Buffalo Technology AirStation WLI-U2-SG54HG Benutzerhandbuch

QUICK SETUP GUIDE

www.bualotech.com

EN DE FR IT ES PT NL SV

NO

DA FI

WLI-U2-SG54HG

AirStation Wireless USB Adapter

1

EN

AirStation Wireless USB Adapter (WLI-U2-SG54HG)

Package contents includes:

• WLI-U2-SG54HG Adapter

• USB 2.0 Cable

• Quick Setup Guide

• Setup CD-ROM

• Warranty Statement

Thank you for purchasing a Bualo AirStation Wireless USB Adapter.

• Insert the AirNavigator CD into the CD-ROM drive of your computer.

The AirNavigator Setup Wizard should launch automatically.

• To launch the AirNavigator Setup Wizard manually, click Start, then Run.

Type “D:\Setup.exe”, where D is the drive letter assigned to your CD-ROM.

• Click OK to launch the wizard.

Package Contents

Getting Started

1

Fig: 1

EN

2

Installing Drivers

2

• Select Install Wireless Drivers.

Fig: 2

Installing Drivers

2

• Click Next to install a driver for the USB adaptor. (Fig: 3)

• Review the license agreement. Select Agree and click Next to continue

installation. (Fig: 4)

• A window will appear prompting the insertion of the Wireless Adapter.

Plug the included cable into the AirStation Wireless USB Adapter and your

PC’s USB port. (Fig: 5)

Fig: 3

3

EN

Installing Drivers

2

Fig: 4

Fig: 5

USB Port

Wireless USB

Adapter

EN

4

Installing Drivers

2

• When the ‘Found New Hardware Wizard’ launches, click Next to run the

wizard. (Fig: 6)

• If the ‘Digital Signature Not Found’ page opens, click Yes. (Fig: 7)

• When the Wireless USB Adapter is successfully installed, click Finish. Restart

your computer if prompted. (Fig: 8)

Fig: 6

Fig: 7

5

EN

The WLI-U2-SG54HG includes a built-in directional antenna. For best

performance, point the antenna at your access point as shown.

External antennas cannot be attached to the WLI-U2-SG54HG.

Antenna Information

3

Fig: 8

Installing Drivers

2

EN

6

Installing Client Manager

4

Fig: 9

Buffalo’s Client Manager software lets you survey and connect to any

supported wireless networks. It also allows for one touch setup and

configuration via AOSS.

To install Client Manager, click on Install Client Manager and follow the wizard

through the setup.

Click on Exit Setup to exit AirNavigator.

Client Manager is now installed and running. Double-click on its icon (the

black antenna) to use it.

Fig: 10

7

EN

Using Client Manager To Connect To Your Wireless Network

5

If your router/AP supports AOSS, you can set up your wireless network by

pushing two buttons. Turn to the next page.

Alternatively, you can set up your wireless connections manually:

• Click the Scan tab in Client Manager. It will show you a list of available

networks.

• Choose the network you want to connect to and click Connect.

• If the chosen wireless network is encrypted, select the Encryption Method,

enter one or more encryption keys, and click Connect.

Fig: 11

Fig: 12

Note: If you only have one encryption key, enter it in the first (#1) field.

EN

8

AOSS (AirStation One-Touch Secure System) is a simple way to connect

wireless clients to a Bualo wireless router or access point while enforcing

the most secure encryption possible. Users no longer need to worry

about choosing the proper security protocols, IP addresses, or SSID. AOSS

determines the optimal connection and congures itself in seconds. Once

AOSS has been setup, your other devices will need to be connected to the

wireless network by performing AOSS or by manually adding the device to

the wireless network. Please consult the user manual that came with your

AOSS Wireless Router or Access Point to retrieve the necessary connection

information.

The AOSS button for the WLI-U2-SG54HG is in its Client Manager software,

Start Client Manager by right clicking on the black antenna icon in your

System Tray, or by launching the Client Manager from your Start Menu:

Programs >> Bualo >> AirStation Utility >> Client Manager.

Using AOSS To Connect To Your Network

6

Fig: 13

9

EN

Using AOSS

7

• From the Status Screen, select the Proles tab.

• Click the blue AOSS button on the Client Manager’s screen. The AOSS

wizard will appear.

• Now, press the AOSS button on the Access Point. Hold it down until the

AOSS LED begins to ash.

Fig: 14

EN

10

Using AOSS

7

Once AOSS is complete (about 30 seconds), the connection is archived as a

prole for later use. To minimize Client Manager to the system tray, click the

‘X’ in the top right corner.

Notes: AOSS will scan for an AOSS partner for about two minutes. If it times

out before nding one, just press the AOSS buttons again.

Output power is reduced to 25% of normal during AOSS for security reasons.

If you’re having trouble making an AOSS connection, temporarily move the

devices closer together.

AOSS will automatically use the highest level of security available for all

currently connected wireless devices.

If you have trouble connecting with AOSS, temporarily disable all personal

rewalls on your PC, such as ZoneAlarm or Microsoft Personal Firewall. These

programs may be re-enabled after AOSS has nished.

Fig: 15

Fig: 17

Fig: 16

11

EN

Europe - EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive

1999/5/EC. The following test methods have been applied in order to prove

presumption of compliance with the R&TTE Directive 1999/5/EC:

EN 60950-1:2001

Safety of Information Technology Equipment

EN 300328 V1.6.1:2004

Technical requirements for spread-spectrum radio equipment

EN 301489-1 V1.6.1:2005, EN301 489-17 V1.2.1:2002

EMC requirements for spread-spectrum radio equipment.

Intended use

This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home

and oce use in all EU and EFTA member states.

EU Countries intended for use

This device is intended for indoor Home and oce use in the following

countries:

Austria, Belgium, Germany, Denmark, Spain, Greece, France, Finland, Italy,

Ireland, Luxembourg, The Netherlands, Portugal, Sweden, United Kingdom,

Cyprus, Czech Republic, Estonia, Hungry, Latvia, Lithuania, Malta, Poland,

Slovak Republic and Slovenia.

The device is also authorised for use in all EFTA member states Iceland,

Liechtenstein, Norway and Switzerland.

EU countries not intended for use

None

Potential restrictive use

This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home

and oce use in all EU and EFTA member states, except in France, Belgium

and Italy where restrictive use applies.

In Italy the end-user should apply for a license at the national spectrum

authorities in order to obtain an authorization to use the device for setting up

outdoor radio links.

In Belgium there is a restriction in outdoor use. The frequency range in which

outdoor operation in Belgium is permitted is 2460 – 2483.5 MHz.

This device may not be used for setting up outdoor radio links in France. For

more information see http://www.anfr.fr/ and/or http://www.art-telecom.fr

EN

12

Environmental Information

• The equipment that you have purchased has required the extraction and

use of natural resources for its production.

• The equipment may contain hazardous substances that could impact health

and the environment.

• In order to avoid the dissemination of those substances in our environment

and to diminish

the pressure on the natural resources, we encourage you to use the

appropriate take-back systems.

• The take-back systems will reuse or recycle most of the materials of your end

life equipment in a sound way.

• The crossed-out wheeled bin symbol invites you to use those systems.

• If you need more information on the collection, reuse and recycling systems,

please contact your local or regional waste administration.

Contact Details

Address: Bualo Technology UK LTD

176, Buckingham Avenue,

Slough, Berkshire, SL1 4RD

United Kingdom

General Inquiries:

Email

sales@bualo-technology.com

Technical Support:

Helpdesk Hours Monday-Thursday 9:00 AM - 6:00 PM

Friday 9:00 AM - 4:30 PM

Phone +353 61 70 80 50

Phone (UK only) 08712 50 12 60

Email helpdesk@bualo-technology.ie

13

DE

AirStation Wireless-USB-Adapter (WLI-U2-SG54HG)

Der Packungsinhalt umfasst:

• WLI-U2-SG54HG-Adapter

• USB 2.0-Kabel

• Handbuch für die Schnellinstallation

• Installations-CD-ROM

• Garantieerklärung

Vielen Dank, dass Sie sich für den Bualo AirStation Wireless-USB-Adapter

entschieden haben!

• Legen Sie die AirNavigator-CD in das CD-ROM-Laufwerk des Computers ein.

Der AirNavigator-Installationsassistent sollte automatisch gestartet werden.

• Um den AirNavigator-Installationsassistenten manuell zu starten, klicken Sie

auf Start und dann auf Ausführen.

Geben Sie „

D:\Setup.exe“ ein, wobei „D“ der Ihrem CD-ROM-Laufwerk

zugeordnete Laufwerksbuchstabe ist.

• Klicken Sie auf OK, um den Assistenten zu starten.

Packungsinhalt

Erste Schritte

1

Abb. 1

DE

14

Installieren der Treiber

2

• Wählen Sie Install Wireless Drivers (Wireless-Treiber installieren) aus.

Abb. 2

Installieren der Treiber

2

• Klicken Sie auf Next (Weiter), um den Treiber für den USB-Adapter zu

installieren. (Abb. 3)

• Lesen Sie die Lizenzvereinbarung. Wählen Sie Agree (Annehmen) aus, und

klicken Sie auf Next (Weiter), um mit der Installation fortzufahren. (Abb. 4)

• Es wird ein Fenster angezeigt, das Sie zum Anschließen des Wireless-

Adapters auffordert. Verbinden Sie das beiliegende Kabel mit dem

AirStation Wireless-USB-Adapter und einem USB-Anschluss des Computers.

(Abb. 5)

Abb. 3

15

DE

Installieren der Treiber

2

Abb. 4

Abb. 5

USB-Anschluss

Wireless-USB-Adapter

DE

16

Installieren der Treiber

2

• Wenn der „Assistent zum Suchen neuer Hardware“ gestartet wird, klicken

Sie auf Weiter, um den Assistenten auszuführen. (Abb. 6)

• Wenn das Dialogfeld „Digitale Signatur nicht gefunden“ geöffnet wird,

klicken Sie auf Ja. (Abb. 7)

• Nachdem der Wireless-USB-Adapter erfolgreich installiert wurde, klicken Sie

auf Fertig stellen. Starten Sie den Computer neu, wenn Sie dazu aufgefordert

werden. (Abb. 8)

Abb. 6

Abb. 7

17

DE

Der WLI-U2-SG54HG verfügt über eine integrierte, bidirektionale Antenne.

Um die bestmögliche Leistung zu erreichen, richten Sie die Antenne wie

unten gezeigt auf den Zugangspunkt (Access Point) aus.

Es können keine externen Antennen an den WLI-U2-SG54HG angeschlossen

werden.

Informationen zur Antenne

3

Abb. 8

Installieren der Treiber

2

DE

18

Installieren des Client Manager

4

Abb. 9

Mit der Client Manager-Software von Buffalo erhalten Sie einen Überblick

über alle unterstützten Funknetzwerke und können eine Verbindung

zu diesen herstellen. Außerdem ermöglicht sie die Installation und

Konfiguration in einem Schritt mittels AOSS.

Um Client Manager zu installieren, klicken Sie auf Install Client Manager

(Client Manager installieren) und folgen dem Assistenten durch den

Installationsprozess.

Klicken Sie auf Exit Setup (Setup beenden), um AirNavigator zu beenden.

Der Client Manager ist jetzt installiert und wird ausgeführt. Doppelklicken

Sie auf das zugehörige Symbol (die schwarze Antenne), um die Software zu

benutzen.

Abb. 10

Seite laden ...

Buffalo Technology AirStation WLI-U2-SG54HG Benutzerhandbuch

Dieses Handbuch ist auch geeignet für

Buffalo Technology AirStation WLI-U2-SG54HG Benutzerhandbuch

in anderen Sprachen

Verwandte Papiere

Sonstige Unterlagen