USER’S MANUAL
Safety, Operation and Maintenance
TJ12
HYDRAULIC
TRACK JACK
(10 TON)
© 2017 Stanley Black & Decker, Inc.
New Britain, CT 06053
U.S.A.
72713 12/2022 Ver. 10
European Union
Rue de la Loi/Wetstraat 175
B-1048 Bruxelles/Brussel
Belgique/België
2 ► TJ12 User Manual
DECLARATION OF CONFORMITY
DECLARATION OF CONFORMITY
ÜBEREINSTIMMUNGS-ERKLARUNG
DECLARATION DE CONFORMITE CEE
DECLARACION DE CONFORMIDAD
DICHIARAZIONE DI CONFORMITA
______________________________________________________________________
I, the undersigned:
Ich, der Unterzeichnende:
Je soussigné:
El abajo firmante:
lo sottoscritto:
Vervier, Patrick
Surname and First names/Familiennname und Vornamen/Nom et prénom/Nombre y apellido/Cognome e nome
hereby declare that the equipment specified hereunder:
bestätige hiermit, daß erklaren Produkt genannten Werk oder Gerät:
déclare que l’équipement visé ci-dessous:
Por la presente declaro que el equipo se especifica a continuación:
Dichiaro che le apparecchiature specificate di seguito:
1. Category: Track Jack
Kategorie:
Catégorie:
Categoria:
Categoria:
2. Make/Marke/Marque/Marca/Marca STANLEY
3. Type/Typ/Type/Tipo/Tipo: TJ12111S, TJ12112S
4. Serial number of equipment:
Seriennummer des Geräts:
Numéro de série de l’équipement:
Numero de serie del equipo:
Matricola dell´attrezzatura:
All
Has been manufactured in conformity with
Wurde hergestellt in Übereinstimmung mit
Est fabriqué conformément
Ha sido fabricado de acuerdo con
E’ stata costruita in conformitá con
Directive/Standards
Richtlinie/Standards
Directives/Normes
Directriz/Los Normas
Direttiva/Norme
No.
Nr
Numéro
No
n.
Approved body
Prüfung durch
Organisme agréé
Aprobado
Collaudato
Machinery Directive
EN
2006/42/EC:2006
1494:2000/A1:2008
Self
Self
5. Special Provisions: None
Spezielle Bestimmungen:
Dispositions particulières:
Provisiones especiales:
Disposizioni speciali:
6. Representative in the Union: Patrick Vervier, STANLEY Dubuis 17-19, rue Jules Berthonneau- CS 73406 41034 Blois CEDEX, France.
Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione
Done at/Ort/Fait à/Dado en/Fatto a STANLEY Infrastructure, Milwaukie, Oregon USA Date/Datum/le/Fecha/Data
Signature/Unterschrift/Signature/Firma/Firma
Position/Position/Fonction/Cargo/Posizione Engineering Manager
11/08/2022
TJ12 User Manual ◄ 3
DECLARATION OF CONFORMITY
______________________________________________________________________
I, the undersigned:
Vervier, Patrick
Surname and First names
hereby declare that the equipment specified hereunder:
1. Category: Track Jack
2. Make: STANLEY
3. Type: TJ12111S, TJ12112S
4. Serial number of equipment:
All
Has been manufactured in conformity with
Directive/Standards
No.
Approved body
EN
Supply of Machinery
(Safety) Regulations
2008
1494:2000+A1:2008
S.I. 2008/1597
Self
Self
5. Special Provisions: None
6. Representative in the Union: Patrick Vervier, STANLEY Dubuis 17-19, rue Jules Berthonneau- CS 73406 41034 Blois CEDEX, France.
Done at STANLEY Infrastructure, Milwaukie, Oregon USA Date
Signature
Position Engineering Manager
11/08/2022
4 ► TJ12 User Manual
TABLE OF CONTENTS
SERVICING: This manual contains safety, operation and routine maintenance instructions. STANLEY Infrastructure
recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized
and certied dealer. Please read the following warning.
To ll out a product warranty validation form, and for information on your warranty,
visit www.stanleyinfrastructure.com and select the Company tab > Warranty.
Note: The warranty validation record must be submitted to validate the warranty.
SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR
SERVICE OF THIS TOOL.
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN
AUTHORIZED AND CERTIFIED DEALER.
For the nearest certied dealer, call STANLEY Infrastructure at (503) 659-5660 and ask for a Customer Service Representative.
SAFETY SYMBOLS .................................................................................................................................................5
TOOL STICKERS AND TAGS .................................................................................................................................8
MAINTENANCE & CARE ........................................................................................................................................9
OPERATING INSTRUCTIONS ............................................................................................................................. 12
TROUBLESHOOTING ..........................................................................................................................................14
SPECIFICATIONS ................................................................................................................................................15
PUMP ASSEMBLY ILLUSTRATION & PARTS LIST ...........................................................................................16
BASE ILLUSTRATION & PARTS LIST .................................................................................................................17
TJ12 User Manual ◄ 5
Always observe safety symbols. They are included for your safety and for the protection of the tool.
LOCAL SAFETY REGULATIONS
Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and
maintenance personnel.
Safety symbols and signal words, as shown below, are used to emphasize all operator, maintenance and repair
actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equipment.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible
injury or death.
This safety alert and signal word indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
This safety alert and signal word indicates a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
This safety alert and signal word indicates a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
This signal word indicates a potentially hazardous situation which, if not avoided,
may result in property damage.
This signal word indicates a situation which, if not avoided, will result in damage
to the equipment.
This signal word indicates a situation which, if not avoided, may result in damage
to the equipment.
SAFETY SYMBOLS
6 ► TJ12 User Manual
SAFETY PRECAUTIONS
Tool operators and maintenance personnel must
always comply with and work in accordance with the
safety precautions and instructions given in this manual
and on the stickers and tags attached to the tool and
hose.
These precautions are given for your safety. Review
them carefully before operating the tool and performing
general maintenance or repairs.
Supervising personnel should develop additional
precautions relating to the specic work area and local
safety regulations. Place the added precautions in the
space provided.
• The TJ12 conforms with EN 1494:2000+A1:2008.
This jack is intended for only the lifting of rail
(railroad tracks) and should never be used for any
other purpose other than what it was intended for
or personal injury could result.
• The user must be familiar with correct operation,
maintenance and use of the jack. Lack of
knowledge can lead to personal injury.
• Operator must start in a work area without
bystanders. The operator must be familiar with all
prohibited work areas such as excessive slopes,
dangerous terrain conditions and extreme climates.
• Always wear safety equipment such as goggles,
gloves, head protection and safety shoes at all
times when operating the tool.
• Warning: Hydraulic uid under pressure could
cause skin injection injury. If you are injured by
hydraulic uid, get medical attention immediately.
• The total load lifted or supported by the jack must
never exceed the rated capacity. Excess pressure
can result in personal injury. Use a jack with
sucient capacity to lift a load. Keep clear of lifted
loads.
• Before each use, visually inspect the jack to
prevent unsafe conditions from developing. Do not
use jacks that are damaged, leaking, altered or in
poor condition. See “INSPECTING THE TRACK
JACK FOR DAMAGE OR LEAKAGE” on page
11
• Properly support the jack.
• Do not put poorly balanced or o-center loads
on the jack pad or jack. The load can tip and
cause personal injury. Do not use in unstable or
hazardous positions.
• The jack must be used on at surfaces to be able
to carry the load correctly. The base must be
completely supported. Do not push or lift on the
ends of the base.
• Do not lift people or loads with people on them.
• As the load is lifted, use blocks or cribs to guard
against a falling load.
• To prevent personal injury, do not allow personnel
to go under, or work under or on a load before it is
properly secured by suitable means. All personnel
must be clear of a load before lowering or lifting.
• Lift only dead weight loads. Do not add additional
weight to a lifted load.
• Do not use jacks that are damaged, altered or in
poor condition. Do not modify the jack in any way
that would aect the compliance of the jack with
standard BS EN 1494:2000+A1:2008.
• The reservoir must have sucient hydraulic
uid to fully stroke the jack. Use only approved
hydraulic uids. Also make sure that there is no
contaminations of oil on the oor or working area
• Read and understand the operating instructions
in this manual, and the ASME B30.1 and EN 1494
safety code for jacks.
• Users must ensure that all safety related decals
and stickers are whole and readable. Replace
those which become unreadable.
• Never use extreme heat to disassemble a hydraulic
ram or cylinder. Metal fatigue can lead to unsafe
conditions.
• Be aware of possible "pinch points" on the jack and
stay clear to avoid personal injury.
• When lifting with the edge of the lifting toe, place a
wedge between the load and the top of the lifting
TJ12 User Manual ◄ 7
toe to avoid bending the cylinder column.
• Carry the jack by the carrying handle. Make sure
the jack is in the fully lowered position before
moving.
• End users must be trained in the proper use of the
jack. Fully lower the jack when work is completed.
• Remove operating levers when not in use to avoid
accidental dislocation of the jack, and reduce the
tripping hazard.
• Make sure all personnel are clear of the load
before lifting or lowering.
• DO NOT use extenders, spindles or accessories.
Injury or death could result.
• Never use this tool when working around electried
rail, unless it is de-energized or you have been
properly trained to work on electried rail. If you are
not sure the rail is live or not, you must treat it as
being live and dangerous to life.
• The operator should always have the lifting device
and load in view during movement.
• To avoid personal injury or equipment damage,
all tool repair, maintenance and service must only
be performed by authorized and properly trained
personnel.
• Never use the tool in an explosive atmosphere.
Sparks could ignite explosive gas.
• Never use the tool near strong magnetic elds.
• Do not handle loads, the nature of which could lead
to dangerous situation (e.g. molten metal, acids,
radiating material or especially brittle loads).
• When decommissioning the jack, drain all hydraulic
uid and dispose of the uid in accordance with
state and federal regulations.
• If the rated values are exceeded, use additional
persons to aid in lowering.
SAFETY PRECAUTIONS
8 ► TJ12 User Manual
TOOL STICKERS AND TAGS
RAILROAD HELP
DESK STICKER
P/N-73680
IMPORTER STICKER
P/N-88345
MANUAL STICKER
P/N-88348
CRUSHING HAZARD
P/N-31064
STANLEY STICKER
P/N-73679
Note: The following information can be found on the
bottom left side of the base. Model Number, Serial
Number, 7250 PSI/500 Bar and year of manufacture
are stamped in this location on each jack.
CE STICKER
P/N-28322 UKCA STICKER
P/N-88724
TJ12 User Manual ◄ 9
MAINTENANCE & CARE
GENERAL PROTECTION
• Store the Track Jack in an upright position, in a
place where it is protected from the elements,
abrasive dust and damage. Do not exceed the
rated use temperatures of -4°F - 122ºF (-20°C -
50°C).
• TJ12 is rated for use at temperatures between -4°F
- 122ºF (-20°C - 50°C).
• Use only recommended repair and replacement
parts and materials specied in the Parts List
section of this manual.
• Do not use the jack for applications it was not
designed for.
• Use the carrying handle to transport the Track Jack
from location to location. Do not carry the Track
Jack by inserting the jack handle in the socket.
CLEANING
• Establish a routine to keep the jack as free from
dirt as possible – daily, or at each shift change, for
example.
• Jacks exposed to rain, sand or grit-laden air should
be cleaned prior to each use.
• Exposed screw threads should be cleaned and re-
lubricated as necessary.
• Keep the cylinder clean at all times. Keep the
piston retracted when not in use.
• Operating lever and loadbearing surfaces should
be free of slippery material or uids.
• Keep tool labels and stickers legible.
HYDRAULIC FLUID
The Track Jack holds approximately 28 ounces/820 cc
cubic inches of hydraulic uid (ISO#15) in its reservoir.
Do not use brake uid or other non-
approved substitute uids. Lighter weight
uids may cause the jack to fail under load.
A jack that is low on hydraulic uid will still be able to lift
a full load, but not to the full lift height. As the reservoir
begins to run dry, the handle lever becomes very easy
to pump and the jack stops lifting. This is a sign the
jack is low on uid.
To add oil:
1. Fully retract the plunger.
2. Make sure relief valve is closed.
3. Remove the ll plug (item # 3 on the Pump
Assembly Illustration).
4. Fill the reservoir with new, clean uid (use ISO#15
Hydraulic Fluid). Fill completely to the bottom of the
threads on the ll plug hole.
DO NOT OVERFILL OR UNDERFILL THE
RESERVOIR AS THIS MAY DAMAGE THE JACK.
ANNUAL FLUID CHANGE
Track Jack hydraulic uid should be changed every
year to ensure proper operation of the jack.
To drain the uid:
1. Thoroughly clean the area around the ll plug.
2. Remove the ll plug and lay the Track Jack on its
back to allow the uid to drain from the ll hole into
an appropriate receptacle.
3. Dispose of the used hydraulic uid in accordance
with Environmental Protection Agency regulations.
4. Make sure dirt or other contaminants do not enter
the reservoir while the ll plug is removed. When
drained, check the uid for contaminants. If the
uid appears gritty or dirty, ush the reservoir with
clean hydraulic uid before relling.
5. Rell the reservoir with the recommended hydraulic
uid. Stand the jack upright, with the piston fully
retracted. Fill the reservoir completely to the bottom
of the threads on the ll plug hole.
6. Before returning the jack to service, fully extend
the piston, without a load, by pumping the pump
handle without the long extension handle. If the
10 ► TJ12 User Manual
MAINTENANCE & CARE
uid level is correct, the pump handle will become
almost impossible to pump by hand as the piston
reaches full extension.
7. Replace the plug.
8. Inspect the jack for leaks, cracks, or other damage.
Immediately take out of service any jack
that appears to be damaged or leaking.
PURGING AIR
Air trapped within the jack hydraulic system can be
removed by performing the following steps:
1. Make sure the plunger is fully retracted.
2. Pry out the cap (see illustration at right).
3. Loosen (Do Not Remove) the capscrew under the
cap located in the top of the plunger.
4. Place the jack in a suitable xture to prevent the
extension of the plunger while purging air.
The xture used to prevent extension of the
plunger while purging air must be able to
withstand the full ten ton force of the jack.
5. Add hydraulic uid to the reservoir, if necessary.
6. Pump the handle until oil comes up through the
thread area of the capscrew in the plunger.
7. Tighten the socket head capscrew to 10-12 ft.
lbs./14-16 Nm. Then replace the cap.
8. Top o the reservoir with hydraulic uid.
Note: Make sure the plunger is fully retracted
before lling the reservoir.
Oil Fill Plug
When purging, remove
cap and loosen. Do not
remove the socket head
capscrew that is under the
cap.
Cap
PRESSURE RELIEF SETTING
The pressure relief is pre-set at the factory and should
never be altered. After the pressure relief is set at
the factory the adjustment screw is made to not be
tampered with.
If you have any issues with the relief setting, please
contact STANLEY and ask for a Customer Service
Representative.
The pressure relief is pre-set at the factory,
never attempt to alter it’s setting. Altering
the relief setting could result in death,
serious injury or equipment damage.
To avoid personal injury or equipment
damage, all tool repair, maintenance
and service must only be performed by
authorized and properly trained personnel.
TJ12 User Manual ◄ 11
MAINTENANCE & CARE
INSPECTING THE TRACK JACK FOR
DAMAGE OR LEAKAGE
1. Before each use, visually inspect the jack for leaks,
cracks or other damage.
Never use a damaged track jack.
Immediately take out of service any jack
that appears to be damaged or leaking and
replace any damaged parts.
Retaining Ring
Cap
Lifting Toe
2. Once a month, remove the retaining ring and lifting
toe. Thoroughly inspect the back, as well as the
front and sides, for damage or cracks. Take special
note of the areas indicated above.
12 ► TJ12 User Manual
OPERATING INSTRUCTIONS
Make sure that all personnel are clear of
the load before attempting to raise or lower
the jack. Serious injury or death could result
from the improper use of this tool.
PREPARATION PROCEDURES
Before putting a new Track Jack into service, or after
an extended period of being unused, perform a visual
inspection for bent, broken, cracked, missing or worn
components. (see “INSPECTING THE TRACK JACK
FOR DAMAGE OR LEAKAGE” on page 11.
Ensure the hydraulic uid and lubricant level is correct.
Fully extend and retract the jack without a load to
ensure that the jack is primed and operating properly.
Note: TJ12 is rated for use at temperatures between
-4°F - 122ºF (-20°C - 50°C).
RAISING A LOAD
1. Before using the Track Jack, make sure that it
is set on a rm surface capable of bearing the
intended load.
2. Make sure the Spindle (item 41) is closed, by
turning it clockwise until it is hand-tight.
Overtightening the spindle (item 41) can
damage the valve seat. DO NOT use pliers
or wrenches to tighten.
3. Pump the handle by hand until the toe lift or head
lift plate rises and engages the load.
Head Lift
Toe Lift
Make certain that the lifting toe is fully
engaged on the load, and the entire jack is
stable, before proceeding further.
4. Insert the jack handle fully into the handle socket.
Pump until the desired lift has been obtained.
Use only the recommended length jack
handle. DO NOT use longer handles. See
“SPECIFICATIONS” on page 15.
5. Remove the jack handle from the handle socket.
6. Crib or block the load to prevent accidental
dropping of the load.
LOWERING A LOAD
1. Make sure all personnel are clear of the load.
2. Remove cribbing or blocking, if used.
3. Slowly open the spindle (item 41) by turning it
counterclockwise.
Lowering speed is controlled by opening
the Spindle more or less. Open slowly
to control the lowering speed. Caution:
Opening the Spindle too much will cause
the load to drop quickly.
4. When the load reaches the desired level, close the
spindle by turning it clockwise until it is hand tight.
HORIZONTAL OPERATION
The Track Jack can also be used horizontally to
separate two items, as long as it is placed with the
handle socket facing upwards.
1. Place the Track Jack base against the largest,
heaviest or otherwise least moveable of the two
items.
2. Close the spindle (item 41) by turning it clockwise
until hand tight.
3. Pump the handle socket by hand until the lifting
TJ12 User Manual ◄ 13
toe or the head of the lifting toe rmly engages the
more moveable of the two items.
4. Make sure personnel are clear of all items being
jacked before attempting to move anything.
5. Insert the jack handle into the handle socket. Pump
until the desired separation has been obtained.
6. Remove the jack handle from the socket.
7. To free the jack, open the spindle by turning it
counterclockwise. When the lift plate is clear, close
the spindle.
8. The operator must watch the lifting device and the
load during all movements.
Never lift or lower a load heavier than the
load rating of the jack. Damage to the jack
or load could result from improper use of
this tool.
PUMPING HANDLE
A pumping handle is included with the Track Jack. DO
NOT use the pumping handle for any other purpose.
DO NOT substitute other material for use as a pumping
handle or use a longer handle than what is specied on
“SPECIFICATIONS” on page 15
OPERATING INSTRUCTIONS
14 ► TJ12 User Manual
TROUBLESHOOTING
If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem.
Because the Track Jack can be used for many dierent applications, this information is general in nature and
does not address specic uses.
PROBLEM CAUSE CORRECTION
Jack will not raise
A) Release valve not closed Close the valve
B) Release valve ball not
seating properly Have jack serviced by a qualied technician
C) Seal failure Have jack serviced by a qualied technician
Jack raises but will not hold
A) Release valve ball not
seating properly
B) Relief valve set too low
or malfunctioning
Have jack serviced by a qualied technician
C) Seal failure Have jack serviced by a qualied technician
Jack only raises part way Hydraulic uid level is low Add hydraulic uid (See “SPECIFICATIONS”
on page 15)
Jack leaks hydraulic uid Seal failure Have jack serviced by a qualied technician
Jack retracts slowly Air in the hydraulic system Purge air from the hydraulic system
Jack raises, but pulses and
hesitates Air in the hydraulic system Purge air from the hydraulic system
TJ12 User Manual ◄ 15
SPECIFICATIONS
PERFORMANCE
Maximum Lift .................................................................................................................................... 8.8 in. / 22.3 cm
Maximum Load ............................................................................................................................... 10 tons / 9,072 kg
Pump Displacement ........................................................................................46 cu. in. / 7.5 cc stroke, single speed
Advance rate per stroke ................................................................................................................. 0.160 in. / 4.0 mm
Pressure at rated load ................................................................................................ 7250 psi / 500 bar Model TJ12
Maximum pump handle eort ................................................................................................................75 lbs. / 34 kg
DIMENSIONS
Baseplate Size TJ12111S ..................................................................................................6.000 x 11 in. / 15 x 28 cm
Baseplate Size TJ12112S Narrow .................................................................................. 4.500 x 11 in. / 11.4 x 28 cm
Weight ................................................................................................................................................45 lbs / 19.5 kg
Lift Toe Width and Depth ..........................................................................................2-1/2 in x 3 in. / 63 mm x 76 mm
Height (Retracted) .......................................................................................................................... 14.7 in. / 37.3 cm
Height (Extended) ....................................................................................................................... 23.500 in. / 597 mm
Net Weight (with oil) no handle ..................................................................................................... 45 lb / 20.4 kg
Pump Handle Length (p/n-52813) ........................................................................................................ 36 in. / 91 cm
HYDRAULIC REQUIREMENTS
Reservoir Capacity ...............................................................................................................................28 oz / 828 cc
Recommended Fluid ........................................................................................................... ISO #15 Hydraulic Fluid.
Standards ...................................................................................................................... ASME B30.1, EN 1494:2009
Note: This product does not exceed 70 dBA per ISO 11201
Note: Weights, dimensions and operating specications listed on this sheet are subject to change
without notice. Where specications are critical to your application, please consult the factory.
REPAIR KITS
Note: For items in repair kits see both illustrations and parts lists.
Cylinder Repair Kit.............................................................................................................................................56522
Includes Items: 1, 7, 19, 21, & 27 thru 31.
Reservoir Repair Kit ..........................................................................................................................................56524
Includes Items: 25, 26 and 35
PUMP HANDLE
ASSEMBLY P/N-52813
16 ► TJ12 User Manual
PUMP ASSEMBLY ILLUSTRATION & PARTS LIST
TJ12111S
TJ12112S Narrow Base
* DENOTES PART IN
SEAL KIT (P/N-72735)
(see both parts list for
items included in seal kit)
For Cylinder Repair Kit & Reservoir
Repair kit see page 13.
Model #, Serial #
Located here.
Complete Pump
Assembly P/N-
74864
ITEM PART # QTY DESCRIPTION
1 00055 2 O-RING *
2 01671 1 -6 HEX HD SAE PLUG
3 04855 1 RETAINING RING EXTERNAL
5 05291 1STEEL BALL 7/32
6 07327 1 O-RING *
7 15398 2 BACK-UP RING *
8 21338 1 STEEL BALL 5/32
9 26005 1 # 80 MASTER LINK
10 26039 1 O-RING *
11 28322 1 STICKER "CE" 12MM
12 88348 1 STICKER - MANUAL
25 52831 1 BLADDER
26 52832 1 RESERVOIR
33 56517 1 ROD WIPER *
34 56518 4 CAPSCREW
35 56521 4 CAPSCREW
36 71431 1 COMPRESSION COIL
SPRING
37 71478 1 OIL TUBE
38 74863 1 PUMP BODY (INCLUDES
EXPANDER PLUGS)
38A 74864 1PUMP ASSY (INCLUDES
ITEMS 1-64 & 16)
39 71707 1 O-RING *
40 72663 1 CHECK VALVE SEAT ASSY
(INCLUDES ITEM 6)
41 71715 1 SPINDLE
42 71716 1 PISTON
43 76751 1 RELIEF VALVE SEAT-COINED
44 71738 1 SELF LOCKING SETSCREW
46 72664 1 CHECK VALVE HOUSING
ASSY (INCLUDES ITEM 60)
48 73679 1 NAME TAG - TJ12
49 73680 1 RR HELP DESK STICKER
51 76494 1 BACK-UP RING *
53 76697 1 HANDLE (INCLUDES DU
BUSHINGS)
56 76716 1 GROOVED CLEVIS PIN
57 76717 1 SCREW
58 76718 1 SPRING SEAT
60 76773 1 O-RING *
61 76817 1 RELIEF VALVE ASSEMBLY
(RELIEF IS PRE SET AT
FACTORY)
62 79297 1 ORIFICE, TJ12 DESCENT
63 79301 1 SHIELD, ORIFICE
64 350023 2 HOLLOW HEX PLUG -3 SAE
65 88724 1 UKCA STICKER
38A
TJ12 User Manual ◄ 17
1
2
3 6
7
9
8
12
14
16
17
18
19
20
21
22
23
25
26
27
28
29
30
31
32
51 33 34
35
37
38
39
40
41
42
43
44
46
48
49
60
55
11
10
56
36
58
57 4
19
60
24
BASE ILLUSTRATION & PARTS LIST
TJ12111S
For Cylinder Repair Kit &
Reservoir Repair kit see
“Repair Kits” on page
15.
Model #, Serial #
Located here.
* DENOTES PART IN SEAL KIT P/N-72735
(see both parts list for items included in seal kit)
ITEM PART # QTY DESCRIPTION
14 31064 1 CRUSHING HAZARD
DECAL
16 52805 1 CAP ASSY.
17 52806 1 LIFTING TOE
18 52807 1 STOP RING
19 52808 2 GASKET *
20 52809 1 PLUNGER
21 52810 1 BEARING
22 52811 1 SPRING ASSEMBLY
23 52812 1 BASE TJ12
23A 56601 1BASE (TJ12112S)
27 56506 1 RETAINING RING *
28 56507 1 ROD WIPER *
29 56508 1 ROD SEAL *
30 56509 1 BACK-UP RING *
31 56510 1 O-RING *
32 56512 1 HSHCS M6-1.0 X 25
55 76714 1 HSHCS M6-1.0 X 80
23A
European Union
Rue de la Loi/Wetstraat 175
B-1048 Bruxelles/Brussel
Belgique/België
Stanley Infrastructure
3810 SE Naef Road
Milwaukie, Oregon 97267-5698 USA
(503) 659-5660 / Fax (503) 652-1780
www.stanleyinfrastructure.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
