Ebode LightSpeaker Owner's Manual and Installation Instructions

1

OWNER’S MANUAL

AND INSTALLATION INSTRUCTIONS

State-of-the-art LIGHT & SOUND

One complete system that installs in minutes!

User guide 2

Bedienungsanleitung 30

Gebruiksaanwijzing 58

Användermanual 86

Guide utilisateur 114

Guía del usuario 142

Manual do utilizador 170

Manuale per l’utente 198

One complete system

m

that

installs

in

m

i

tem

2

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufficient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature

accompanying the appliance.

Caution marking is located at the side of the apparatus.

CAUTION: Risk of Electrical Shock - Use in Dry Locations Only

CAUTION: To reduce the risk of electric shock, do not remove cover (or back).

No user servicable parts – refer servicing to qualified service personnel only.

WARNING: To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture.

User Guide LightSpeaker

®

3

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions. Keep these instructions. Heed all Warnings. Follow

all instructions.

2. Do not use this apparatus near water. The apparatus shall not be exposed

to dripping or splashing and that no objects filled with liquids, such as vases,

shall be placed on apparatus.

3. Clean only with a dry cloth.

4. Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

5. Do not install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat.

6. The lamp holder is used as disconnect device. The lamp holder of apparatus

should not be obstructed OR should be easily accessed during intended use.

To completely disconnect the power input, the lamp holder of the apparatus

shall be disconnected from the mains.

7. Only use attachments/accessories specified by the manufacturer.

8. Refer all servicing to qualified service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord

or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

9. Added weight of the device may cause instability of a free-standing lamp.

10. This device is not intended for use with emergency exit fixtures or

emergency exit lights

11. NOT FOR USE WHERE EXPOSED TO THE WEATHER

12. NOT FOR USE IN TOTALLY ENCLOSED RECESSED LUMINAIRES

4

Congratulations

Thank you for choosing a LightSpeaker

®

from ebode

electronics. You have chosen one of the most unique,

patented, audio systems in the world. With proper

installation and operation, you will enjoy years of trouble-

free use. ebode electronics sells numerous products for

use inside or outside your home. To see the complete

ebode electronics product assortment, visit us on the

internet at: www.ebodeelectronics.eu.

5

Table of Contents

System Overview....................................................................................6

What is in this box................................................................................8

Step 1 - Where will you install.........................................................9

Step 2 - Check your connector type...........................................9

Step 3 - Fit your LightSpeaker

®

..................................................10

Step 4 - Setting the zone and stereo switches...................11

Step 5 - Pairing....................................................................................14

Step 6 - Plug in your sources......................................................15

Step 7 - Enjoy your LightSpeakers

®

.........................................16

Operating the transmitter & remote control.......................17

Helpful hints...........................................................................................19

Where to put the transmitter.....................................................20

Specifications.......................................................................................23

Possible causes of interference.................................................26

Troubleshooting the remote.........................................................27

Warranty...............................................................................................28

Questions?............................................................................................29

CE Declaration...................................................................................226

Technical Support Information...................................Back Cover

6

System Overview

This wireless LightSpeaker

®

System is intended to install

into any home easily and

without any expensive and

complicated wiring. You can

install a typical system in

your home in a few minutes

and not have to worry about

repairing walls or ceilings.

Plus there is no climbing into attics or

wriggling into crawl spaces!

LightSpeakers

®

deliver

great sound into any room

in your house. You screw

it in like a bulb into most

recessed fixtures, table

lamps, and pendants, fitting

a standard E27 Edison

screw socket.

This unique patented LightSpeaker

®

has full bandwidth

audio and “green” lighting together in one small package.

Part of what makes this possible is the use of a 10W LED

to provide the equivalent light of a 60W incandescent bulb

while using 80% less power than the light bulb it replaced.

Consider also that you may never have to replace this

light; an operating life of 25,000 to 40,000 hours means

that with average use this light should easily last 15 to 25

years.

7

Your system can use up to 4 pairs of LightSpeakers

®

to provide audio and lighting to your entire home. You

can even divide your home into two unique areas where

different music sources, sound and lighting control allow

you to add music with integrated “green” lighting to places

you only dreamed of having it before.

There’s no wiring and no big (or small) speaker boxes.

The wireless transmitter can be centrally located which

will provide audio and, together with the remote, allow you

to control your LightSpeakers

®

from anywhere in your

home. The RF remote and the transmitter base station

will control which source you listen to in a room as well as

the level of the sound and the brightness of the light; this

can be done from anywhere in the house, you don’t need

to be near the transmitter.

Plug two separate audio sources into your transmitter

and deliver the music from your AM/FM Radio, TV or

MP3, or any audio source, to any room in your house.

To expand your system, additional LightSpeakers

®

are

available from your local dealer.

This incredible patented system provides even greater

flexibility to you as the owner; since you can take this

system with you if you move; and when you do, it leaves no

trace (holes that need to be covered) that the system was

ever installed and used.

Please take a few moments to copy down the serial

number and model number found on the side of

your product box or on the product itself onto the

‘Questions’ page at the end of this manual.

8

Take just a minute to be sure you have everything you

need to install your first wireless distributed audio system

from ebode electronics.

Transmitter Power Cord Large & Small

Trim Rings

LightSpeakers

®

, Remote

Lenses Remote Wall Bracket

Attachment Cords

A h

9

Instruction Manual

Step 1:

Decide which lights will be replaced with

LightSpeakers

®

.

Your

ebode electronics

LightSpeakers

®

have been

specifically designed to cover large areas, however if the

location of your fixtures allow you to do so, you should think

about how you use your room and where you are likely to

spend most of your time. Then choose the fixtures that

are most evenly spaced to your preferred listening position.

A) Turn off the circuit breaker and light switch, to the

bulbs you intend to replace with LightSpeakers

®

.

B) Remove the existing light bulb.

Step 2: Check your connector type. Your ebode

electronics

LightSpeaker

®

is designed to fit into a

standard E27 socket. It will not fit any other type

connector.

WARNING!

Turn off circuit breakers to all lighting

fixtures you are working on!

STOP!

Check your connector!

10

Step 3: Fit your LightSpeaker

®

.

Your LightSpeaker

®

is designed to fit directly into most

recessed fixtures, table lamps and pendants by simply

removing the existing light and, in the same manner as a

light bulb, re-installing your LightSpeaker

®

in its place.

Because of all the technology packed into LightSpeaker,

it is much larger than a normal light bulb, both in length

and width. The best way to use Lightspeaker is in a fitting

where you cannot actually see the sides of the product at

all. As long as the front grille is unrestricted so you can

hear the music and see the light, you do not really want

to see where the sound and light comes from. In general

this means that the ideal is a long, slim lampshade rather

than one short and wide.

Please give this some thought when choosing a fitting for

your LightSpeaker.

Please note - between the front edge of the E27 socket in

your fitting and the front Grille of LightSpeaker you need

to have a shade/fitting that will be at least 15 cm long

and 14 cm wide

At www.ebodeelectronics.eu you can find a selection of

lampmodels that will work with LightSpeaker

11

Step 4: Setting the Zone and L/R Stereo Switches.

A) Set the zone switch on the back of the

LightSpeakers

®

to one, unless you are setting up a

two zone system. For more on zones see Step 4B:

Setting up a Two Zone System below after completing

B and C below.

B) Set the left/right stereo switch. “L” if it is the left

speaker, “R” if it is the right speaker.

C) Your LightSpeaker

®

system allows you to install up

to 4 pairs of (or 8 total) speakers. If you are installing

more than one pair of LightSpeakers

®

you will

probably want to divide your home into zones.

If you are not setting up a two zone system, go to Step 5.

Step 4B: Setting up a Two Zone System

Your system allows you to set up two separate zones.

Zones are the different spaces in your home where you

want to listen to music, and are important because, later in

this setup, your Transmitter will automatically seek out and

identify each zone. This in turn will allow you to control the

music and lighting in each zone separately.

12

Assign Zone 1 to one area and Zone 2 to the other

unique area. (See below figure 2A)

Figure 2A

13

Here we have assigned Zone 1 to the family room, and

Zone 2 to the kitchen area; these are areas where, even

though you are listening to the same music (the same

source), you may still want to control lighting brightness

and speaker volume separately. For example persons

listening to music in the kitchen may want to turn the

music volume lower while those in the family room may

want the turn the music louder and dim the lights. With

two zones each group can have the music and lights the

way they want them without affecting the other group.

Two-Zone System: Assign each LightSpeaker

®

to the

zone where it will be installed.

A) Create a sketch of your anticipated zones (ie.

Figure 2A).

B) Decide what zone the speaker will go into.

C) Place the LightSpeakers

®

in their respective zones.

Set the zone switch, on the back of each

LightSpeaker

®

, to the zone it will be placed.

This LightSpeaker

®

will be used in Zone 1 and is the right

side of a stereo pair.

14

Step 5: Pairing The Transmitter to the speakers

A) Attach the power cord at the “DC IN” connector on

the back of the Transmitter.

B) Turn on the Power Switch.

C) Pairing - This fully automated process will tell the

transmitter where each LightSpeaker

®

is located,

allow you to control each zone separately and make

your LightSpeaker

®

system secure from other nearby

systems. After you have set the zone switch on each

speaker to the correct zone and you have installed

your light speakers into the correct sockets in the

correct zones (i.e. Zone 1 speakers in Zone 1, Zone 2

LightSpeakers™ in Zone 2) the job is nearly finished all

that remains is allowing the transmitter discover where

each of the installed LightSpeakers

®

is located.

1) To pair your LightSpeakers

®

to your

transmitter, turn off all of the light switches in the

areas where LightSpeakers

®

are located.

2) Be sure Transmitter is plugged in and the

power button is on.

3) Push the button marked “PAIRING”. The PAIRING

LED on the transmitter will begin flashing RED.

15

4) Turn on all light switches that your LightSpeakers

®

are connected to. The Small LED

light on the speakers will begin

to flash red and will turn green

when the pairing is complete. The

transmitter will automatically find

each speaker and assign it to its

proper zone.

5) If after 1 minute the LED on the LightSpeaker

®

has not turned “GREEN”, repeat steps 1-4.

a) If after 2 attempts the LED on the

LightSpeaker

®

fails to turn green, try

relocating the Transmitter closer to the

LightSpeaker

®

Step 6: Plugging in your sources.

Using the supplied audio cords, plug your MP3, CD Player,

television or other desired sources to the back of the

transmitter.

Attach 1 or 2 audio sources.

LED Blinks during pairing.

MP3

16

A) Locate the sources you want to use. They will have

audio level outputs on them. Typically these are RCA

or stereo headphone type jacks. You will need to have

the proper cable from the source you want to attach

to the Transmitter. You have two choices:

1) RCA to RCA cable

2) RCA to Stereo Mini Plug Cable

B) If you are attaching only one source it may be

attached to either input but may be convenient to

attach to source one.

Step 7: Enjoy your LightSpeakers

®

!

CAUTION!

Do not use the speaker outputs from

your existing amplifier as this can

damage the transmitter!

17

Operating the Transmitter and Remote Control:

The remote control and

the transmitter are

controlled in exactly the

same manner.

When you push a button

on the transmitter the

small LED next to the

button will light up and remain lit until you push another

button affecting either that zone or that source. The

LEDs that are lit will tell what action the remote or

transmitter is currently set to control.

Here are the steps to take to operate the Transmitter

and Remote Control:

A) Press the zone you want to control

B) When the LED next to the button lights, that zone

is active and will be playing the source that is currently

lit. To change to a different source simply press the

source with the “unlit” LED until the LED next to the

source you are choosing lights.

C) Pressing Light once makes the light go On/Off

D) Pressing the + arrow above the light “on” button

will increase the brightness of the light. Pressing the

“-” arrow below the light on/off button will dim the

light. The LED will flash when the arrows are pushed

and will turn red and flash quickly when either the

maximum or minimum brightness is reached.

18

E) Pressing and holding the ON/OFF button turns ON

or OFF all Zones with source 1 playing if turned ON.

F) When Power is applied to a LightSpeaker

®

by the

wall switch the light defaults to the ON state. This

allows the LightSpeaker’s LED to function like a light

bulb.

NOTE: If your remote does not operate, or you have

purchased additional remotes to be used with the

same transmitter, please see the Trouble shooting

section in this manual.

19

Helpful Hints

Installing and Removing the Lens:

A) Removal BEFORE your LightSpeaker

®

is installed.

1) While holding the LightSpeaker

®

in the palm of your hand

rotate the unit until one of the holding tabs is facing up.

2) Using a fingernail, common screwdriver or other small

flat object, gently push down and then out on the tab, easing

it out through the opening in the

LightSpeaker

®

housing.

3) When the lens pops up, gently pry it away from

the housing, being gentle and making sure not to

break the tabs.

CAUTION: Do not touch the LED or Speaker Baffle

with the lens off when the unit is hot, allow the unit

to cool down before touching the LED.

20

B) Removal of the lens AFTER your LightSpeaker

®

has

been installed.

1) There are three small indentations around the

lens; with a small tip common screwdriver, nail file,

paper clip or similar object, gently slip the tip into

the indentation and pry the lens outward until the

retaining tabs pull free.

2) To re-install the lens, align the tabs and the

hole for the pairing LED, then push gently until the

locking tabs snap into place.

More Ab

Where to put the transmitter?

Typically, the perfect place for your transmitter is near

your home entertainment system, if you have one. If you

don’t have a home audio system then you can chose

a place that is centrally located to the rooms you will

be transmitting the audio to. Remember the range of

the system is approximately 15 meter* radius circle

of the transmitter, so as long as the distance from the

transmitter to the farthest speaker in any direction is less

than 15 meters*, the placement of the transmitter is up

to you.

Note: There is a maximum of two transmitters in one

home and they need to be 8 meters* apart.

*Range depending on environmental conditions.

Seite laden ...

Ebode LightSpeaker Owner's Manual and Installation Instructions

Dieses Handbuch ist auch geeignet für

Ebode LightSpeaker Owner's Manual and Installation Instructions

in anderen Sprachen

Verwandte Papiere

Sonstige Unterlagen