IKEA RENLIGWM Benutzerhandbuch

Kategorie
Waschmaschinen
Typ
Benutzerhandbuch
RENLIG
IWM60
GB
DE
ENGLISH 4
DEUTSCH 27
Contents
Safety information 4
Safety instructions 5
Product description 7
Control panel 8
First use 10
Daily use 10
Helpful hints and tips 13
Washing programmes 14
Consumption values 16
Care and cleaning 17
Troubleshooting 20
Technical information 22
Environment concerns 23
IKEA GUARANTEE 24
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible if
an incorrect installation and use causes injuries and damages.
Always keep the instructions with the appliance for future refer-
ence.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or permanent disability.
Do not let persons, children included, with reduced physical
sensory, reduced mental functions or lack of experience and
knowledge use the appliance. They must have supervision or
instruction for the operation of the appliance by a person
who is responsible for their safety.
Do not let children play with the appliance.
Keep all packaging away from children.
Keep all detergents away from children.
Keep children and pets away from the appliance door when
it is open.
If the appliance has a child safety device, we recommend
you activate it.
General Safety
Before maintenance, deactivate the appliance and discon-
nect the mains plug from the mains socket.
Do not change the specification of this appliance.
ENGLISH 4
Obey the maximum load volume of 6 kg (refer to the “Pro-
gramme chart” chapter).
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
The operating water pressure (minimum and maximum) must
be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa)
The ventilation openings in the base (if applicable) must not
be obstructed by a carpet.
The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.
Safety instructions
Installation
Remove all the packaging and the transit
bolts.
Keep the transit bolts. When you move
the appliance again you must block the
drum.
Do not install or use a damaged appli-
ance.
Do not install or use the appliance where
the temperature is less than 0 °C or
where it is exposed to the weather.
Obey the installation instruction supplied
with the appliance.
Make sure that the floor where you install
the appliance is flat, stable, heat resistant
and clean.
Do not install the appliance where the
appliance door can not be fully opened.
•Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
Make sure that there is air circulation be-
tween the appliance and the floor.
Adjust the feet to have the necessary
space between the appliance and the
carpet.
Electrical connection
Warning! Risk of fire and electrical
shock.
The appliance must be earthed.
Make sure that the electrical information
on the rating plate agrees with the power
supply. If not, contact an electrician.
Always use a correctly installed shock-
proof socket.
Do not use multi-plug adapters and ex-
tension cables.
Make sure not to cause damage to the
mains plug and to the mains cable. Con-
tact the Service or an electrician to
change a damaged mains cable.
Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
Do not pull the mains cable to disconnect
the appliance. Always pull the mains
plug.
Do not touch the mains cable or the
mains plug with wet hands.
This appliance complies with the E.E.C.
Directives.
ENGLISH 5
Water connection
Make sure not to cause damage to the
water hoses.
The appliance is to be connected to the
water mains using the new supplied
hose-sets. Old hose sets must not be
reused.
Before you connect the appliance to new
pipes or pipes not used for a long time,
let the water flow until it is clean.
The first time you use the appliance,
make sure that there is no leakage.
Use
Warning! Risk of injury, electrical
shock, fire, burns or damage to the
appliance.
Use this appliance in a household envi-
ronment.
Obey the safety instructions on the deter-
gent packaging.
Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
Do not touch the glass of the door while a
programme operates. The glass can be
hot.
Make sure that you remove all metal ob-
jects from the laundry.
Do not put a container to collect possible
water leakage under the appliance. Con-
tact the Service to ensure which accesso-
ries can be used.
Care and Cleaning
Warning! Risk of injury or damage to
the appliance.
Do not use water spray and steam to
clean the appliance.
Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do not
use abrasive products, abrasive cleaning
pads, solvents or metal objects.
Disposal
Warning! Risk of injury or suffocation.
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
Remove the door catch to prevent chil-
dren and pets to get closed in the appli-
ance.
Service
Contact the Service to repair the appli-
ance. We recommend only the use of
original spare parts.
ENGLISH 6
Product description
1
2
3
4
5
6
1
Detergent dispenser drawer
2
Control panel
3
Door opening handle
4
Rating Plate
5
Drain pump
6
Adjustable feet
Detergent dispenser drawer
Compartment for detergent used for
prewash and soak phase or for stain re-
mover used during the stain action phase (if
available). The prewash and soak deter-
gent is added at the beginning of the wash
programme. The stain remover is added
during the stain action phase.
Compartment for powder or liquid de-
tergent used for main wash. If using liquid
detergent pour it just before starting the
programme.
Compartment for liquid additives (fabric
softener, starch).
Follow the product manufacturer’s rec-
ommendations on quantities to use
and do not ever exceed the «MAX» mark in
the detergent dispenser drawer. Any fabric
softener or starching additives must be
poured into the compartment before start-
ing the wash programme.
ENGLISH 7
Door safety button
This appliance incorporates a special fea-
ture to prevent children and pets becom-
ing trapped inside the drum.
To activate this de-
vice, rotate the but-
ton clockwise (with-
out pressing it) in-
side the door until
the groove is hori-
zontal. If necessary
use a coin.
To disable this de-
vice and restore the
possibility of closing
the door, rotate the
button anticlockwise
until the groove is
vertical.
Control panel
Below is a picture of the control panel. It shows the programme selector dial as well as
the buttons and the indicator lights. These are presented by relevant numbers on the
following pages.
3h
12 0 0
900
700
500
6h 9h
30°
40°
60°
90°
40°
30°
40°
60°
30°
30°
40°
1
4567
2 3
1
Programme selector dial
2
Delay Start button
3
Programme Indicator lights
4
Start/Pause button
5
Extra Rinse button
6
Multi-Functions button
7
Spin reduction button
ENGLISH 8
Programme selector dial It allows you to switch the appliance On/Off and/or to select
a programme.
Delay Start button This button allows you to delay the start of the programme
by 3, 6 or 9 hours.
Programme Indicator lights
3.1
3.2
3.3
When selecting a washing programme both lights 3.1 and
3.2 illuminate.
When you have pressed the button 4 the only light corre-
sponding to the running phase stays on.
The appliance starts working and the door is locked.
The light 3.3 illuminates at the end of the washing cycle. Af-
ter a few minutes the door can be opened.
If the draining programme is selected any light will illu-
minate.
Start/Pause button This button allows you to start or to interrupt the selected
washing programme.
Spin reduction button By pressing this button you can change the spin speed of the
selected programme.
Rinse Hold
By selecting this option the water of the last rinse is not
emptied out to prevent the fabrics from creasing. Before
opening the door it will be necessary to empty out the wa-
ter. To empty out the water, please read the paragraph
«At the end of the programme».
Multi-Functions button: By pressing this button, you can select only one of the op-
tions. The relevant light will light up.
Prewash
By selecting this option the appliance performs a prewash
cycle before the main wash phase. The washing time will
be prolonged. This option is recommended for heavily
soiled laundry.
Super Quick
By selecting this option the appliance performs a very
short cycle for slightly soiled items that have been worn for
a short time.
Extra Rinse button This appliance is designed for saving energy. If it necessary
to rinse the laundry using an extra quantity of water (extra
rinse), select this option. Some additional rinses will be per-
formed. This option is recommended for people who are al-
lergic to detergents, and in areas where the water is very
soft.
ENGLISH 9
Table of symbols
= On/Off - Reset
= Drain
= Cottons = Spin
= Cottons economy at 60° C = Rinse Hold
= Cottons economy at 40° C = Prewash
= Cold wash = Super Quick
= Synthetics = Extra Rinse
= Easy Iron
= Delay Start
= Delicates = Main Wash
= Wool = End Cycle
= Handwash = Start/Pause
= Rinses
First use
1. Ensure that the electrical and water
connections comply with the installation
instructions.
2. Remove any material from the drum.
3. Pour 2 liters of water into the main
wash compartment
of the detergent
drawer in order to activate the ECO
valve.
Select a cotton cycle at the highest tem-
perature without any laundry in the ap-
pliance, to remove any manufacturing
residue from the drum and tub.
Pour 1/2 a measure of detergent into
the main wash compartment and start
the appliance.
Daily use
Open the door
Open the door by carefully pulling the door
handle outwards.
Load the laundry
Place the laundry in
the drum, one item
at a time, shaking
them out as much
as possible.
By pushing the
porthole frame,
close firmly the
door.
ENGLISH 10
Measure out detergent and fabric
softener
1
Pour the detergent
into the main wash
compartment
or
in the appropriate
compartment if the
selected pro-
gramme/option it
requires (see more
details in "Deter-
gent dispenser
drawer").
To pour the right
quantity of the de-
tergent, see more
details in "Degrees
of water hardness".
1
Pour fabric softener
into the compart-
ment marked
(must not exceed
the «MAX» mark in
the drawer).
Close the drawer gently
Select the required programme by turning
the programme selector dial (1)
The appliance is now switched on. The indi-
cator light of button 4 starts to blink.
At the end of the programme the selector
dial must be turned to position O, to switch
the appliance off.
For the description of each wash cycle,
the compatibility among the washing
programmes and the options, consult the
chapter «Washing Programmes».
Caution! If you turn the programme
selector dial to another programme
when the appliance is working, the red
indicator light of button 4 will blink 3 times
to indicate a wrong selection. The
appliance will not perform the new selected
programme.
Reduce the spin speed by pressing button
7
By selecting a programme, the appliance
proposes automatically the maximum spin
speed provided for that programme.
Press button 7 repeatedly to change the
spin speed, if you want your laundry to be
spun at a different speed. The relevant indi-
cator light illuminates.
Select the available options by pressing
buttons 7, 6 and 5
Depending on the programme, different
functions can be combined. These must be
selected after choosing the desired pro-
gramme and before starting the pro-
gramme.
When these buttons are pressed, the corre-
sponding indicator lights illuminate. When
they are pressed again, the indicator lights
go out. If an incorrect option is selected, the
integrated red indicator light of the button 4
flashes for 3 times.
For the compatibility among the wash-
ing programmes and the options see
chapter «Washing Programmes».
Select the Delay Start by pressing button
2
Before you start the programme, if you wish
to delay the start, press the button 2 re-
peatedly, to select the desired delay. The
relevant light illuminates.
You must select this option after you have
set the programme and before you start the
programme.
You can cancel or modify the delay time at
any moment, before you press button 4.
ENGLISH 11
Selecting the delayed start:
1. Select the programme and the required
options.
2. Select the delay start by pressing the
button 2.
3. Press button 4:
the appliance starts its countdown.
The programme will start after the
selected delay has expired.
Cancelling the delayed start after having
started the programme:
1. Set the washing appliance to PAUSE by
pressing button 4.
2. Press button 2 once, the light relevant
to the selected delay goes off
3. Press button 4 again to start the pro-
gramme.
The Delay Start can not be selected with
DRAIN programme.
Important! The selected delay can be
changed only after selecting the washing
programme again.
The door will be locked throughout the de-
lay time. If you need to open the door, you
must set the appliance to PAUSE (by press-
ing the button 4) and then wait a few mi-
nutes. After you have closed the door, press
the button 4 again.
Start the programme by pressing button 4
To start the selected programme, press the
button 4, the corresponding green indicator
light stops blinking. The indicator light cor-
responding to the running phase illumi-
nates. The appliance starts operating and
the door is locked.
To interrupt a programme which is running,
press the button 4: the corresponding green
indicator light starts blinking.
To restart the programme from the point at
which it was interrupted, press the button 4
again. If you have chosen a delayed start,
the appliance will begin the countdown.
If an incorrect option is selected, the red in-
dicator light of the button 4 blinks 3 times.
Altering an option or a running
programme
It is possible to change some options before
the programme carries them out.
Before you make any change, you must
PAUSE the appliance by pressing the button
4.
Changing a running programme is possible
only by resetting it. Turn the programme se-
lector dial to O and then to the new pro-
gramme position. Start the new programme
by pressing the button 4 again. The wash-
ing water in the tub will be not emptied out.
Interrupting a programme
Press the button 4 to interrupt a programme
which is running, the corresponding green
indicator light starts blinking.
Press the button again to restart the pro-
gramme.
Cancelling a programme
Turn the selector dial to O to cancel a pro-
gramme which is running.
You can select now a new programme.
Opening the door
After the programme has started the door is
locked. If, for any reason, you need to open
it, set firstly the appliance to PAUSE by
pressing the button 4. After a few minutes it
will be possible to open the door.
If the door remains locked, this means that
the appliance is already heating or that the
water level is too high. In any case, do not
try to force the door!
If you cannot open the door but you need
to open it you have to switch the appliance
off by turning the selector dial to O. After a
few minutes the door can be opened (pay
attention to the water level and tempera-
ture!).
After closing the door, it is necessary to se-
lect the programme and options again and
to press button 4.
At the end of the programme
The appliance stops automatically. The in-
dicator light of button 4 and the indicator
light corresponding to the just finished
washing phase goes off. The light 3.3 illumi-
nates. After a few minutes the door can be
opened.
ENGLISH 12
If a programme or an option that ends with
water left in the tub has been selected, the
light 3.3 illuminates but the door remains
locked to indicate that the water must be
emptied out before opening the door.
During this time the drum continues to turn
at regular intervals until water draining.
Follow the below instructions to empty out
the water:
1. Turn the programme selector dial to O.
2. Select the draining or spinning pro-
gramme.
3. Reduce the spin speed if needed, by
pressing the button 7.
4. Press button 4.
At the end of the programme, the door can
be now opened. Turn the programme selec-
tor dial to O to switch the appliance off.
Remove the laundry from the drum and
carefully check that the drum is empty. If
you do not intend to carry out another
wash, close the water tap. Leave the door
open to prevent any mildew and unpleas-
ant smells.
Stand by: once the programme has
finished the energy saving system is
enabled with the pilot lights switched on. By
pressing any button the appliance will come
out of the energy saving status.
Helpful hints and tips
Sorting out the laundry
Follow the wash code symbols on each gar-
ment label and the manufacturer’s washing
instructions. Sort the laundry as follows:
whites, coloureds, synthetics, delicates,
woollens.
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisa-
ble to treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
stain remover product then rub in the soap
and water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth
and dab the stain; treat several times.
Dried grease stains: moisten with turpen-
tine, lay the garment on a soft surface and
dab the stain with the fingertips and a cot-
ton cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since
the cellulose structure will already have
been damaged and the fabric tends to
hole.
Mould stains: treat with bleach, rinse well
(white cottons and fast coloureds only).
Grass: soap lightly and treat with bleach
(white cottons and fast coloureds only).
Ball point pen and glue: moisten with ace-
tone
1)
, lay the garment on a soft cloth and
dab the stain.
Lipstick: moisten with acetone as above,
then treat stains with methylated spirits.
Treat any residual marks with bleach.
Red wine: soak in water and detergent,
rinse and treat with acetic or citric acid,
then rinse. Treat any residual marks with
bleach.
Ink: depending on the type of ink, moisten
the fabric first with acetone
1)
, then with ace-
tic acid; treat any residual marks on white
fabrics with bleach and then rinse thor-
oughly.
Tar stains: first treat with stain remover, me-
thylated spirits or benzine, then rub with
detergent paste.
Degrees of water hardness
Water hardness is classified in so-called
“degrees” of hardness. Information on
hardness of the water in your area can be
obtained from the relevant water supply
company, or from your local authority.
1) do not use acetone on artificial silk
ENGLISH 13
Characteristic
Degrees of water hardness
German °dH French °T.H.
Soft 0-7 0-15
Medium 8-14 16-25
Hard 15-21 26-37
Very hard > 21 > 37
A water softener must be added when water has a medium-high degree of hardness.
Follow the manufacturer’s instructions. The quantity of detergent can then always be
adjusted (reduced) to degree of hardness soft.
Washing programmes
Please always refer to the care label symbol of your garment and select the washing
programme based on what it says.
Programme/
Temperature
Type of
laundry
Cycle
Description
Max. Load
Red. Load
1)
Available
Options
Detergent
Compartment
COTTONS
90°-60°
White cotton (heavy-
normally soiled
items).
Main wash
Rinses
Max. final
spin at
1200 rpm
6 kg
3 kg
1)
Spin
Rinse Hold
Prewash
Super
Quick
Extra Rinse
2)
3)
COTTONS
ECONOMY
60°-40°
White and fast col-
oured cotton econo-
my, lightly-heavy
soiled items, shirts,
underwear.
Main wash
Rinses
Max. final
spin at
1200 rpm
6 kg
Spin
Rinse Hold
Prewash
Extra Rinse
2)
COTTONS
40°-30°-
(Cold)
Coloured cotton
(normally-lightly
soiled items).
Main wash
Rinses
Max. final
spin at
1200 rpm
6 kg
3 kg
1)
Spin
Rinse Hold
Prewash
Super
Quick
Extra Rinse
2)
ENGLISH 14
Programme/
Temperature
Type of
laundry
Cycle
Description
Max. Load
Red. Load
1)
Available
Options
Detergent
Compartment
SYNTHETICS
60°-40°-30°-
(Cold)
Synthetic or mixed
fabrics: underwear,
coloured garments,
non-shrink shirts,
blouses.
Main wash
Rinses
Max. final
spin at 900
rpm
3 kg
1.5 kg
1)
Spin
Rinse Hold
Prewash
Super
Quick
Extra Rinse
2)
EASY IRON
40°
Synthetic fabrics: se-
lecting this pro-
gramme the laundry
is gently washed and
spun to avoid any
creasing. In this way
ironing is easier. Fur-
thermore the appli-
ance will perform
additional rinses.
Main wash
Rinses
Max. final
spin at 900
rpm
1.5 kg
Spin
Rinse Hold
Prewash
Extra Rinse
2)
DELICATES
40°-30°-
(Cold)
Delicate fabrics: for
example curtains.
Main wash
Rinses
Max. final
spin at 700
rpm
3 kg
1.5 kg
1)
Spin
Rinse Hold
Prewash
Super
Quick
Extra Rinse
2)
WOOL-
HANDWASH
30°-
(Cold)
Special programme
for wool garments
and delicate fabrics
bearing the «Pure
new wool, non-
shrink, appliance
washable» and
«hand washing» la-
bels.
Main wash
Rinses
Max. final
spin at 900
rpm 2 kg
Spin
Rinse Hold
ENGLISH 15
Programme/
Temperature
Type of
laundry
Cycle
Description
Max. Load
Red. Load
1)
Available
Options
Detergent
Compartment
RINSES
With this programme
it is possible to rinse
and spin cotton gar-
ments which have
been washed by
hand. The appliance
performs some rin-
ses, followed by a fi-
nal long spin. The
spin speed can be
reduced.
Rinses
Max. final
spin at
1200 rpm
6 kg
Spin
Rinse Hold
Extra Rinse
DRAIN
For emptying out the
water of the last
rinse in programmes
with the Rinse Hold
option selected.
Draining of
water
6 kg
SPIN
Separate spin for
hand washed gar-
ments and after pro-
grammes with the
Rinse Hold option
selected. You can
choose the spin
speed by pressing
the relevant button
to adapt it to the
fabrics to be spun.
Max. final
spin at
1200 rpm
6 kg
Spin
1) If you select the SUPER QUICK option, we recommend you, to reduce the maximum load as indicated. (Red. load =
reduced load). Full loading is possible however with somewhat reduced cleaning results.
2) If using liquid detergents, a programme without PREWASH must be selected.
3) Standard programmes for the Energy Label consumption values
According to regulation 1061/2010, these programmes are respectively the “standard 60 °C cotton programme”
and the “standard 40 °C cotton programme”. They are the most efficient programmes in terms of combined energy
and water consumptions for washing normally soiled cotton laundry.
Consumption values
The data of this table are approximate. Different causes can change the data: the
quantity and type of laundry, the water and ambient temperature.
ENGLISH 16
Programmes Load
(kg)
Energy con-
sumption
(kWh)
Water con-
sumption (li-
tre)
Approximate
programme
duration (mi-
nutes)
Remaining
moisture
(%)
1)
Cottons 60 °C 6 1.35 59 150 52
Cottons 40 °C 6 0.85 59 140 52
Synthetics 40
°C
30.55 42 90 35
Delicates 40 °C 3 0.55 57 65 35
Wool/Hand
wash 30 °C
20.25 55 60 30
Standard cotton programmes
Standard 60
°C cotton
61.03 45 159 52
Standard 60
°C cotton
30.77 38 135 52
Standard 40
°C cotton
30.64 38 129 52
1) At the end of spin phase.
Off Mode (W) Left On Mode (W)
0.10 0.98
The information given in the charts above are in compliance with the EU Commission reg-
ulation
015/2010 implementing directive 2009/125/EC.
Care and cleaning
Warning! Switch the appliance off
before you carry out any cleaning or
maintenance work.
Maintenance Wash
With the use of low temperature washes it is
possible to get a build up of residues inside
the drum.
We recommend that a maintenance wash
be performed on a regular basis.
To run a maintenance wash:
The drum should be empty of laundry.
Select the hottest cotton wash pro-
gramme.
Use a normal measure of detergent, must
be a powder with biological properties.
Cleaning the dispenser drawer and the
drawer recess
1
To remove the
drawer, press the
catch downwards
and pull it out.
ENGLISH 17
2 To aid cleaning, re-
move also the top
part of the additive
compartment.
3
Use a stiff brush to
clean and remove
all washing powder
residue.
4
Flush out all the re-
moved parts of the
dispenser drawer
under a tap to re-
move any traces of
accumulated pow-
der.
5
Use the previous
brush to clean the
recess, ensuring
that upper and low-
er part of it is well
cleaned.
After having
cleaned the dis-
penser and the
drawer recess, re-
place it and run a
rinse programme
without any laundry
in the drum to flush
away any residue.
Cleaning the pump
Proceed as follows:
1
A
B
Place a container
close to the pump
(A), to collect any
spillage.
2
Pull out the emer-
gency emptying
hose (B), place it in
the container and
remove its cover
cap.
3
When no more wa-
ter comes out, un-
screw the pump
cover (A) and re-
move it. Always
keep a rag nearby
to dry up spillage of
water when remov-
ing the pump.
4
Remove any objects
from the pump im-
peller by rotating it.
ENGLISH 18
5 Use a pencil to
check whether the
pump wheel right at
the back of the
pump housing can
turn. (It is normal for
the pumping wheel
to turn jerkily.) If the
pumping wheel
cannot be turned,
please contact the
After Sales Service.
6
Put the cap back on
the emergency
emptying hose and
place the latter
back in its seat.
Screw the pump
fully in.
Cleaning the water inlet filters
If the appliance takes long to fill with water
or doesn't fill, the starting button indicator
light blinks in red. Check if the water inlet fil-
ters are blocked (see chapter "What to do
if..." for more details).
Proceed as follows:
1
Turn off the water
tap.
Unscrew the hose
from the tap.
Clean the filter in
the hose with a
stiff brush.
Screw firmly the
inlet hose back
onto the tap.
2
Unscrew the hose from the appliance.
Keep a rag nearby because some wa-
ter may flow.
Clean the filter in the valve with a stiff
brush or with the piece of cloth.
3
35°
45°
Screw the hose
back to the appli-
ance turning it to
the left or the
right to suit the
installation. Tight
the locknut cor-
rectly to prevent
water leaks.
Turn on the water
tap.
The dangers of freezing
If the appliance is exposed to temperatures
below 0°C, certain precautions should be
taken.
Turn off the water tap.
Unscrew the inlet hose.
Place the end of the emergency emptying
hose and that of the inlet hose in a bowl
placed on the floor and let water drain
out.
Screw the water inlet hose back on and
reposition the emergency emptying hose
after having put the cap on again.
When you intend to start the appliance
up again, make sure that the room tem-
perature is above 0°C.
ENGLISH 19
Important! Every time you drain the water
through the emergency emptying hose you
must pour 2 litres of water into the main
wash compartment of the detergent drawer
and then run the drain programme. This will
activate the ECO VALVE device avoiding
that part of the detergent remains unused
at next washing.
Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the appliance:
pull out the plug from the power socket;
close the water tap;
if necessary, wait until the water has
cooled down;
open the pump door;
place a bowl on the floor and place the
end of the emergency emptying hose into
the bowl. Remove its cap. The water
should drain by gravity into the bowl.
When the bowl is full, put the cap back
on the hose. Empty the bowl. Repeat the
procedure until water stops flowing out;
clean the pump if necessary as previously
described;
replace the emergency emptying hose in
its seat after having plugged it;
screw the pump cover again and close
the door.
Troubleshooting
The appliance does not start or stops during
operation. It is possible that the red indica-
tor light of button 4 blinks to indicate that
the appliance is not working.
Before contacting your local Service Centre,
please carry out the checks listed below.
Problem Possible cause Solution
The appliance
does not start:
The door has not been closed (The
red indicator light of button 4
blinks).
Close the door firmly.
The plug is not properly inserted in
the power socket.
Insert the plug into the power
socket.
There is no power at the socket. Please check your domestic electri-
cal installation.
The main fuse has blown. Replace the fuse.
The programme selector dial is not
correctly positioned and the button
4 has not been pressed.
Please turn the selector dial and
press the button 4 again.
The delay start has been selected. If the laundry are to be washed
immediately, cancel the delay
start.
The appliance
does not fill:
The water tap is closed The red in-
dicator light of button 4 blinks).
Open the water tap.
The inlet hose is squashed or
kinked (The red indicator light of
button 4 blinks).
Check the inlet hose connection.
ENGLISH 20
1 / 1

IKEA RENLIGWM Benutzerhandbuch

Kategorie
Waschmaschinen
Typ
Benutzerhandbuch

in anderen Sprachen