ZENEC Z-E3756 Naviceiver for Flat Ducato Benutzerhandbuch

Marke: ZENEC

Modell: Z-E3756 Naviceiver for Flat Ducato

Typ: Benutzerhandbuch

1 of 3 September 2022 / RevA

Z-E3756 Update Instructions MainSystem

Requirements

The update consists of a complete MainSystem software update, which must be run from USB data carrier. You will need:

> USB removable storage device (USB stick) with at least 2 GB storage capacity.

> A PC or notebook with Windows operating system.

Please note: Before you start, the USB stick must be formatted with FAT 32. (Right-click on USB memory device in Windows

Explorer. Select "Format" > FAT 32 > Start.

(!) The ZENEC Z-E3756 restarts several times during the software update and stays off, among other things, for a few seconds

(black screen for approx. 10 ~ 15 sec.) before the device restarts. Please do not operate or switch off the device during the update

process. After successful installation the tuner source will come up.

Installation of the MainSystem software update via USB:

The MainSystem software can be found at: www.zenec.com> Support> Software Updates> FIAT> Z-E3756

Link: http://www.zenec.com/support/software-updates/z-e3756/?lang=en

1. Download the Software Update “v1.8.6 "Z-E3756_FEU_v1.8.6.exe".

2. The software package is a self-unzipping executable. Start extraction with a double-click and select your USB stick as target

for the uncompressed ﬁ les.

3. You obtain two ﬁ les called „swupdate_6529B_20220815.zip” in the root directory of the USB stick

4. Connect the USB stick to the Z-E3756 USB-1 connection cable.

5. Go to the device menu:

Settings > System > Software Update and conﬁ rm by tapping on the green hook checkbox.

Tap on the green hook checkbox again, in the "Software Update?" pop-up window.

2 of 3 September 2022 / RevA

Z-E3756 Update Instructions MainSystem

5. The update process starts automatically now.

6. The update installs sequentially and the lower part of the display screen informs about the progress. The software installation

takes about 4~5 minutes.

Note: After successful installation, device reboot and shows the Tuner source.

Please do not operate or switch off the device during the restart process (duration approx. 3 minutes).

After restart, the tuner source OSD will show up.

Note: After the loading factory defaults, some personal settings must be set again (such as camera grid lines, audio

settings etc.).

7. Remove the USB stick.

8. Load factory

Note: After a successful update, the device menu language is in English.

You can set the language to your preference as follows. Go to the device menu:

Setup > System > Load Factory and conﬁ rm by tapping the green hook checkbox.

Tap on the green hook check box again upon "Load Factory?" prompt by the pop-up window.





5.DieSoftwareUpdateDateiwirdvomNaviceiverentpackt.DerUpdatevorgangstartetautomatisch.



6.DasUpdateinstalliertnunsequentiellundderuntereTeilbereichdesBildschirmsinformiert

überdenFortschritt.DieSoftwareInstallationdauertcirca4~5Minuten.

Hinweis:NacherfolgreicherInstallationwirddieTunerOberfläche(Tuner-Quelle)angezeigt.



7.EntfernenSiedenUSBStick.



8.Werkseinstellungenladen.

Hinweis:NacherfolgreichemUpdateistdieGerätemenü-SpracheinEnglisch.



BegebenSiesichimGerätemenüunter:

Setup>System>LoadFactoryundbestätigenSiediesdurchAntippendesgrünenHakens.

TippensieerneutaufdengrünenHakensbeiderAbfrage„LoadFactory?“imPopupFenster.





BittewährenddesNeustarts(Dauerca.3Minuten)dasGerätnichtbedienenoderausschalten.

NacherfolgreichemNeustartwirddieTunerOberfläche(Tuner-Quelle)angezeigt.

Hinweis:NachdemdieWerkseinstellungengeladenwurden,müsseneinigeEinstellungenerneuteingestellt

werden.(z.B.dieKamera-Einpark-HilfslinienundAudio-Einstellungen)



9.Spracheinstellung:

SiekönnennundieGerätespracheaufDeutschändern.

BegebenSiesichimGerätemenüunter:

Setup>Misc>tippenSieaufOSDLanguageundwählenGermaninderListeaus.BestätigenSiedurchAntippen

desgrünenHakens.

BestätigenSiedenWechselderSprachedurcherneutesAntippendesgrünenHakensimPopupFenster.



v1.8.4

Z-E3756 Update Instructions MainSystem

10. Ver sion control

After installing the software update a version check needs to be carried out. In the device menu:

Settings > System > Software Version Information.

Version: v1.8.6

If the version differs from the target version, install the update a new.

9. Language setting

After the update, the system language is set to English. You can now change the device language to your preference.

Go to the device menu:

Setup > Misc > tap on OSD Language and select your preferred language in the list. Conﬁ rm your language

selection by tapping on the green hook checkbox once more in the pop-up window.

3 of 3 September 2022 / RevA

v1.8.6

Improvements and Bugﬁ xes:

MAINSYSTEM

• Improved system performance

• Handbrake parking function logic change from previous parking cable usage to GPS-DR data usage

• Added new ZENEC CaraControl (Board Control) feature

Video: https://www.youtube.com/watch?v=V-TXYh79jM0

TUNER

• Bugﬁ x for FM Preset storage issue with local radio freq. that contain a comma

• Updated local Tuner Slideshow Database to v1.20

MEDIA PLAYER USB

• Bugﬁ x for USB crash in video playback when fast switching between MainMenu and back to USB

ZENEC Z-E3756 Naviceiver for Flat Ducato Benutzerhandbuch

Marke: ZENEC

Modell: Z-E3756 Naviceiver for Flat Ducato

Typ: Benutzerhandbuch

PDF Herunterladen

Bericht

in anderen Sprachen

English: ZENEC Z-E3756 Naviceiver for Flat Ducato User manual