Parkside PWSA 12-LI A1 Translation Of The Original Instructions

Marke: Parkside

Modell: PWSA 12-LI A1

Kategorie: Elektrowerkzeuge

Typ: Translation Of The Original Instructions

CORDLESS ANGLE GRINDER PWSA 12-LI A1

IAN 297696

AKKU-WINKELSCHLEIFER

Originalbetriebsanleitung

CORDLESS ANGLE GRINDER

Translation of the original instructions

ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟΣ

ΓΩΝΙΑΚΟΣ ΤΡΟΧΟΣ

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

297696_par_Akku-Winkelschleifer_cover_GB_IE_NI_CY.indd 2 26.01.18 14:11

GB / IE / NI / CY Translation of the original instructions Page

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα

DE / AT / CH Originalbetriebsanleitung Seite

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες της

συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

297696_par_Akku-Winkelschleifer_cover_GB_IE_NI_CY.indd 3 26.01.18 14:11

3 4

5 6

1314

GB IE NI CY

Content

Introduction .................................4

Intended purpose .........................4

General description ...................... 5

Extent of the delivery ........................5

Description of functions .....................5

Overview ........................................5

Technical data ..............................5

Notes on safety............................6

Symbols and icons .......................6

Symbols on the device: .....................6

Other symbols on the .......................7

cutting disc: ..................................7

Symbols on the battery: ............7

Symbols on the recharger: .................7

Symbols in the manual ......................8

General Safety Directions for

Power Tools ................................8

Special safety directions for

battery-operated tools ...............11

Safety instructions for all

applications ...............................12

Additional safety instructions .....14

RESIDUAL RISKS .........................15

Additional safety instructions

for all applications .....................15

Kickback and corresponding

precautions ................................15

Special safety instructions for

grinding and cutting ...................16

Other special safety instructions for

cutting grinding ......................... 17

Charging the battery .................. 17

Inserting/removing the battery .........18

Recharging the battery....................18

Used batteries ...............................18

Checking the battery charge level ....19

Assembly ...................................19

Set protective hood ...........................19

Installing/changing the cutting/grinding

disc ..............................................19

Wall mounted charger (optional) 20

Operation ..................................20

Introduction

Congratulations on the purchase of your

new device. With it, you have chosen a

high quality product.

During production, this equipment has

been checked for quality and subjected to

a nal inspection. The functionality of your

equipment is therefore guaranteed.

The operating instructions constitute part of

this product. They contain important infor-

mation on safety, use and disposal.

Before using the product, familiarise your-

self with all of the operating and safety

instructions. Use the product only as de-

scribed and for the applications specied.

Keep this manual safely and in the event

that the product is passed on, hand over

all documents to the third party.

Intended purpose

The cordless angle grinder is a tool for cut-

ting and grinding metal, stone and wood

materials, plastic, tiles and non-ferrous me-

tals without using water.

Switching on and off ......................21

Practical tips ..............................21

Cleaning and maintenance .........21

Cleaning .......................................22

Storage.........................................22

Disposal and protection of the envi-

ronment .....................................22

Guarantee ................................. 22

Repair Service ............................24

Service-Center ............................24

Importer .................................... 24

Troubleshooting .........................25

Replacement parts / Accessories 26

Translation of the original EC

declaration of conformity ........... 81

NI CYIEGB

The tool should not be used in any other

application (e.g. cutting/grinding with

coolant solutions, cutting/grinding harmful

substances such as asbestos).

The device is intended to be used by do-it-

yourselfers. It was not designed for heavy

commercial use. The tool is to be used by

adults. Children over the age of 16 may

not use the tool except under supervision.

The manufacturer is not liable for damages

caused by an improper use or incorrect

operation of this device.

General description

See the front fold-out page for

illustrations.

Extent of the delivery

Carefully unpack the appliance and check

that it is complete. Dispose of the pa-

ckaging material correctly.

- Device

- Cutting disc (preassembled)

- Battery-charger

- Battery

- Hex key (4 mm)

- Storage case

- Instruction Manual

Description of functions

The cordless angle grinder is suitable for

cutting and grinding metal, stone and

wood materials, plastic, tiles and non-

ferrous metals. There is a special disc for

each of the separate applications. Please

refer to the information from the disc manu-

facturer.

Please refer to the descriptions below for

information about the operating devices.

Overview

1 Protective hood

2 Cutting disc

3 Clamping screw

4 Spindle stop button

5 On/off switch

6 Battery Indicator (3LEDs)

7 Handgrip

8 Battery release button

9 Battery

10 Storage case

11 Hex key

12 Charger power supply cord

13 Green LED

14 Red LED

15 Charger

16 Mounting ange

17 Clamping ange

Technical data

Cordless angle grinder

...............................PWSA 12-Li A1

Rated input voltage ......................12 V

Idling speed (n) .....................19500 min

-1

Dimensions of cutting/grinding disc

...................................... Ø 76 x 10 mm

Bore hole ................................ Ø 10 mm

Maximum diameter

Cutting/grinding disc ............... Ø 76 mm

Thickness of cutting/grinding discs

......................................... max. 6.5 mm

Grinding spindle thread ..................... M5

Protection category...........................IPX0

Sound pressure level

) ...................64.7 dB(A); K

= 3 dB

Sound power level (L

)

measured .......... 75.7 dB(A); K

= 3 dB

Vibration (a

) ...... 2.37 m/s

; K= 1.5 m/s

GB IE NI CY

Battery (Li-Ion) .......... PAP 12-Li A1

Battery cells .....................................3

Model (Type) ........................ C18650P

Nominal voltage .......................12 V

Capacity ..................................2.0 Ah

Charging time ..........................ca. 1 h

Recharger ...................PLG 12-Li A1

Nominal consumption ................. 40 W

Uptake voltage/

Input ......................220-240 V~, 50 Hz

Voltage output/Output .....12 V

2.4 A

Protection class ............................

Protection category ...................... IPX0

The vibration values represent maximum valu-

es which have been determined with the sup-

plied blade. The actual vibration values may

vary depending on the used accessories.

The vibration values are still affected by the

handling for the user‘s.

Cutting disc PTS 76

(included):

Idling speed n

............. max.20300 min

-1

Disc speed ....................... max. 80 m/s*

Outer diameter ..................... Ø 76 mm

Bore hole ............................. Ø 10 mm

Thickness ...................................1 mm

The grinding disc must keep a rotational

speed of 80 m/s.

You can use all grinding tools mentioned in

these operating instructions.

Levels of noise and vibration were determi-

ned according to the norms and regulations

in the declaration of conformity.

The vibration emission value has been mea-

sured according to a standardised testing

method and may be used for comparison

with another electric tool.

The indicated vibration emission value may

also be used for an introductory assessment

of the exposure.

Warning:

The vibration emission value whilst

actually using the electrical tool may

vary from the given values indepen-

dently of the type and way in which

the electric tool is used.

Try to keep the exposure to vibra-

tions as low as possible. Examples

of measures to reduce vibration

exposure are the wearing of gloves

when using the tool and limiting the

working hours. For this purpose all

parts of the operating cycle have to

be considered (for example, times

when the electric tool is switched off

and times when it is switched on but

running without any load).

Notes on safety

Caution! When using

power tools, observe the

following basic safety

measures for the prevention

of electric shocks and the

risk of injury and re.

Please read all these instruc-

tions before using this elec-

tric tool and please keep

the safety instructions.

Symbols and icons

Symbols on the device:

Warning!

Read the manual!

NI CYIEGB

Store the battery in

charged condition

The battery requires an

ambient temperature of

+10 °C to + 40 °C

The battery should never

come into contact with wa-

ter.

Take batteries to an old

battery collection point

where they will be recy-

cled in an environmentally

friendly manner.

Symbols on the recharger:

Warning!

Before using for the rst

time, carefully read through

the user manual.

The recharger is for indoor

use only.

Miniature fuse

Protection class II (Double

insulation)

Electrical appliances must

not be disposed of with the

domestic waste.

LED display while

charging.

Wear ear protection

Wear eye protection

Wear breathing protection

Risk of cuts!

Wear cut-resistant gloves

Direction of rotation

Electrical machines do not

belong with domestic was-

Other symbols on the

cutting disc:

Do not use for side grin-

ding

Do not use for wet grin-

ding

Do not use defective discs

Wear safety shoes

Symbols on the battery:

Read the manual!

Do not dispose

of batteries in

household

waste, re or

water.

Do not subject the battery

to strong sunlight over long

periods and do not leave it

on a heater (max. 45 °C).

GB IE NI CY

Symbols in the manual

Warning symbols

with information on

damage and injury

prevention.

Hazard symbol with

information on the

prevention of perso-

nal injury caused by

electric shock.

Instruction symbols with

information on preventing

damage.

Help symbols with informa-

tion on improving tool han-

dling.

General Safety

Directions for Power

Tools

WARNING! READ ALL

SAFETY DIRECTIONS

AND INSTRUCTIONS.

Omissions in the compli-

ance with safety directions

and instructions can cause

electrical shock, re and/or

severe injuries.

Retain all safety directions

and instructions for future

use.

The term „power tool“ in the

warnings refers to your mains-

operated (corded) power tool or

battery-operated (cordless) power

tool).

Work area safety :

• Keep work area clean

and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power

tools in explosive atmos-

pheres, such as in the

presence of ammable

Iiquids, gases or dust. Po-

wer tools create sparks which

may ignite the dust or fumes.

• Keep children and by-

standers away while

operating a power tool.

Distractions can cause you to

lose control.

Electrical safety :

CAUTION! The following

states how to avoid acci-

dents and injuries due to

electric shock:

• Power tool plugs must

match the outlet. Ne-

ver modify the plug in

any way. Do not use

any adapter plugs with

earthed (grounded)

power tools. Unmodied

plugs and matching outlets

will reduce risk of electric

shock

• Avoid body contact with

earthed or grounded

surfaces, such as pipes,

radiators, ranges and

refrigerators. There is

an increased risk of electric

shock if your body is earthed

or grounded.

NI CYIEGB

• Do not expose power

tools to rain or wet con-

ditions. Water entering a

power tool will increase the

risk of electric shock.

• Do not abuse the cord.

Never use the cord for

carrying, pulling or

unplugging the power

tool. Keep cord away

from heat, oil, sharp

edges or moving parts.

Damaged or entangled cords

increase the risk of electric

shock.

• When operating a pow-

er tool outdoors, use an

extension cord suitable

for outdoor use. Use of a

cord suitable for outdoor use

reduces the risk of electric

shock.

• If operating a power

tool in a damp location

is unavoidable, use a

residual current device

(RCD) protected supply.

Use of an RCD reduces the

risk of electric shock. Use a

circuit breaker with a current

limit of 30 mA or less.

Personal safety:

CAUTION! The following

states how to avoid acci-

dents and injuries:

• Stay alert, watch what

you are doing and use

common sense when

operating a power tool.

Do not use a power tool

while you are tired or

under the inuence of

drugs, alcohol or medi-

cation. A moment of inatten-

tion white operating power

tools may result in serious

personal injury.

• Use personal protecti-

ve equipment. Always

wear eye protection. Pro-

tective equipment such as dust

mask, non-skid safety shoes,

hard hat, or hearing protec-

tion used for appropriate con-

ditions will reduce personal

injuries.

• Prevent unintentional st-

arting. Ensure the switch

is in the off-position

before connecting to

power source and/or

battery pack, picking

up or carrying the tool.

Carrying power tools with

your nger on the switch or

energising power tools that

have the switch on invites ac-

cidents.

• Remove any adjusting

key or wrench before

turning the power tool

on. A wrench or a key left

attached to a rotating part of

the power tool may result in

personal injury.

• Do not overreach. Keep

proper footing and ba-

lance at all times. This

enables better control of the

power tool in unexpected situ-

ations.

• Dress properly. Do not

wear loose clothing or

1 0

GB IE NI CY

jewellery. Keep your

hair, clothing and gloves

away from moving

parts. Loose clothes, jewelle-

ry or long hair can be caught

in moving parts.

• If devices are provided

for the connection of

dust extraction and coll-

ection facilities, ensure

these are connected and

properly used. Use of dust

collection can reduce dust-

related hazards.

Power tool use and care :

• Do not force the power

tool. Use the correct po-

wer tool for your appli-

cation. The correct power

tool will do the job better and

safer at the rate for which it

was designed.

• Do not use the power

tool if the switch does

not turn it on and off.

Any power tool that cannot

be controlled with the switch

is dangerous and must be re-

paired.

• Disconnect the plug from

the power source and/

or the battery pack from

the power tool befo-

re making any adjust

-ments, changing acces-

sories, or storing power

tools. Such preventive safety

measures reduce the risk of

starting the power tool acci-

dentaIly.

• Store idle power tools

out of the reach of child-

ren and do not allow

persons unfamiliar with

the power tool or these

instructions to operate

the power tool. Power

tools are dangerous in the

hands of untrained users.

• Maintain power tools.

Check for misalignment

or binding of moving

parts, breakage of parts

and any other condition

that may affect the po-

wer tool’s operation. If

damaged, have the po-

wer tool repaired before

use. Many accidents are

caused by poorly maintained

power tools.

• Keep cutting tools sharp

and clean. Properly main-

tained cutting tools with sharp

cutting edges are less Iikely

to bind and are easier to con-

trol.

• Use the power tool, ac-

cessories and tool bits

etc. in accordance with

these instructions, ta-

king into account the

working conditions and

the work to be perfor-

med. Use of the power tool

for operations different from

those intended could result in

a hazardous situation.

Service:

• Have your power tool

serviced by a qualied

repair person using only

identical replacement

1 1

NI CYIEGB

parts. This will ensure that

the safety of the power tool is

maintained.

SPECIAL SAFETY

DIRECTIONS FOR

BATTERY-OPERATED

TOOLS

• Ensure that the device

is switched off before

inserting the battery.

Inserting a battery into a

power tool that is switched

on may result in accidents.

• Recharge the batteries

indoors only because

the battery charger is

designed for indoor use

only.

• To reduce the electric

shock hazard, unplug

the battery charger

from the mains before

cleaning the charger.

• Do not subject the bat-

tery to strong sunlight

over long periods and

do not leave it on a

heater. Heat damages the

battery and there is a risk of

explosion.

• Allow a hot battery to

cool before charging.

• Do not open up the bat-

tery and avoid mechani-

cal damage to the bat-

tery. Risk of short circuit and

fumes may be emitted that

irritate the respiratory tract. En-

sure fresh air and seek medi-

cal assistance in the event of

discomfort.

• Do not use non-re-

chargeable batteries!

Correct handling of the

battery charger

• This appliance can be used

by children aged from 8

years and above and per-

sons with reduced physical,

sensory or mental capabilities

or lack of experience and

knowledge if they have been

given supervision or instruc-

tion concerning use of the

appliance in a safe way

and understand the hazards

involved. Children shall not

play with the appliance.

Cleaning and user mainte-

nance shall not be made by

children without supervision.

• To charge the battery,

use only the charger

supplied. Risk of re and

explosion. This ensures that

the safety of the device is

maintained.

• Before each use, check

the charger, cable and

plug and have them re-

paired by qualied pro-

fessionals and only with

original parts. Do not use

a defective charger and do

not open it up yourself. This

ensures that the safety of the

device is maintained.

• Connect the charger

only to a socket with an

earth. Ensure that the

mains voltage matches

the specications on the

1 2

GB IE NI CY

charger rating plate. Risk

of electric shock.

• Keep the charger clean

and away from wet

and rain. Do not use

the charger outdoors.

Dirt and the entry of water

increase the risk of electric

shock.

• Operate the charger

only with the appropri-

ate original batteries.

Charging other batteries may

result in injuries and risk of

re.

• Avoid mechanical dam-

age to the charger. This

can result in internal short

circuits.

• Do not operate the

charger on a combusti-

ble surface (e.g. paper,

textiles). Risk of re due to

heating during charging.

• If the connection ca-

ble of this appliance is

damaged, it must be re-

placed by the manufac-

turer or their customer

service or by a similarly

qualied person in or-

der to avoid hazards.

• The battery of the appliance

is not fully charged at the

time of delivery. It therefore

needs to be fully recharged

before you use it for the rst

time. Slot the battery into the

base and plug the battery

charger into a mains outlet..

• Disconnect the mains plug

when the battery is fully

charged and disconnect the

battery from the charger.

Do not allow your battery to

charge continuously. This can

damage the battery cells. Do

not briey charge the bat-

tery several time in a row.

Recharge the battery when

you notice that the appliance

is becoming slower.

• Do not use the charger to

charge non-rechargeable bat-

teries.

Safety instructions for

all applications

Common safety

instructions for grinding

and cutting:

• This electric tool is to be

used as a grinder and

cutting grinder. Follow

all safety instructions, di-

rectives, illustrations and

facts which you receive

with the device. If you do

not follow these instructions,

an electrical shock, re and/

or serious injury may occur.

• This electric tool is not

suitable for sanding,

wire brushing and po-

lishing. Using the electric

tool in ways for which it is not

intended may cause hazards

and injuries.

• Do not use any ac-

cessories that are not

specically intended

and recommended for

this electric tool by the

manufacturer. Simply be-

cause an accessory can be

1 3

NI CYIEGB

attached to your electric tool

does not guarantee safe ope-

ration.

• The allowable rotation

speed of the attachment

tools must be at least as

high as the highest rota-

tion speed indicated on

the electric tool. Accesso-

ries that run faster than the

allowable speed can break

and y apart.

• The outside diameter

and thickness of the at-

tachment tool must cor-

respond to the dimen-

sions indicated for your

electric tool. Attachment

tools which are wrongly di-

mensioned cannot be sufci-

ently shielded or controlled.

• Attachment tools with

threaded attachment

must t the threading

of the grinding spindle

exactly. For attachment

tools which are moun-

ted through a ange,

the diameter of the hole

in the attachment tool

must t the mounting

diameter of the ange.

Attachment tools which can-

not be precisely attached to

the electric tool turn unevenly,

vibrate very strongly and can

ultimately lead to a loss of

control.

• Never use damaged at-

tachment tools. Check

attachment tools such as

grinding discs for chip-

ping or cracks, grinding

plates for cracks, wear

or strong abrasion be-

fore using them. If the

electric tool or the at-

tachment tool falls off,

check whether it is da-

maged or use an unda-

maged attachment tool.

If you have checked the

attachment tool and at-

tached it, keep yourself

and any nearby persons

beyond the level of the

rotating attachment tool

and allow the device to

run for 1 minute at the

highest rotational speed.

Damaged tools usually break

during this test period.

• Wear personal safety

equipment. Depending

on the application, use

full face shields, eye

protection or safety

goggles. In so far as it is

appropriate, wear dust

masks, ear protection,

gloves or special aprons

which keep small grin-

ding and material par-

ticles away from you.

Eyes should be protected

from the foreign matter which

can be caused to y during

the various applications. Dust

or breathing masks should

lter the dust that is created

during operation. If you are

exposed to loud noise for

a long time, you may suffer

hearing loss.

• Ensure that other people

are at a safe distance

to your working

area.

Anyone who enters the

1 4

GB IE NI CY

wor

king area should

wear personal protective

equipment. Broken bits from

the piece being worked or

broken attach

ment tools can y

away and cause injuries

even

beyond the direct working

area.

• Keep the cord away

from the rotating attach-

ment tool. If you lose con-

trol of the device, the power

cord can become separated

or caught and your hand or

arm may be pulled into the

rotating attachment tool.

• Never put the electric

tool down before the at-

tachment tool has come

to a full stop. The rotating

attachment tool can come into

contact with the surface upon

which it is set, whereby you

could lose control of the elec-

tric tool.

• Never allow the elec-

tric tool to run while

you are carrying it. Your

clothing may accidentally

come into contact with the

rotating attachment tool and

get caught and the attach-

ment tool could drill into your

body.

• Clean the ventilation

slots of your electric tool

routinely. The motor air

pulls dust into the housing

and, should too much metallic

dust collect, could cause elec-

trical hazards.

• Never use the electric

tool near ammable

material. Sparks could igni-

te this material.

• Do not use attachment

tools which require li-

quid coolant. Using water

or another liquid coolant

could lead to electrical shock.

Additional safety

instructions

• Only use grinding discs whe-

re the indicated rotational

speed is at least as high as

what has been specied on

the name plate of the device.

• Carry out a visual inspection

of the grinding disc before use.

Do not use any dama

ged or

deformed grinding discs. Re-

place

any damaged or worn

grinding discs.

• Make sure that the sparks

produced by grinding do not

present a danger, e.g. reach

people or ignite ammable

substances.

•

Always wear safety goggles,

safety gloves,

respiratory pro-

tection and ear protection

when grinding, brushing and

cutting.

• Never keep the ngers bet-

ween the grinding disc and

spark protection or in close

proximity to the protective

hoods. There is a risk of crus-

hing.

• The rotating parts of the de-

vice cannot be covered due

to functional reasons. There-

fore, proceed cautiously and

hold the workpiece rmly in

order to avoid slipping which

1 5

NI CYIEGB

could cause your hands to

come into contact with the

grinding disc.

• The workpiece gets hot du-

ring grinding. Do not touch

the machined area, allow

it to cool down. There is a

risk of burning. Do not use

coolants or the like.

• If you are tired or have con-

sumed alcohol or tablets, do

not work with the device. Al-

ways have a break on time..

• Turn off the device and remo-

ve the battery from the device

before servicing the device.

RESIDUAL RISKS

Even if properly operating and

handling this electric tool, some

residual risks will remain. Due

to its construction and build, this

electric tool may present the fol-

lowing hazards:

a) Lung damage if suitable respi-

ratory protection is not worn.

b) Hearing damage if suitable

ear protection is not worn.

c) Damage to health due to

- touching the area of the

grinding tool which is not

covered;

- ejection of parts of workpi-

eces or damaged grinding

discs.

d) Health injuries which result

from swinging hand and arm,

in the event that the device is

used over a longer period of

time or is not used and main-

tained properly.

Warning! During opera-

tion, this electric tool gene-

rates an electromagnetic

eld which, under certain

circumstances, may impair

the functionality of active or

passive medical implants.

To reduce the risk of serious

or lethal injuries, we re-

commend that persons with

medical implants consult

their doctor and the ma-

nufacturer of their medical

implant before operating

the machine.

Additional safety

instructions for all

applications

Kickback and

corresponding precautions

Kickback is the sudden reaction

from a chopping or blocked

grinder attachment such as a

grinding disc, grinding plate,

wire brush etc. Chopping or

blocking leads to sudden stop-

ping of the rotating attachment.

This causes an uncontrolled elec-

tric tool to accelerate in a direc-

tion counter to the rotational di-

rection of the attachment tool. If,

for example, a grinding disc cuts

into the workpiece or blocks it,

the edge of the grinding disc that

digs into the workpiece can get

caught and, through that, break

off the grinding disc or cause a

kickback. The grinding disc then

moves towards or away from

the operator, depending on the

direction of rotation of the disc

1 6

GB IE NI CY

at the blocked spot. Here, the

grinding discs can also break. A

kickback is caused by wrongly

or incorrectly operating the elec-

tric tool. It can be avoided by

suitable cautionary measures,

such as described below.

a) Hold the electric tool very rm-

ly and bring your body and

your arm into a position in

which you can resist the kick-

back force. Always use the

supplemental handle if availa-

ble to give you the best control

over kickback force or reac-

tion time during acceleration.

The operator can master the

kickback and reaction force

through suitable precautions.

b) Never bring your hands near

a rotating attachment tool.

The attachment tool can run

over your hand in the kick-

back.

c) Keep your body away from

the area in which the electric

tool would move during a

kickback. The kickback drives

the electric tool in the counter-

direction to the rotation of the

grinding disc at the blocked

spot.

d) Work particularly cautiously

in corner areas or where the-

re are sharp corners etc. Pre-

vent the attachment tools from

recoiling from the workpiece

and jamming. The rotating

attachment tool tends to jam

when near corners, sharp

edges or when it recoils from

such. This causes a loss of

control or kickback.

e) Do not use chain or toothed

saw blades. Such attachment

tools frequently cause a kick-

back or loss of control over

the electric tool.

Special safety instructions

for grinding and cutting

a) Use only grinders which have

been approved for your elec-

tric tool and the protective

hood intended for these grin-

ders. Grinders which are not

intended for the electric tool

may not be sufciently shiel-

ded and are unsafe.

b) Depressed Center grinding

wheels must be pre-assem-

bled so that their surface not

above the level of the edge

of the guard stands out. An

improperly mounted grinding

wheel, which extends beyond

the level of the edge of the

guard, not sufciently shiel-

ded.

c) The protective hood must

be securely attached to the

electric tool and adjusted

so that the greatest level of

safety is reached, i.e., the

smallest possible amount of

the grinder is exposed to the

operator. The protective hood

should protect the operator

from broken bits and acciden-

tal contact with the grinder.

d) Grinders may only be used

for the recommended attach-

ment options. For example:

Never grind with the side sur-

face of a cutting disc. Cutting

1 7

NI CYIEGB

discs are for cutting material

using the edge of the disc.

Pushing sideways on these

grinders can break them.

e) Always use undamaged

clamping anges of the cor-

rect size and shape for the

grinding disc you selected.

Suitable anges support the

grinding disc and thus reduce

the danger of the grinding

disc breaking. Flanges for

cutting discs can be distingu-

ished from anges for other

grinding discs.

f) Do not use worn grinding

discs for larger electric tools.

Grinding discs for larger elec-

tric tools are not set up for

the higher rotation speeds of

smaller electric tools and can

break.

Other special safety

instructions for cutting

grinding

a) Avoid blocking the cutting

disc or pressing down too

hard. Do not make any exces-

sively deep cuts. Overloading

the cutting disc increases

wear and its tendency to tilt

or block and, with that, to

kickback or break the grin-

der.

b) Avoid the area in front of and

behind the rotating cutting

disc. When you move the cut-

ting disc by itself in the work-

piece, in the event that the

electric tool kicks back with

the rotating disc, it can spin

directly towards you.

c) If the cutting disc jams, or you

interrupt your work, switch

the device off and hold it until

the disc has come to a full

stop. Never try to pull the cut-

ting disc out of the cut while

it is still running, because it

can kick back. Identify and

correct the cause of the jam-

ming.

d) Do not switch the electric tool

on again as long as it is in

the workpiece. Allow the cut-

ting disc to rst reach its full

rotational speed before you

carefully resume with the cut-

ting. Otherwise, the disc may

catch, spring away from the

workpiece or cause a kick-

back.

e) Support plates or workpieces

to reduce the risk of kickback

from a jammed cutting disc.

Large workpieces may bend

under their own weight. The

workpiece must be supported

on both sides of the disc,

near the cutting disc as well

as also at the edge.

f) Be particularly careful for po-

cket cuts in existing walls or

other areas where you cannot

see what is there. The cutting

disc may cause a kickback

when it cuts into gas or water

lines, electrical lines or other

hidden objects.

Charging the battery

Do not expose the battery to

extreme conditions such as

1 8

GB IE NI CY

heat or impact. Risk of injury

from escaping electrolytic so-

lution! After eye/skin contact,

rinse the affected areas with

water or a neutraliser and

consult a doctor.

Charge the battery in a dry

room only.

Prior to attaching the charger,

check that the battery‘s outer

surface is clean and dry.

There is a risk of injury due

to electric shock.

Only use the original charger from

the package to charge the battery.

Make sure that the power supply

voltage matches the voltage rating

indicated on the device‘s type plate.

• Charge the battery before the rst time

of use.

• Recharge the battery when you notice

that the appliance is becoming slower.

• If a fully recharged battery lasts for

considerably shorter operating times,

the battery is used up and needs to

be replaced. Only use an OEM spare

battery available from our Customer

Service.

Inserting/removing the

battery

1. To insert the battery (9), place

it on the guide track and push it

back into the appliance. It will

audibly snap in.

2. To remove the battery (9) from

the appliance, press the release

buttons (8) on the battery and

pull out the battery.

Recharging the battery

1. Remove the battery (9) from the

appliance i necessary.

2. Insert the battery (9) in the charg-

ing compartment of the battery

charger (15).

3. Plug the battery charger (15) into

a mains outlet.

4. When the battery is fully re-

charged unplug the battery

charger (15) from the mains.

5. Pull the battery (9)out of the bat-

tery charger (15).

Overview of the LED indicators on

the charger (15):

Green LED (13) lights up

without battery inserted:

Charger ready.

Green LED (13) lights up:

Battery such alleged

charged.

Red LED (14) lights up:

Battery charging.

Used batteries

• If a fully recharged battery lasts for

considerably shorter operating times,

the battery is used up and needs to be

replaced. Only use an OEM battery

pack replacement available from our

Customer Service.

• Always take heed of the applicable

safety instructions as well as the envi-

ronmental protection regulations and

information (see “Cleaning and Main-

tenance”).

1 9

NI CYIEGB

Checking the battery charge

level

The battery’s ( 9) charge level is indi-

cated by the charge state indicator (

6).

The LEDs indicate the battery’s charge

level, when the device is in operation.

Press and hold the power button (

5).

red-yellow-green => Battery fully charged

red and yellow => Battery half charged

red => Battery needs

to be charged

Assembly

Caution! Risk of injury!

- Ensure that you have sufcient

space in which to work, and that

you do not endanger other people.

Set protective hood

Adjust the protective hood such that any

sparks or detached parts cannot hit either

the user or any bystanders.

The protective hood must also be positi-

oned such that the sparks cannot ignite

combustible parts, including those in the

surroundings.

The device must only be

operated with the protective

hood mounted.

1. Remove the battery (9). Press the

battery release buttons (8) and

pull the battery (9) out of the

tool.

2. Turn the protective hood (1) into

the working position. The closed

side of the protective hood must

always face the operator.

Installing/changing the

cutting/grinding disc

Before initial operation,

check the tightness of the

clamping screw (3).

1. Press the spindle retaining tab

(4) and keep it pressed.

2. Loosen the clamping screw (3)

with the Allen key (11). You can

now release the spindle retaining

tab (4).

3. Position the desired cutting/

grinding disc (2) on the moun-

ting ange (

16). The label on

the cutting/grinding disc should

always face the tool.

4. Reposition the clamping ange

(17). The side of the clamping

ange (

17). The side of the

clamping ange (

17) with re-

cess generally points to the attach-

ment tool and thus to the cutting/

grinding disc (2).

5. Press the spindle retaining tab (4)

and tighten the clamping screw (3)

using the Allen key (11). You can

now release the spindle retaining

tab (4).

If the direction of rotation is marked

on your cutting/grinding disc, make

sure that it matches the direction of

rotation mark on the tool.

2 0

GB IE NI CY

Wall mounted charger

(optional)

You can also mount the charger (15) on

the wall.

• Using dowels, place two screws

54 mm apart at the desired posi-

tion of a wall.

• The screw head can have a dia-

meter of 6 - 10 mm

• Leave the screw heads protru-

ding at a distance of approx. 10

mm from the wall.

• With the openings of the wall

bracket, you can attach the char-

ger (15) to the two screws and

pull the charger down until it

stops.

Operation

Caution! Risk of injury!

- Only use grinding tools which

bear information about the

manufacturer, type of binding,

dimension and permitted number

of revolutions.

- Only use grinding discs where

the printed rotational speed is at

least as high as what has been

specied on the name plate of

the device.

- Do not use any broken, cracked,

or otherwise damaged grinding

discs.

- Never operate the device wit-

hout protective equipment.

- Support the plates or workpieces

in order to reduce the risk of

kickback from a jammed cutting

disc. Large workpieces may

bend under their own weight.

The workpiece must be suppor-

ted on both sides of the disc, not

only near the cutting disc, but

also at the edge.

Keep your hands away

from the disc when the de-

vice is in operation. Risk of

injury.

Information on replacement:

• Never operate the device without

protective equipment.

• Ensure that the rotation speed sta-

ted on the grinding disc (

11) is

the same or higher than the nomi-

nal rotation speed of the device.

•

Ensure that the grinding disc dimen-

sions match those of the device.

• Only use awless grinding discs

(ringing test: when you strike the

grinding disc with a plastic ham-

mer, it results in a clear sound).

• Never re-drill a locating hole which

is too small to make it larger.

• Never use separate bushings or

adapters in order to make grin-

ding discs with a hole that is too

large t the device.

• Do not use any saw blades.

• To clamp the grinding tools

only use the clamping ange

provided. The pads between

the clamping ange and the

grinding tools must be made of

elastic materials e.g., rubber,

soft cardboard etc.

Switch off the tool and remove the

battery before you service the tool.

Wear protective gloves when chan-

ging the cutting/grinding discs in

order to avoid injuries from cuts.

Seite laden ...

Parkside PWSA 12-LI A1 Translation Of The Original Instructions

Marke: Parkside

Modell: PWSA 12-LI A1

Kategorie: Elektrowerkzeuge

Typ: Translation Of The Original Instructions

PDF Herunterladen

Bericht

in anderen Sprachen

English: Parkside PWSA 12-LI A1

Parkside PWSA 12-LI A1 Translation Of The Original Instructions

Parkside PWSA 12-LI A1 Translation Of The Original Instructions

in anderen Sprachen

Verwandte Papiere