Endres+Hauser EA Alteration Display module to Display module Mounting Instruction

Products Solutions Services

Installation Instructions

Alteration Display module to

Display module with WLAN

Proline 300, 400, 500, 500-digital

EA01158D/06/A2/08.23-00

71601542

2024-01-01

EA01158D

Endress+Hauser 3

Altering an existing display to display with WLAN

Proline 300, 400, 500, 500-digital

Table of contents

1 Overview of alteration kit .......................................................... 4

2 Persons authorized to alter the device .............................................. 5

3 Personnel authorized to fit new nameplates ........................................ 5

4 Intended use ...................................................................... 5

5 Safety instructions ................................................................ 6

6 Symbols .......................................................................... 7

7 Tools list .......................................................................... 7

8 Altering the blind version of the transmitter to a transmitter with a display module

and cover with window for Proline 300 ............................................. 8

9 Altering the transmitter with a display module to a transmitter with a display

module and WLAN interface and external antenna for Proline 300, 500 ............. 9

10 Altering the transmitter with a display module to a transmitter with a display

module and WLAN interface and external antenna for Proline 300, 500-digital ..... 13

11 Operating options and characteristics of WLAN antenna ........................... 20

12 Modifications to the product roots and extended order codes in the CER database on

Engine .......................................................................... 22

13 Disposal ......................................................................... 23

EA01158D

4 Endress+Hauser

1 Overview of alteration kit

The installation instructions apply to the following alteration kits:

Product structure Upgrade Alteration kit (contents)

Alteration kits for Proline 300

DKZ001–****AF*** Transmitter without display

To transmitter

With display

1 × display with ribbon cable

1 × display holder

1 × cover with window, 1 × O-ring

1 × wired-on tag plate, 1 × conversion

instructions

DKZ001–****AG*** Transmitter without display

To transmitter

With display and WLAN interface

1 × display with ribbon cable and WLAN

interface

1 × display holder

1 × cover with window

1 × O-ring, 1 × wired-on tag plate

1 × conversion instructions

DKZ001–****FG***+P8 Transmitter with display

And WLAN interface

To transmitter

With display and WLAN interface

including external antenna

1 × display with ribbon cable and WLAN

interface including external antenna and

cable gland

1 × wired-on tag plate,

1 × conversion instructions

Alteration kits for Proline 500

DKZ002–****FGB*** Transmitter with display

To transmitter with display and WLAN

interface

1 × display with ribbon cable and WLAN

interface

1 × wired-on tag plate

1 × conversion instructions

DKZ002–****FGB***+P8 Transmitter with display

To transmitter with display and WLAN

interface including external antenna

1 × WLAN display with ribbon cable and

WLAN interface including external antenna

and cable gland

1 × wired-on tag plate

1 × conversion instructions

Alteration kits for Proline 500-digital

DKZ002–****FGA*** Transmitter with display to transmitter

with display and WLAN interface

1 × WLAN display with ribbon cable and

WLAN interface

1 × wired-on tag plate

1 × conversion instructions

DKZ002–****FGA***+P8 Transmitter with display to transmitter

with display and WLAN interface

including external antenna

1 × WLAN display with ribbon cable and

WLAN interface including external antenna

and cable gland

1 × wired-on tag plate

1 × conversion instructions

EA01158D

Endress+Hauser 5

2 Persons authorized to alter the device

Authorization to perform alterations is dependent on the approval of the measuring device.

The table below shows the authorized group of people in each case.

Measuring device approval Personnel authorized to carry out conversions 1)

Without approval 1, 2, 3

With approval (e.g. IECEx) 1, 2, 3

For custody transfer 4

1) 1 = Qualified specialist on customer side, 2 = Service technician authorized by Endress+Hauser,

3 = Endress+Hauser (return measuring device to manufacturer)

4 = Check with local approval center if installation/conversion or alteration must be performed under supervision.

3 Personnel authorized to fit new nameplates

Measuring device approval Personnel authorized to apply new nameplates 1)

Without approval 2, 3

With approval (e.g. IECEx) 2, 3*

1) 2 = service technician authorized by Endress+Hauser, 3 = Endress+Hauser (return device to manufacturer)

* Note: Some countries/markets require a field inspection in order to change

nameplates. Please act in accordance with national legislation.

4 Intended use

• Alteration kits and installation instructions are used to upgrade certain functions of an

Endress+Hauser measuring device.

• Only use original parts from Endress+Hauser.

• Check in the W@M Device Viewer if the alteration kit is suitable for the measuring device in

question.

EA01158D

6 Endress+Hauser

=

www.endress.com/deviceviewer

Order code Description

Ser. No.: 12345...

=

5 Safety instructions

• Only use original parts from Endress+Hauser.

• Comply with national regulations governing mounting, electrical installation,

commissioning, maintenance and alteration.

• The specialized technical staff involved in the mounting, electrical installation,

commissioning, maintenance, installation and alteration of the measuring devices must

meet the following requirements:

• Specialized technical staff must be trained in instrument safety.

• Specialized technical staff must be familiar with the individual operating conditions of the

devices.

• In the case of Ex-certified measuring devices, they must also be trained in explosion

protection.

• The measuring device is energized! Risk of fatal injury from electric shock. Open the

measuring device only when the device is de-energized.

• For measuring devices intended for use in hazardous locations, please observe the

guidelines in the Ex documentation (XA).

• For measuring devices in safety-related applications in accordance with IEC 61508 or

IEC 61511: following alteration, re-commission the device in accordance with the Operating

Instructions. Document the alteration.

• Before removing the device: set the process to a safe state and purge the pipe of dangerous

process substances.

• Risk of injury from hot surfaces! Before commencing work: allow the system and measuring

device to cool to a touch-safe temperature.

• In the case of devices in custody transfer, the custody transfer status no longer applies once

the seal has been removed.

• The Operating Instructions for the device must be followed.

• Risk of damaging electronic components! Ensure you have a working environment

protected from electrostatic discharge.

• After removing the electronics compartment cover: risk of electrical shock due to missing

touch protection!

Turn the measuring device off before removing internal covers.

• Only open the housing for a short period. Avoid foreign objects, moisture or dirt entering

the housing.

EA01158D

Endress+Hauser 7

• Replace defective seals only with original seals from Endress+Hauser.

• If threads are defective, the measuring device must be repaired.

• Threads (e.g. of the electronics compartment cover and connection compartment cover)

must be lubricated if an abrasion-proof dry lubricant is not available. Use acid-free, non-

hardening lubricant.

• If, during alteration, spacing is reduced or the dielectric strength of the measuring device

cannot be guaranteed, perform a test on completion of the work (e.g. high-voltage test in

accordance with the manufacturer's instructions).

• Service connector:

• Do not connect in potentially explosive atmospheres.

• Only connect to Endress+Hauser service devices.

• Observe the instructions for transporting and returning the device outlined in the Operating

Instructions.

If you have any questions, please contact your responsible www.addresses.endress.com.

6 Symbols

6.1 Symbols for certain types of information

Symbol Meaning

Permitted

Procedures, processes or actions that are permitted.

Forbidden

Procedures, processes or actions that are forbidden.

Tip

Indicates additional information.

1.

,

2.

,

3.

… Series of steps

7 Tools list

Allen key

3 mm

Torx screwdriver

T20

Slotted head

screwdriver

0.5 x 3.5 mm

Hexagon wrench Crimping tool

EA01158D

8 Endress+Hauser

8 Altering the blind version of the transmitter to a

transmitter with a display module and cover with

window for Proline 300

1 → 2 →

2.

3 mm

1.

3.

icht unter

Spannung öffnen

Do not open when

energized

sous tension

Power

Ne pas ouvrir

N

I/O

2.5 Nm (1.8 lbf ft)

N

i

c

ht

u

n

t

e

r

a

r

e

ö

f

n

e

n

3 → 4

+E

ESC

–

2.

3.

2. 1.

ö

f

n

e

n

a

r

e

N

i

c

ht

u

n

t

e

r

N

i

c

ht

u

n

t

e

r

ö

f

n

e

n

a

r

e

3 mm

1.

2.5 Nm (1.8 lbf ft)

2.

3.

EA01158D

Endress+Hauser 9

9 Altering the transmitter with a display module to a

transmitter with a display module and WLAN interface

and external antenna for Proline 300, 500

The external WLAN antenna is not suitable for use in hygienic applications.

1 → 2 →

N

i

c

ht

u

n

t

e

r

ö

f

n

e

n

a

r

e

3.

2.

1. 3 mm

+E

ESC

–

ö

f

n

e

n

a

r

e

N

i

c

ht

u

n

t

e

r

3.

1.

2.

3 → 4 →

5 → 6 →

2.

1.

30 mm

4 Nm

2.

1.

ESC

EA01158D

10 Endress+Hauser

7 → 8 →

9 → 10 →

+E

ESC

–

2.

3.

2. 1.

ö

f

n

e

n

a

r

e

N

i

c

ht

u

n

t

e

r

N

i

c

ht

u

n

t

e

r

ö

f

n

e

n

a

r

e

3 mm

1.

2.5 Nm (1.8 lbf ft)

2.

3.

11

EA01158D

Endress+Hauser 11

9.1 Mounting the wireless antenna with cable

3.

1.

2.

5.

4.

For detailed information on the electrical connection, see the "Electrical connection"

section of the Operating Instructions for the device.

For detailed information on commissioning, see the "Commissioning" section of the

Operating Instructions for the device.

EA01158D

12 Endress+Hauser

9.2 Modifying the label

9.2.1 Checking the data on tie-on label:

• Device serial number

• New order code

• Attach tie-on label as per the diagram using wire cable and crimp barrels:

1

EA01158D

Endress+Hauser 13

10 Altering the transmitter with a display module to a

transmitter with a display module and WLAN interface

and external antenna for Proline 300, 500-digital

10.1 Aluminum transmitter housing

The external WLAN antenna is not suitable for use in hygienic applications.

1 →

T20

1.

2.

2 →

-+-

ESC

2.

1.

3 →

-+-

ESC

2.

1.

EA01158D

14 Endress+Hauser

4 → 5 →

1.

2.

30 mm

4 Nm

6 → 7 →

8 → 9 →

3.

1.

-+-

ESC

2.

1.

2.

-+-

ESC

EA01158D

Endress+Hauser 15

10 → 11

T20

1.

2.

10.2 Polycarbonate transmitter housing

The external WLAN antenna is not suitable for use in hygienic applications.

1 →

T20

1.

2.

2 →

-+-

ESC

2.

1.

EA01158D

16 Endress+Hauser

3 →

-+-

ESC

2.

1.

4 → 5 →

1.

2.

30 mm

4 Nm

6 → 7 →

‣Route the antenna cable through

the guide on the rear of the

display.

EA01158D

Endress+Hauser 17

8 → 9 →

3.

1.

-+-

ESC

2.

1.

2.

-+-

ESC

‣Plug in the display connector (1), guide the ribbon cable for the display

behind the tab on the module bracket (2), secure the display (3).

‣Route the antenna cable into the

side of the transmitter housing

(1), fold down the electronics

compartment cover (2).

10 → 11

2.

T20

1.

3.

EA01158D

18 Endress+Hauser

10.3 Mounting the wireless antenna with cable

3.

1.

2.

5.

4.

For detailed information on the electrical connection, see the "Electrical connection"

section of the Operating Instructions for the device.

For detailed information on commissioning, see the "Commissioning" section of the

Operating Instructions for the device.

EA01158D

Endress+Hauser 19

10.4 Modifying the label

10.4.1 Checking the data on tie-on label:

• Serial number of device

• New order code

• Attach tie-on label as per the diagram using wire cable and crimp barrels:

1

10.4.2 Fit the nameplate:

Fit the nameplate (optional) according to the existing device labeling (see also Section 3

→  5 Authorized persons).

EA01158D

20 Endress+Hauser

11 Operating options and characteristics of

WLAN antenna

1 2 3

4 5 6

1 Transmitter with external WLAN antenna

2 LED lit constantly: WLAN reception is enabled on measuring device

3 LED flashing: WLAN connection established between operating unit and measuring device

4 Computer with WLAN interface and web browser (e.g. Microsoft Internet Explorer, Microsoft Edge)

for accessing integrated device web server or operating tool (e.g. FieldCare, Device Care)

5 Mobile handheld terminal with WLAN interface and web browser (e.g. Microsoft Internet Explorer,

Microsoft Edge) for accessing integrated device web server or operating tool

(e.g. FieldCare, Device Care)

6 Smartphone or Tablet (e.g. Field Xpert SMT70)

Function WLAN: IEEE 802.11 b/g (2.4 GHz)

• Access Point with DHCP server (factory setting)

• Network

Function WLAN: IEEE 802.11 b/g (2.4 GHz)

• Access Point with DHCP server (factory setting)

• Network

Encryption WPA2-PSK AES-128 (in accordance with IEEE 802.11i)

Configurable WLAN channels 1 to 11

Degree of protection IP67

Available antennas • Internal antenna

• External antenna (optional)

In the event of poor transmission/reception conditions at the place of

installation.

Available as an accessory .

Only 1 antenna is active at any one time!

Seite laden ...

Endres+Hauser EA Alteration Display module to Display module Mounting Instruction

Endres+Hauser EA Alteration Display module to Display module Mounting Instruction

in anderen Sprachen

Verwandte Papiere