Avantree SLP-370 Benutzerhandbuch

Typ
Benutzerhandbuch
A
C
H
Model No.: SLP-370
Avantree Slumber
User Manual
EN User Manual
DE Benutzerhandbuch
FR Manuel de L’Utilisateur
ES Manual de Usuario
IT Manuale Utente
2
15
28
41
54
SLUMBER
User Manual
1
Table of Contents
Box Contents
Product Introduction
Product Overview
Button Functions
LED Indicators
Getting Started
Choosing an Audio Mode
MP3 Mode
AUX Mode
Bluetooth Mode
Setting a Sleep Timer
Specications
FAQ
Contact Us
3
4
4
5
6
7
8
8
9
10
11
12
13
14
SLUMBER
User Manual
2
EN
Box Contents
A B
CD
D
H
Slumber Cushion Slumber Speakers
Remote Control Aux 3.5 Audio Cable
SLUMBER
User Manual
3
EN
Product Introduction
Product Overview
1ON/OFF
2Bluetooth
mode /
PAIRING
button
8Replay /
previous
track button
6Volume
adjustment
3MP3 / AUX
mode swap button
9Timer
setup button
Front
Back
4PLAY / PAUSE
5EQ mode
swap button
7Skip button
Bluetooth
connection
indicator
Playback
mode
indicator
B
Timer
indicator
C
A
10 Stereo/mono
switch
AUX mode
indicator
D
EQ indicator
E
STEREO MONO
SLUMBER
User Manual
4
EN
Button Functions
Switch to turn the Slumber on / o
No. Button Functions
Press once to enter Bluetooth mode or to
manually reconnect to the last-paired device
Press & hold for 2 seconds to enter pairing mode
Press once to enter AUX / MP3 mode
Press & hold for 2 seconds to switch among
ordered / single cycle / shue playback
modes (MP3 only)
Press once to switch between clear voice /
well-balanced audio modes
Turn to adjust volume
Press once to skip / replay track (Bluetooth /
MP3 only)
Press & hold both buttons for 10 seconds to clear
pairing history
Press once to cycle through sleep timer options
(30 mins / 1hr / 2hr) or to cancel the timer
Switch to put the Slumber in stereo / mono
mode (stereo mode splits audio between L &
R speakers; mono mode combines audio signals
so L & R speakers both receive the same audio)
Press once to play / pause music
ON OFF
1
2
3
4
5
6
7
8
9
10 STEREO MONO
SLUMBER
User Manual
5
EN
A
B
C
D
E
LED Indicators
Ordered / single cycle / shue playback
mode (MP3 only)
Solid white for 30
seconds then o
Alternate red &
blue ashes
Solid blue for 30
seconds then o
Solid white for 30
seconds then o
Solid white for 30
seconds then o
Solid white for 30
seconds then o
No. Indicator Status
Pairing
Connected
Timer on
AUX mode
Clear voice mode
SLUMBER
User Manual
6
EN
In order to avoid disturbing your sleep, all LED indicators will turn
o after 30 seconds.
ON OFF
Getting Started
The two speakers facing upward
SLUMBER
User Manual
7
EN
You can use the Slumber by either placing it on top of your existing
pillow, or by inserting it into your pillow cover. Make sure both
speakers are facing upwards.
STEP 1
The Slumber must be connected to a power source via the
provided power cable in order to function. Plug the provided type C
charging cable into the charging port, then connect the other end
to a 5V/500mA-2A rated USB adapter (your phone charger or similar
should work) or PC USB port.
STEP 2
Slide the switch to the ON” position to turn the Slumber on.
(5V/1A-2A) (not included)
SLUMBER
User Manual
8
EN
Choosing an Audio Mode
You can choose to stream audio in three dierent ways: via MP3,
Bluetooth, or AUX. The Slumber will default to the last-used mode
each time it’s powered on.
MP3 Mode
For rst time use, the Slumber will enter MP3 mode automatically,
playing the built-in white noises. If not, press the button
once to enter MP3 mode manually. You can change the playback
mode by pressing & holding the button until the
corresponding indicator turns solid white.
The Slumber contains a built-in 4GB storage card that it uses while
in MP3 mode. In addition to the 10 enclosed white noise options,
you can upload your own tracks by connecting the Slumber to your
PC via the included USB C cable. Transfer your chosen les to the
Avantree Slumber” disc and enjoy!
Ordered playback
Single cycle playback
Shue playback
Solid white
for 30 seconds
SLUMBER
User Manual
9
EN
AUX Mode
Plug the AUX 3.5mm audio cable into both the Slumber and your
audio output device (i.e. your phone / PC / tablet), and the Slumber
will enter AUX mode automatically. If not, press once to
swap from MP3 mode or twice if you're swapping from Bluetooth
mode.
NOTE: The and buttons do not work in AUX mode.
D
Avantree Slumber
SLUMBER
User Manual
10
EN
Bluetooth Mode
STEP 1
Press the button once to enter Bluetooth mode. For rst time
use, the Slumber will enter PAIRING mode automatically. If not, put
your Slumber into PAIRING mode by pressing & holding the
button until the LED ashes blue and red alternately.
STEP 2
Turn on your device's Bluetooth and select "Avantree Slumber" in
the Bluetooth menu.
STEP 3
Keep them close and wait for 5-10 seconds or until they connect.
Once connected, the Slumber’s Bluetooth connection indicator will
turn solid blue.
For subsequent use, the Slumber should automatically reconnect to
the last-paired device within a few seconds of being switched to
Bluetooth mode. If not, you can manually activate reconnection by
tapping the button once, or by selecting "Avantree Slumber" in
your device's Bluetooth menu.
NOTE: You'll need to adjust the volume on both the Slumber &
your audio device to reach the lowest volume level.
SLUMBER
User Manual
11
EN
30 mins
1 hour
2 hours
Setting a Sleep Timer
The sleep timer can be set to make the Slumber automatically turn
o after a specied amount of time. You can choose among 30 mins,
1 hour, or 2 hours by pressing the button. The corresponding
LED will light up to indicate your selection.
SLUMBER
User Manual
12
EN
v5.3Bluetooth version
Supported proles
Frequency response
Audio input level
Rated Input
Operating range
Fabric
Product dimensions
Net weight
A2DP; AVRCP
20Hz-20KHz
1000mV
DC5V/500mA-2.0A
Polyester nylon
28mm drivers, 4Ω, 3W
400mm x 135mm x 15mm
215g
Up to 30ft / 10m
Specications
Speakers
SLUMBER
User Manual
13
EN
FAQ
Below are some of the most common questions people have during
setup.
Is the pillow washable?
Yes, you can wash the pillow by hand whenever necessary. Please
take out the speakers before washing. When re-assembling, make
sure that the main speakers are facing upwards. You can nd more
specic directions on re-assembling at
avantree.com/support/slumber/install.
I turned the volume down as low as possible -- why can
someone else still hear?
Make sure to adjust the volume on both your device and the
Slumber in order to reach the lowest volume levels. If the sound is
still leaking, you can consider resting your ear directly on top of the
speaker and turning the volume down even further.
You can nd a full FAQ list at avantree.com/support/slumber, or
contact us directly for additional assistance.
SLUMBER
User Manual
14
EN
Contact Us
Support Tickets avantree.com/submit-a-ticket
Support Email [email protected]
FAQ avantree.com/support/slumber
USA / CA +1800 232 2078 (9am-6pm PST, Mon-Fri )
UK +44 20 8068 2023 (9am-6pm, GMT, Mon-Sat)
DE +49 32221097297 (11am-9pm, CET, Mon-Sat )
FR + 33 176340312 (11am-9pm, CET, Mon-Sat )
IT +39 06 9480 3330 (9am-6pm, CET, Mon-Sat )
ES + 34 931786261 (9am-6pm, CET, Mon-Sat )
AU + 61 2 8310 9897 (11am-7pm, AEST, Mon-Fri)
Product Registration avantree.com/product-registration
Video Guide avantree.com/slumber/video
Live Chat avantree.com (18/h weekday)
Inhaltsübersicht
Verpackungsinhalt
Produkteinführung
Produktübersicht
Tastenfunktionen
LED Anzeige
Erste Schritte
Auswahl eines Audiomodus
MP3-Modus
AUX Modus
Bluetooth Modus
Einstellen eines Einschlaf-Timers
Technische Daten
FAQ
Kontakt
16
17
17
18
19
20
21
21
22
23
24
25
26
27
DE
SLUMBER
User Manual
15
Verpackungsinhalt
A B
CD
D
H
Schlummerkissen Slumber Lautsprecher
Steuerung Aux 3.5 Audiokabel
DE
SLUMBER
User Manual
16
Produkteinführung
Produktübersicht
1EIN/AUS
2Bluetooth
-Modus /
PAIRING-Taste
zum koppeln
8Taste für
Wiederholung
/vorherigen Titel
6
Lautstärkeeinstellung
3Umschalttaste für
MP3-/AUX-Modus
9Taste für die
Timereinstellung
Vorderseite
Rückseite
4WIEDERGABE
/ PAUSE
5Taste zum
Umschalten
des EQ-Modus
7Überspringen-
Taste
Bluetooth
Verbindungsanzeige
Wiedergabemodus-
Anzeige
B
Timer
Anzeige
C
A
10 Stereo/Mono
-Umschalter
Anzeige für
AUX-Modus
D
EQ-Anzeige
E
STEREO MONO
DE
SLUMBER
User Manual
17
Tastenfunktionen
Schalter zum Ein- und Ausschalten des
Schlummers
Nr. Taste Funktionen
Drücken Sie einmal, um in den Bluetooth-Modus
zu wechseln oder um die Verbindung zum zuletzt
gekoppelten Gerät manuell wiederherzustellen
Halten Sie die Taste 2 Sekunden lang gedrückt,
um den Kopplungsmodus zu aktivieren.
Einmal drücken, um in den AUX/MP3-Modus zu
gelangen
Drücken und halten Sie für 2 Sekunden, um
zwischen den Wiedergabemodi "In der
Reihenfolge", "Einzelschleife" und "Zufällige
Wiedergabe" umzuschalten (nur MP3).
Einmal drücken, um zwischen den Modi "Klarer
Sprachmodus" und "Ausgewogener
Audio-Modus" umzuschalten.
Zum Einstellen der Lautstärke drehen
Einmal drücken, um den Titel zu überspringen /
zu wiederholen (nur Bluetooth / MP3)
Halten Sie beide Tasten 10 Sekunden lang
gedrückt, um den Kopplungsverlauf zu löschen.
Drücken Sie einmal, um durch die Schlaf-Timer-
Optionen zu navigieren (30 Minuten / 1 Stunde /
2 Stunden) oder um den Timer abzubrechen.
Schalter, um den Slumber in den Stereo-/Mono-
Modus zu versetzen (im Stereo-Modus werden
die Audiosignale zwischen den linken und
rechten Lautsprechern aufgeteilt; im Mono-
Modus werden die Audiosignale kombiniert, so
dass die linken und rechten Lautsprecher beide
den gleichen Ton erhalten)
Einmal drücken, um Musik abzuspielen oder auf
Pause zu schalten
ON OFF
1
2
3
4
5
6
7
8
9
10
STEREO MONO
DE
SLUMBER
User Manual
18
A
B
C
D
E
LED Anzeigen
Wiedergabemodus "In der
Reihenfolge" / "Einzelzyklus" / "
Zufällig" (nur MP3).
30 Sekunden lang
durchgehend weiß,
danach werden sie
ausgeschaltet.
Abwechselndes Blinken
in Rot und Blau.
30 Sekunden lang
durchgehend Blau,
danach werden sie
ausgeschaltet.
30 Sekunden lang
durchgehend Weiß,
danach werden sie
ausgeschaltet.
30 Sekunden lang
durchgehend Weiß,
danach werden sie
ausgeschaltet.
30 Sekunden lang
durchgehend Weiß,
danach werden sie
ausgeschaltet.
Nr. Anzeige Status
Koppeln
Verbunden
Timer ein
AUX Modus
Klarer Sprachmodus
DE
SLUMBER
User Manual
19
Um Ihren Schlaf nicht zu stören, werden alle LED-Anzeigen nach 30
Sekunden automatisch ausgeschaltet.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Avantree SLP-370 Benutzerhandbuch

Typ
Benutzerhandbuch