do not want to use a PC to setup
and control their NXS Amplifiers. Shaped in a
convenient DIN size, the NXLCDC features a
4 line LCD Display, a function selecting scroll
wheel, 4 preset buttons and a 'back' button.
This enables the user to select and adjust different amplifiers connected via DSP Netlink
in the same car. Basic settings like EQ, Gain, Sub-woofer level and Crossover can be
selected and adjusted.
The 4 presets on the NXLCDC can be programmed to recall up to 4 individual
configurations saved to the NXLCDC. The user can easily toggle configurations biased
toward 'classical' vs 'techno' music for instance.
There is also a Mini-USB PC computer input connection at the front of the controller.
This is to allow PCs with the NXCS software installed the convenience of connecting
and controlling the amps through the NXLCDC instead of having to run additional
cables.
NXLC Remote Level Control: The NXLC is a remote level control that gives hands-
on-control over the amplifier(s) output level. The
NXLC operates through the amplifiers DSP Netlink
connection and features an intelligent circuit
allowing you to select which amplifier and/or
channels you would like to control remotely.
Additionally, only one remote is needed to control
ENGLISH
2
SAFETY PRECAUTIONS
Fuse amplifier’s power wire at the battery.
Be sure to fuse the power wire within 6” of the car's battery. This will protect the car's
battery in case of a short circuit between the power amplifier and battery. THIS IS A
MUST, the amplifier's built-in fuse will only protect the power amplifier not the car's
battery!
Use high grade wire connectors.
To ensure maximum power transfer and secure safe connections, it is recommended to
use high grade barrier spades (for connection at amplifier) and terminal rings (for
connection at battery).
Do not run any wires underneath vehicle.
Exposed wires have a chance of being cut or damaged. It is best to run all wires through
the vehicle under the carpet and/or side panels. This lends to a cleaner installation and
less risk of damage.
Use caution when mounting amplifier.
Remember there are many electrical wires, gas lines, vacuum lines, brake lines as well
as a gas tank in the automobile. Make sure you know where they are when mounting
the amplifier to avoid puncturing lines, shorting wires or drilling holes in the gas tank.
Run signal wires away from electrical wires.
To avoid possibility of induced noise from the car's electrical system (i.e. popping noises
or engine noise), run wires away from the car's electrical wiring.
Make all ground wires as short as possible and at the same point.
In order to reduce the chance of ground loops (i.e. engine noise), make the grounding
wire as short as possible to reduce the wire's resistance. Also, when using multiple
components, make sure all units are grounded at the same point.
Avoid sharp edges when running the wires.
To avoid the possibility of power, signal or speaker shorts, be careful not to allow the
amplifier’s wires to come in contact with sharp edges. Use a grommet to protect the wire
when running through the fire wall .
ENGLISH
3
FEATURES AND BENEFITS
Digital Signal Processor
Built-in Digital Signal Processor that can be electronically controlled by the NXLCDC,
NXLI or NXCS (Sold Separately). The processor features the adjustment of gain, X-
over, tone, time delay, equalization.
DC Offset Protection
This circuit protects the output of the amplifier against DC voltage. If for some reason
DC voltage is detected at the output stage, the amplifier will shut down protecting the
speakers from direct current.
Short Circuit Protection
The circuit protects the amplifier from damage due to a short found in the speakers or
wiring. If one of the speakers or its wiring comes in contact with ground, the amplifier will
shut down. To resume normal operation, correct the problem and turn the head unit off,
then back on. The amplifier will reset and play again.
Thermal Protection
To protect the amplifier circuitry against damage caused by prolonged exposure to high
temperatures, a thermal protection circuit is activated if the amplifier reaches
excessively high operating temperature. Once the thermal circuit is activated, the
amplifier will shut down to cool off. The amplifier will automatically turn back on once it
cools down to a safe operating temperature.
Power / Protect Indicator
The power LED Illuminates blue when the amplifier is on and receiving power. The
protect LED Illuminates red when the amplifier has gone into protection mode.
Power Bridge Technology (NX1000.1 & 2000.1)
NXS’ Power Bridge technology gives you the flexibility to combine the power of two
NX1000.1 amplifiersor two NX2000.1 to double the output power into one speaker load.
High Level Input
High Level inputs have been included to connect the amplifier to a radio without low-
level outputs (i.e. factory radio).
Remote Auto Sensing for High Level Input
For added convenience when connecting to factory installed radio’s, the high level input
has a ‘Remote Auto Sensing” circuit allowing the amplifier to turn on when it receives
signal from the radio.
4
ENGLISH
Line Out (NX200.2, 400.2 , 400.4 & 500.1)
One set of full range line outputs have been provided for convenient connection to
additional amplifiers in the system.
Power Fusing
This protects the amplifier against short circuits and excessive current.
Remote Turn-on
Automatically turns amplifier on when connected to the head unit's remote output. The
amplifier will turn on and off with the head unit to save current consumption. This control
also operates the reset circuit for the amplifier's protection. It must be connected with
the head unit in order to reset protection circuits.
Adjustable Input Sensitivity
Allows you to fine-tune the level matching between your source and the power amplifier.
5
ENGLISH
MOUNTING LOCATION
Before you start the installation, it will be necessary to find a mounting location for the
amplifier. Find a location in which the amplifier will receive adequate ventilation in order
to dissipate the heat it develops during operation. Two popular mounting locations are
in the trunk or under the seat.
Select the location in which you wish to mount the amplifier. Use caution when
mounting amplifier, there are many wires, gas lines, vacuum lines, brake lines as well as
a gas tank in the automobile. Make sure you know where they are when mounting the
amplifier to avoid puncturing lines, shorting wires or drilling holes in the gas tank. Once
you are ready, use a pencil to mark the mounting holes in the bottom panel. After you
have marked the locations of the holes move amplifier out of the way and drill small
starter holes to make the tapping screws easier to install. Use provided screws to
tighten down the amplifier.
HIGH LEVEL
CH1&2
NX400.4
CH3&4
MAXMIN
INPUT
LEVEL
INPUTCH3CH1
CH4CH2
OUTPUT
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER
+12V REM GND
6
ENGLISH
POWER BRIDGE
POWER REMOTE
IN
GND +12V FUSE
HIGH
LEVEL INPUT
LEVEL
MIN MAX
INPUT
L
R
IN
OUT
PRT
MASTER
MODE
SLAVE PWR
SPEAKER
NX2000.1
80A
REMOTE
AUTO SENSING
ON
DSP NETLINK
IN OUT
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
OFF
ON
OFF
SW
LEVEL
CONTROL
FUSE
80A
POWER CONNECTIONS (NX2000.1)
IMPORTANT! Before making any connections, disconnect the car’s battery until
the installation is completed to avoid possible damage to the electrical system.
CAR BATTERY
+12V
--
++RADIO'S REMOTE
TURN-ON OUTPUT
“REMOTE AUTO SENSING” SWITCH
MUST BE IN THE “OFF” POSITION
FOR THE AMPLIFIER TO TURN ON
IN-LINE POWER FUSE
MOUNTED WITHIN 6"
FROM BATTERY RECOMMENDED
GROUND
(NOT PROVIDED)
Connect the amplifier to the car's battery.
At times, the amplifier will need to draw large levels of current that cannot be provided by
any circuit in the car's fuse box. We recommend using a 2 gauge power wire for your
connections depending on the amplifier and length of the wire. Strip one end of the wire
and connect to the terminal on the amplifier marked “+12V”. Loosen the set screw on
the terminal and insert wire and tighten. Use caution to make sure no stray wire strands
come in contact with surrounding terminals causing short circuits. Run the wire directly
to the positive terminal of the car's battery. Make sure to use an in-line fuse within 6” of
the car's battery to protect the electrical system and amplifier against short circuits
and/or power surges.
Connect the ground terminal of the amplifier to the car's chassis.
For the ground connection, use a 2 gauge wire (black) to connect to the terminal marked
“GND” and then connect it to the car's chassis. Try to keep the length of the cable as
short as possible, preferably less than 6". Make sure that the point on the car where the
connection is to be made is free of paint and dirt.
Connect the remote terminal of the amplifier to a switchable +12V source.
Please note: If you intend to use the high level inputs for your signal connections, we
provide a “Remote Auto Sensing” feature that will automatically turn-on the amplifier
when the high level inputs sense input signal. Please skip this step and see page 12.
This connection allows the amplifier to be turned on and off with the power control of the
radio. If the radio has a REMOTE output terminal, connect it to the amplifier's terminal
marked “REM” (using a 16 gauge wire or heavier). Now when the radio is turned on, the
amplifier will automatically turn on. When using this wire, the “REMOTE AUTO
SENSING” switch should be in the “OFF” position.
ENGLISH
7
POWER BRIDGE
POWER
REMGND +12V FUSE
REMOTE
AUTO SENSING
ON
DSP NETLINK
IN OUT
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
OFF
HIGH
LEVEL
ON
OFF
SW
LEVEL
CONTROL INPUT
LEVEL
MIN MAX
INPUT
L
R
IN
OUT
PRT
MASTER
MODE
SLAVE
PWR
SPEAKER
NX1000.1
100A
POWER CONNECTIONS (NX500.1, 900.5 )& 1000.1
IMPORTANT! Before making any connections, disconnect the car’s battery until
the installation is completed to avoid possible damage to the electrical system.
CAR BATTERY
+12V
--
++
RADIO'S REMOTE
TURN-ON OUTPUT
“REMOTE AUTO SENSING” SWITCH
MUST BE IN THE “OFF” POSITION
FOR THE AMPLIFIER TO TURN ON
IN-LINE POWER FUSE
MOUNTED WITHIN 6"
FROM BATTERY RECOMMENDED
GROUND
(NOT PROVIDED)
Connect the amplifier to the car's battery.
At times, the amplifier will need to draw large levels of current that cannot be provided by
any circuit in the car's fuse box. We recommend using a 4 gauge power wire for your
connections depending on the amplifier and length of the wire. Strip one end of the wire
and connect to the terminal on the amplifier marked “+12V”. Loosen the set screw on
the terminal and insert wire and tighten. Use caution to make sure no stray wire strands
come in contact with surrounding terminals causing short circuits. Run the wire directly
to the positive terminal of the car's battery. Make sure to use an in-line fuse within 6” of
the car's battery to protect the electrical system and amplifier against short circuits
and/or power surges.
Connect the ground terminal of the amplifier to the car's chassis.
For the ground connection, use a 4 gauge wire (black) to connect to the terminal marked
“GND” and then connect it to the car's chassis. Try to keep the length of the cable as
short as possible, preferably less than 6". Make sure that the point on the car where the
connection is to be made is free of paint and dirt.
Connect the remote terminal of the amplifier to a switchable +12V source.
Please note: If you intend to use the high level inputs for your signal connections, we
provide a “Remote Auto Sensing” feature that will automatically turn-on the amplifier
when the high level inputs sense input signal. Please skip this step and see page 12.
This connection allows the amplifier to be turned on and off with the power control of the
radio. If the radio has a REMOTE output terminal, connect it to the amplifier's terminal
marked “REM” (using a 16 gauge wire or heavier). Now when the radio is turned on, the
amplifier will automatically turn on. When using this wire, the “REMOTE AUTO
SENSING” switch should be in the “OFF” position.
8
ENGLISH
50A
DSP NETLINK
IN OUT
MAX
POWER
+12V REM GND
SPEAKERS
PWR
PRT
LRFUSE
BRIDGED
INPUT
L
OUTPUT
R
HIGH
LEVEL INPUT
LEVEL
MIN
L
R
NX400.2
REMOTE
AUTO SENSING
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS LEVEL
CONTROL
ON
ON OFF
OFF 84 2 1 A SW
POWER CONNECTIONS (NX200.2, 400.2 & 400.4)
IMPORTANT! Before making any connections, disconnect the car’s battery until
the installation is completed to avoid possible damage to the electrical system.
CAR BATTERY
+12V
--
++
RADIO'S REMOTE
TURN-ON OUTPUT
“REMOTE AUTO SENSING” SWITCH
MUST BE IN THE “OFF” POSITION
FOR THE AMPLIFIER TO TURN ON
IN-LINE POWER FUSE
MOUNTED WITHIN 6"
FROM BATTERY RECOMMENDED
GROUND
(NOT PROVIDED)
Connect the amplifier to the car's battery.
At times, the amplifier will need to draw large levels of current that cannot be provided by
any circuit in the car's fuse box. We recommend using a 4 or 8 gauge power wire for
your connections depending on the amplifier and length of the wire. Strip one end of the
wire and connect to the terminal on the amplifier marked “+12V”. Loosen the set screw
on the terminal and insert wire and tighten. Use caution to make sure no stray wire
strands come in contact with surrounding terminals causing short circuits. Run the wire
directly to the positive terminal of the car's battery. Make sure to use an in-line fuse
within 6” of the car's battery to protect the electrical system and amplifier against short
circuits and/or power surges.
Connect the ground terminal of the amplifier to the car's chassis.
For the ground connection, use a 4 or 8 gauge wire (black) to connect to the terminal
marked “GND” and then connect it to the car's chassis. Try to keep the length of the
cable as short as possible, preferably less than 6". Make sure that the point on the car
where the connection is to be made is free of paint and dirt.
Connect the remote terminal of the amplifier to a switchable +12V source.
Please note: If you intend to use the high level inputs for your signal connections, we
provide a “Remote Auto Sensing” feature that will automatically turn-on the amplifier
when the high level inputs sense input signal. Please skip this step and see page 12.
This connection allows the amplifier to be turned on and off with the power control of the
radio. If the radio has a REMOTE output terminal, connect it to the amplifier's terminal
marked “REM” (using a 16 gauge wire or heavier). Now when the radio is turned on, the
amplifier will automatically turn on. When using this wire, the “REMOTE AUTO
SENSING” switch should be in the “OFF” position.
ENGLISH
9
50A
DSP NETLINK
IN OUT
MAX
POWER
+12V REM GND
SPEAKERS
PWR
PRT
LRFUSE
BRIDGED
INPUT
L
OUTPUT
R
HIGH
LEVEL INPUT
LEVEL
MIN
L
R
NX400.2
REMOTE
AUTO SENSING
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS LEVEL
CONTROL
ON
ON OFF
OFF 84 2 1 A SW
POWER BRIDGE
POWER
REMGND +12V FUSE
REMOTE
AUTO SENSING
ON
DSP NETLINK
IN OUT
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
OFF
HIGH
LEVEL
ON
OFF
SW
LEVEL
CONTROL INPUT
LEVEL
MIN MAX
INPUT
L
R
IN
OUT
PRT
MASTER
MODE
SLAVE
PWR
SPEAKER
NX1000.1
100A
SIGNAL CONNECTIONS
Connect the RCA output of the head unit (AM/FM cassette player, CD, or DAT) to
the RCA input terminals of the amplifier.
To make these connections, we recommend high quality RCA cables, which are
available at your local car audio retailer. Run signal wires away from electrical wires to
avoid possibility of induced noise from the car's electrical system (i.e. popping noises or
engine noise). Please note that when making these connections the signal inputs
correspond with the speaker outputs.
LL
LL
LL
RR
Optional full range output
for additional amplifiers in
the system.
RR
RR
NX1000.1 & 2000.1 CONNECTIONS NX200.2, 400.2 & 500.1 CONNECTIONS
The NX400.4 allows for two or four channel input configurations. This gives the
flexibility of using only two channels of input and the amplifier automatically divides the
signal internally for four channels of output (Non Fading). The four channel input
configuration offers normal independent operation allowing for front and rear fading
capability through the head unit.
HIGH LEVEL
CH1&2
NX400.4
CH3&4
MAXMIN
INPUT
LEVEL
INPUTCH3CH1
CH4CH2
OUTPUT
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER
+12V REM GND
LL
RR
NX400.4 CONNECTIONS
USING TWO CHANNEL INPUT
LL
RR
Optional full range output
for additional amplifiers in
the system.
HIGH LEVEL
CH1&2
NX400.4
CH3&4
MAXMIN
INPUT
LEVEL
INPUTCH3CH1
CH4CH2
OUTPUT
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER
+12V REM GND
LL
RR
LL
RR
Optional full range output
for additional amplifiers in
the system.
LL
RR
NX400.4 CONNECTIONS
USING FOUR CHANNEL INPUT
10
ENGLISH
HIGH LEVEL
CH1&2
NX900.5
CH3&4 MAXMIN
INPUT
LEVEL
HIGH
LEVEL
CH3CH1
CH4CH2
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH5
CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER +12V
REMGND
CH5
CH5
INPUT
CH5
MAXMIN
INPUT
LEVEL FUSE
60A
POWER SPEAKER
The NX900.5 allows for two, four or five channel input configurations. This gives the
flexibility of using only two channels of input and the amplifier automatically divides the
signal internally for five channels of output (Non Fading). The four or five channel input
configuration offers normal independent operation allowing for front and rear fading
capability through the head unit.
LL
RR
NX900.5 CONNECTIONS
USING TWO CHANNEL INPUT NX900.5 CONNECTIONS
USING FOUR CHANNEL INPUT
HIGH LEVEL
CH1&2
NX900.5
CH3&4 MAXMIN
INPUT
LEVEL
HIGH
LEVEL
CH3CH1
CH4CH2
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH5
CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER +12V
REMGND
CH5
CH5
INPUT
CH5
MAXMIN
INPUT
LEVEL FUSE
60A
POWER SPEAKER
HIGH LEVEL
CH1&2
NX900.5
CH3&4 MAXMIN
INPUT
LEVEL
HIGH
LEVEL
CH3CH1
CH4CH2
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH5
CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER +12V
REMGND
CH5
CH5
INPUT
CH5
MAXMIN
INPUT
LEVEL FUSE
60A
POWER SPEAKER
LL
LL
RR
RR
LL
LL
RR
RR
LL
RR
FRONT REAR SUBREAR
NX900.5 CONNECTIONS
USING FIVE CHANNEL INPUT
11
ENGLISH
NX200.2 NX400.2 & NX1000.1 CONNECTIONS:
FLOATING GROUND RADIO (MOST COMMON TYPE)
High Level inputs have been included to connect the amplifier to a radio without low-
level outputs (i.e. factory radio). This connection will allow you to connect directly to the
speaker output of the radio without the need of an external adapter.
For added convenience when connecting to factory installed radio’s, the high level input
has a ‘Remote Auto Sensing” circuit allowing the amplifier to turn on when it receives
signal from the radio.
HIGH LEVEL CONNECTIONS (OPTIONAL)
POWER BRIDGE
POWER
REMGND +12V FUSE
REMOTE
AUTO SENSING
ON
DSP NETLINK
IN OUT
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
OFF
HIGH
LEVEL
ON
OFF
SW
LEVEL
CONTROL INPUT
LEVEL
MIN MAX
INPUT
L
R
IN
OUT
PRT
MASTER
MODE
SLAVE
PWR
SPEAKER
NX1000.1
100A
REMOTE
AUTO SENSING
ON OFF
RIGHT +RIGHT +
RIGHT +RIGHT +
RIGHT -RIGHT -
RIGHT -RIGHT -
LEFT -LEFT -
LEFT -LEFT -
LEFT +LEFT +
LEFT +LEFT +
WHITEWHITE
WHITE (CH3+)WHITE (CH3+)
GRAYGRAY
GRAY (CH4+)GRAY (CH4+)
WHITE/BLACKWHITE/BLACK
WHITE/BLACK (CH3 -)WHITE/BLACK (CH3 -)
GRAY/BLACKGRAY/BLACK
GRAY/BLACK (CH4-)GRAY/BLACK (CH4-)
HIGH LEVEL
CH1&2
NX400.4
CH3&4
MAXMIN
INPUT
LEVEL
INPUTCH3CH1
CH4CH2
OUTPUT
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER
+12V REM GND
RIGHT +RIGHT +
RIGHT -RIGHT -
LEFT -LEFT -
LEFT +LEFT +WHITE (CH1+)WHITE (CH1+)
GRAY (CH2+)GRAY (CH2+)
WHITE/BLACK (CH1-)WHITE/BLACK (CH1-)
GRAY/BLACK (CH2-)GRAY/BLACK (CH2-)
NX400.4 CONNECTIONS:
FLOATING GROUND RADIO (MOST COMMON TYPE)
The Remote Auto Sensing
Switch is in the “ON” position.
REMOTE
AUTO SENSING
ON OFF
The Remote Auto Sensing
Switch is in the “ON” position.
RCA Plugs
(Included)
The NX400.4 allows for 2 channel or 4
c h a n n e l h i g h l e v e l i n p u t
configurations. When you only
connect the CH1 & CH2 input, the
amplifier automatically divides the
signal internally for four channels of
output (Non Fading). If you are using
the 4 channel input configuration (as
shown), then you must use the
supplied RCA plugs for channel 3 & 4.
12
ENGLISH
RIGHT +RIGHT +
RIGHT -RIGHT -
LEFT -LEFT -
LEFT +LEFT +WHITE (CH5+)WHITE (CH5+)
GRAY (CH5+)GRAY (CH5+)
WHITE/BLACK (CH5 -)WHITE/BLACK (CH5 -)
GRAY/BLACK (CH5-)GRAY/BLACK (CH5-)
RIGHT +RIGHT +
RIGHT -RIGHT -
LEFT -LEFT -
LEFT +LEFT +WHITE (CH3+)WHITE (CH3+)
GRAY (CH4+)GRAY (CH4+)
WHITE/BLACK (CH3-)WHITE/BLACK (CH3-)
GRAY/BLACK (CH4-)GRAY/BLACK (CH4-)
NX900.5 CONNECTIONS:
USING FOUR OR FIVE CHANNEL INPUT
FLOATING GROUND RADIO (MOST COMMON TYPE)
REMOTE
AUTO SENSING
ON OFF
The Remote Auto Sensing
Switch is in the “ON” position.
The NX900.5 allows for 2 channel, 4 channel or 5 channel high level input
configurations. When you only connect the CH1 & CH2 input, the amplifier
automatically divides the signal internally for five channels of output (Non Fading).
13
HIGH LEVEL
CH1&2
NX900.5
CH3&4 MAXMIN
INPUT
LEVEL
HIGH
LEVEL
CH3CH1
CH4CH2
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH5
CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER +12V
REMGND
CH5
CH5
INPUT
CH5
MAXMIN
INPUT
LEVEL FUSE
60A
POWER SPEAKER
RIGHT +RIGHT +
RIGHT -RIGHT -
LEFT -LEFT -
LEFT +LEFT +WHITE (CH1+)WHITE (CH1+)
GRAY (CH2+)GRAY (CH2+)
WHITE/BLACK (CH1 -)WHITE/BLACK (CH1 -)
GRAY/BLACK (CH2-)GRAY/BLACK (CH2-)
HIGH LEVEL
CH1&2
NX900.5
CH3&4 MAXMIN
INPUT
LEVEL
HIGH
LEVEL
CH3CH1
CH4CH2
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH5
CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER +12V
REMGND
CH5
CH5
INPUT
CH5
MAXMIN
INPUT
LEVEL FUSE
60A
POWER SPEAKER
NX900.5 CONNECTIONS
USING TWO CHANNEL INPUT FLOATING GROUND RADIO (MOST COMMON TYPE)
RIGHT +RIGHT +
RIGHT -RIGHT -
LEFT -LEFT -
LEFT +LEFT +WHITEWHITE
GRAYGRAY
WHITE/BLACKWHITE/BLACK
GRAY/BLACKGRAY/BLACK
FRONT
REAR
SUB
REMOTE
AUTO SENSING
ON OFF
The Remote Auto Sensing
Switch is in the “ON” position.
(OPTIONAL CONNECTIONS)(OPTIONAL CONNECTIONS)
ENGLISH
POWER BRIDGE
POWER
REMGND +12V FUSE
REMOTE
AUTO SENSING
ON
DSP NETLINK
IN OUT
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
OFF
HIGH
LEVEL
ON
OFF
SW
LEVEL
CONTROL INPUT
LEVEL
MIN MAX
INPUT
L
R
IN
OUT
PRT
MASTER
MODE
SLAVE
PWR
SPEAKER
NX1000.1
100A
POWER
REMGND +12V FUSE
60A
DSP NETLINK
IN OUT
HIGH
LEVEL
REMOTE
AUTO SENSING
ON OFF
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
ON
OFF
SW
LEVEL
CONTROL INPUT
LEVEL
MIN MAX
NX500.1
SPEAKER
INPUT OUTPUT
R
L
PRT
PWR
Make the speaker connections using speaker wire that is at least 16 gauge or heavier.
As with any audio component, proper phasing of the amplifier and speakers is essential
for strong bass response. When connecting, make sure that positive (+) from the
amplifier is connected to the positive (+) of the speaker, and the same for negative (-).
we have
provided two sets of speaker terminals on the amplifier. These terminals are connected
in parallel internally (connected together). The second set of speaker terminals are
intended for ease of connection when running multiple woofers.
Please note that although the NX2000.1 and NX1000.1 are mono amplifiers,
SPEAKER CONNECTIONS
IMPORTANT! The speaker connections
shown for the NX1000.1 is a normal mono
configuration. If you are using more than
one NX1000.1 or NX2000.1 in a Power
Bridge configuration, please see speaker
connections in the Power Bridge section of
this manual.
(*1 Ohm Load)
Dual 4 Ohm Woofer Dual 4 Ohm Woofer
++
++
--
--
++
++
--
--
**CAUTION! The NX1000.1 and NX2000.1 must
see a 1 Ohm load or higher. Any lower than 1 Ohm
will cause the amplifier to overheat and possibly
cause permanent damage to the amplifier!
**CAUTION! The NX500.1
must see a 2 Ohm load or
higher. Any lower than 2 Ohm
will cause the amplifier to
overheat and possibly cause
permanent damage to the
amplifier!
NX1000.1 & NX2000.1 CONNECTIONS
14
Dual 4 Ohm Woofer (2 Ohm)
(2 Ohm Minimum)
++
++
--
--
NX500.1 CONNECTIONS
ENGLISH
HIGH LEVEL
CH1&2
NX900.5
CH3&4 MAXMIN
INPUT
LEVEL
HIGH
LEVEL
CH3CH1
CH4CH2
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH5
CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER +12V
REMGND
CH5
CH5
INPUT
CH5
MAXMIN
INPUT
LEVEL FUSE
60A
POWER SPEAKER
Dual 4 Ohm Woofer (2 Ohm)
(2 Ohm Minimum)
++
++
--
--
NX900.5 CONNECTIONS
SPEAKERS POWER
+12V REM GND
LR
PRT
PWR
NX200.2
HIGH
LEVEL
INPUT OUTPUT PRIMARY AMP
ADDRESS
REMOTE
AUTO SENSING
MULTI-AMP
ADDRESS LEVEL
CONTROL
ON
ON 84 2 1 A SW OFF
OFF
FUSE
25A
IN OUT
DSP NETLINK
BRIDGED
L
R
L
R
4 Ohm Speaker
(2 Ohm Minimum)
4 Ohm Speaker
(2 Ohm Minimum)
++
--
++
--
4 Ohm Speaker
(2 Ohm Minimum)
4 Ohm Speaker
(2 Ohm Minimum)
4 Ohm Speaker
(2 Ohm Minimum)
4 Ohm Speaker
(2 Ohm Minimum)
++
--
++
--
4 Ohm Speaker
(2 Ohm Minimum)
4 Ohm Speaker
(2 Ohm Minimum)
HIGH LEVEL
CH1&2
NX400.4
CH3&4
MAXMIN
INPUT
LEVEL
INPUTCH3CH1
CH4CH2
OUTPUT
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER
+12V REM GND
4 Ohm Speaker
(2 Ohm Minimum)
4 Ohm Speaker
(2 Ohm Minimum)
++
--
++
--
4 Ohm Speaker
(2 Ohm Minimum)
4 Ohm Speaker
(2 Ohm Minimum)
NX400.4 CONNECTIONS
NX200.2 & NX400.2 CONNECTIONS
**CAUTION! The NX900.5 must see a 2
Ohm load or higher. Any lower than 2
Ohm will cause the amplifier to overheat
and possibly cause permanent damage
to the amplifier!
15
ENGLISH
Adjustments of multiple amplifiers are made simple with NXS' proprietary DSP Netlink
system. Installation friendly RJ11 6 pin telephone cables make networking the
amplifiers a breeze. You can control up to 40 amplifiers with the NXLCDC in-dash
controller or using a NXLI and PC with NXCS control software. Amplifier addressing is
controlled by dip switches located at the front panel of every amplifier and once the
amplifier's address is set, users can choose which amp they want to
setup/adjust/control via the in-dash controller or PC.
A combination of four dip switches
can be used to set up to 10
different primary amplifier
addresses.
The “MULTI-AMP ADDRESS” switch allows up to 4 amplifiers to share the same address. The
factory default setting is in the “OFF” position for the use of only one amplifier. If more than one
amplifier share the same address the first amplifier is set to the “OFF” position and each additional
amplifier must be set to the “ON” position.
When using the two or four channel amplifiers to power
woofers, the “LEVEL CONTROL” switch is turned “ON”
allowing the output level of the amplifier to be controlled
by the NXLCDC or NXLC.
DSP NETLINK CONNECTIONS AND ADDRESSING
NOTE! The DSP NETLINK connections and adjustments require the NXLCDC in-
dash controller or the NXLI and PC with NXCS control software (Sold Separately).
50A
DSP NETLINK
IN OUT
MAX
POWER
+12V REM GND
SPEAKERS
PWR
PRT
LRFUSE
BRIDGED
INPUT
L
OUTPUT
R
HIGH
LEVEL INPUT
LEVEL
MIN
L
R
NX400.2
REMOTE
AUTO SENSING
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS LEVEL
CONTROL
ON
ON OFF
OFF 84 2 1 A SW
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS LEVEL
CONTROL
ON
OFF
84 2 1 A SW
ON
OFF
84 2 1
Address #1
ON
OFF
84 2 1
Address #2
ON
OFF
84 2 1
Address #3
ON
OFF
84 2 1
Address #4
ON
OFF
84 2 1
Address #5
ON
OFF
84 2 1
Address #6
ON
OFF
84 2 1
Address #7
ON
OFF
84 2 1
Address #8
ON
OFF
84 2 1
Address #9
ON
OFF
84 2 1
Address #10
PRIMARY AMP ADDRESS SETTINGS
VERY IMPORTANT! If only one amplifier is used for each address, the “MULTI-
LINK” switch must be in the “OFF” position (factory default) for the amplifier to be
controlled by the NXLCDC or NXLI.
16
ENGLISH
The following example shows a multiple amplifier installation adjusted by the optional
NXLCDC in dash controller. The NX400.4 powers four Mid/High speakers and two
NX1000.1’s power four woofers. The NX1000.1’s share the same DSP NETLINK
address so the amplifiers can be adjusted together.
If more than one amplifier share
the same address, one needs to
be set as the main amplifier for
the group. This is done by
setting the MULTI-AMP
ADDRESS to the OFF
position.
By default the level control for
the NX1000.1 is active at all
times regardless of the switch
position (This switch has no
function for the NX1000.1
only).
Because we already set the
NX1000.1 above as the main
amplifier, The MULTI-AMP
ADDRESS on this NX1000.1 is
set in the “ON” position.
Mid/High SpeakersMid/High Speakers
++
--
++
--
Mid/High SpeakersMid/High Speakers
HIGH LEVEL
CH1&2
NX400.4
CH3&4
MAXMIN
INPUT
LEVEL
INPUTCH3CH1
CH4CH2
OUTPUT
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER
+12V REM GND
ON
OFF
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS
Mid/High SpeakersMid/High Speakers
++
--
++
--
Mid/High SpeakersMid/High Speakers
NX400.4
INPUT
OUTPUT
Amplifier address
Is set at #1
NXLCDC
Amplifier address
is set at #2
NX1000.1
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
ON
OFF
SW
LEVEL
CONTROL
INPUT
POWER BRIDGE
POWER
REMGND +12V FUSE
REMOTE
AUTO SENSING
ON
DSP NETLINK
IN OUT
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
OFF
HIGH
LEVEL
ON
OFF
SW
LEVEL
CONTROL INPUT
LEVEL
MIN MAX
INPUT
L
R
IN
OUT
PRT
MASTER
MODE
SLAVE
PWR
SPEAKER
NX1000.1
100A
Dual 4 Ohm Woofer Dual 4 Ohm Woofer
++
++
--
--
++
++
--
--
NX1000.1 CONNECTIONS
NX1000.1
Amplifier address
is set at #2
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
ON
OFF
SW
LEVEL
CONTROL
By default the level control for
the NX1000.1 is active at all
times regardless of the switch
position (This switch has no
function for the NX1000.1
only).
INPUT
OUTPUT
POWER BRIDGE
POWER
REMGND +12V FUSE
REMOTE
AUTO SENSING
ON
DSP NETLINK
IN OUT
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
OFF
HIGH
LEVEL
ON
OFF
SW
LEVEL
CONTROL INPUT
LEVEL
MIN MAX
INPUT
L
R
IN
OUT
PRT
MASTER
MODE
SLAVE
PWR
SPEAKER
NX1000.1
100A
Dual 4 Ohm Woofer Dual 4 Ohm Woofer
++
++
--
--
++
++
--
--
17
ENGLISH
POWER BRIDGE
POWER
REMGND +12V FUSE
REMOTE
AUTO SENSING
ON
DSP NETLINK
IN OUT
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
OFF
HIGH
LEVEL
ON
OFF
SW
LEVEL
CONTROL INPUT
LEVEL
MIN MAX
INPUT
L
R
IN
OUT
PRT
MASTER
MODE
SLAVE
PWR
SPEAKER
NX1000.1
100A
POWER BRIDGE CONNECTIONS (OPTIONAL)
NXS’ Power Bridge technology gives you the flexibility to combine the power of two
NX1000.1 amplifiers or two NX2000.1 amplifiers to double the output power into one
speaker load.
The “Master” amplifier controls the level, crossover, equalization, subsonic filter for both the
master and slave amplifier.
IMPORTANT! In Power Bridge operation, both amplifiers must be the same model of equal
power.
POWER BRIDGE
POWER
REMGND +12V FUSE
REMOTE
AUTO SENSING
ON
DSP NETLINK
IN OUT
8A
4 2 1
PRIMARY AMP
ADDRESS MULTI-AMP
ADDRESS
OFF
HIGH
LEVEL
ON
OFF
SW
LEVEL
CONTROL INPUT
LEVEL
MIN MAX
INPUT
L
R
IN
OUT
PRT
MASTER
MODE
SLAVE
PWR
SPEAKER
NX1000.1
100A
NX1000.1
++
--
NX1000.1
NXLCDC
LL
RR
MASTER
MODE
SLAVE
MASTER
MODE
SLAVE
MODE IS SET TO “SLAVE”
POSITION
MODE IS SET TO
“MASTER” POSITION
2 Ohm Minimum
**CAUTION! In the Power Bridge configuration the pair of NX1000.1’s or NX2000.1’s must see
a 2 Ohm load or higher. Any lower than 2 Ohm will cause the amplifiers to overheat and possibly
cause permanent damage to the amplifiers!
18
ENGLISH
NX1000.1 & NX2000.1 CONNECTIONS
REMOTE LEVEL CONTROL (OPTIONAL)
The overall level of the amplifier can be adjusted using the NXLCDC or NXLC (sold
separately). Unlike conventional level controls (Also known as Sub Level Controls), the
NXS level control is an intelligent circuit allowing you to select which amplifier and/or
channels you would like to remotely control. Additionally only one remote is needed to
control multiple amplifiers.
The following example shows a NX400.4 amplifier with channels 1 & 2 running the mid
and high speakers and channels 3 & 4 bridged running a single woofer. The level
control has been turned “ON” for channels 3 & 4 so the woofer can be adjusted remotely
by the level control (NXLCDC or NXLC).
++
--
Woofer
HIGH LEVEL
CH1&2
NX400.4
CH3&4
MAXMIN
INPUT
LEVEL
INPUTCH3CH1
CH4CH2
OUTPUT
ON
OFF
L
R
DSP NETLINK
IN OUT
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS REMOTE
AUTO SENSING
ON OFF
SPEAKERS
BRIDGED
CH2CH1 CH3
BRIDGED
PRT
PWR
CH4 FUSE
60A
POWER
+12V REM GND
ON
OFF
8A4 2 1/2
13/4
PRIMARY AMP
ADDRESS LEVEL
CONTROL
MULTI-AMP
ADDRESS
Mid/High Speakers
++
--
++
--
Mid/High Speakers
NX400.4
INPUT
LEVEL CONTROL IS
SWITCHED “ON” FOR
CHANNELS 3 & 4
NXLCDC
NXLC
CONTROL THE SUB LEVEL WITH
NXLCDC OR NXLC
LEVEL CONTROL IS
SWITCHED “OFF” FOR
CHANNELS 1 & 2
PLEASE NOTE: If a NX500.1, NX1000.1 or NX2000.1 is used in the system, the
amplifier’s output level is automatically controlled by the NXLC or NXLCDC .
19
ENGLISH
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

NXS NX1000.1 Installation Instructions & Owner's Manual

Kategorie
Auto-Audio-Verstärker
Typ
Installation Instructions & Owner's Manual

in anderen Sprachen