Elac PPA-2 Phono Preamplifier Bedienungsanleitung

Marke: Elac

Modell: PPA-2 Phono Preamplifier

Kategorie: Musikausrüstung

Typ: Bedienungsanleitung

PPA-2 PHONO PREAMPLIFIER

OPERATING INSTRUCTIONS

Alchemy

™

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 1

Safety Instructions

1. General information

• Please read and follow these safety instructions.

• Keep them safe for future reference.

• Observe all warnings on the preampliﬁer and in the manual. Please check the ampliﬁer for damage

before use. The ampliﬁer must be in perfect working condition. Damaged parts may lead to personal

injury.

2. Use only as directed

• Connect the preampliﬁer according to the instructions in the manual.

3. Location

• Install the preampliﬁer on a level surface only

• When choosing the location of the preampliﬁer do not place them in locations that are:

• In direct sunlight

• Very humid

• Prone to vibrations

• Exceptionally hot or cold

WARNING! Please ensure the product is perfectly stable to avoid injury from tip-over. Do not install the preampli-

ﬁer near any heat sources such as radiators, heating valves, stoves, or other apparatus that produce heat, or in

areas where there is a risk of explosion.

• Do not block any ventilation openings. Install in accordance with the instructions.

• Do not install the preampliﬁer in a closed rack or in a closed cupboard.

• Do not put burning candles on or near the preampliﬁer.

• Do not install the preampliﬁer near transformers because electromagnetic stray ﬁelds can cause hum

noise.

• In combination with certain materials / lacquers / material surfaces, anti-slip feet may cause colored

imprints on the surfaces.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 2

4. Overload

• Extreme overload of the device due to very high volume may cause damage to individual components.

Because of the possible danger, you should never leave the ampliﬁer under extreme overload conditions

unattended.

5. Service

• DANGER! Do not open the ampliﬁer because there may be dangerous voltages inside. Servicing to be

carried out by qualiﬁed service personnel only.

• Servicing is required when the ampliﬁer has been damaged in any way, such as damage to the power

supply cord or the plug, or when liquid has been spilled or objects have fallen onto the ampliﬁer, the

ampliﬁer has been exposed to rain or moisture, does not operate normally, or has been dropped. To

reduce the risk of electric shock, do not open the ampliﬁer. Servicing should be carried out by qualiﬁed

service personnel only.

6. Cleaning

• NOTE: Clean only with soft, smooth cloth or with dust brush. Do not use scouring agents, alcohol,

benzene, furniture polish or other agents for cleaning! Modern furniture is often coated with multiple

varnishes and plastics which can be treated with chemical agents. Some of these agents contain

substances which degrade or soften the rubber feet. Therefore we advise that you place an anti-slip mat

underneath the ampliﬁer.

7. Volume

• CAUTION! Continuous high volume may cause severe damage to your hearing. Please listen responsibly.

8. Disposal

• The packaging is made from recyclable materials. Dispose of this in an environmentally friendly manner.

At end of life dispose of the preampliﬁer as e-waste. The ampliﬁer must be recycled in accordance with

local legislation. Ask your local government for further information on recycling as the device contains

valuable raw materials.

Philosophy

Thank you for purchasing this ELAC product.

Since the time we started (1926), ELAC has always striven to achieve the very best.

Your new ELAC ampliﬁer is built to the highest standards using high-quality components that are carefully

constructed to deliver the best-in-class sound quality. They are developed by a passionate group of individuals

whose sole purpose is to bring a new dimension of sound quality into your home. Enjoy!

Before Use

Avoid damage to the ampliﬁer and other components:

• Carefully unbox the ampliﬁer to avoid physically damaging your preampliﬁer.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 3

Controls and Indicators

1. POWER Button—Used to power the phono preampliﬁer on and o

2. MUTE Indicator — This LED will illuminate when the MUTE function is active

3. Input 1 Indicator—This LED will illuminate when Input 1 is active

4. Input 2 Indicator—This LED will illuminate when Input 2 is active

5. High Pass Filter Indicator—This LED will illuminate when the High Pass Filter is active

6. MC (Moving Coil) Indicator—This LED will illuminate when the phono preamp is in MC mode

7. L+R (Mono) Indicator LED—This LED will illuminate when the mono feature is active

8. MUTE Button—Used to activate the MUTE Function which will disable all output of the preamp when

active

9. INPUT 1/2 Button—Used to switch between Input 1 or 2

10. HP (High Pass Filter) Button—Used to activate the High Pass ﬁlter (Rumble Filter)

11. MC/MM Button—Used to select either MM (Moving Magnet) or MC (Moving Coil) style cartridges

12. MONO Button—Used to switch the preamp from Stereo to Mono operation for playback of mono records.

13. GND Terminal—Used to ground the turntable to signal ground (See Page 6 for additional details)

14. Chassis Ground—Used to ground the turntable to chassis/ac mains ground (See page 6 for additional

details)

15. Input 1 (RCA) —Used when connecting to an unbalanced RCA based turntable

16. Input 2 (RCA) - Used when connecting to an unbalanced RCA based turntable

17. Input 2 (XLR) - Used when connecting to a balanced XLR based turntable

18. RCA Outputs—Used when connecting to an unbalanced RCA based preampliﬁer/receiver

19. XLR Outputs—Used when connecting to a balanced XLR based preampliﬁer/receiver

20. 18V Accessory Connector—Used to power certain ELAC Miracord turntables

21. AC Inlet—Used to supply power to phono preamp. Connect to an available AC outlet.

22. OEL Display—Use to display various information for setup and usage

23. Variable Loading Adjustments—Used to adjust the loading when setting up a new cartridge for either

input 1 or 2

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 4

Wiring the Inputs

Connecting a turntable to the PPA-2 Phono preamp

Phono 1 is Unbalanced only (RCA jacks), Phono 2 can be either Balanced (XLR jacks) or Unbalanced.

Cables from the turntable to the PPA-2 should be as far as possible from AC Mains cables wherever possible. If

they must cross, do so at right angles if you can.

Typically a balanced connection will be more immune to hum, so it would be the preferred connection.

However, you must be careful that the shell of the XLR is not connected directly to the ground line within the

XLR connector. They SHOULD be independent. The shell is the external shield of the cable and connector, and

should be the CHASSIS connection. The ground wire within the XLR is twisted with the (+) and (-) balanced and

should be the signal or tonearm ground. This can all be conﬁrmed with an Ohm meter.

Whichever style you choose, please use the very best cable you can in this location due to the very low signal

levels coming from your phono cartridge.

After you make your audio connections refer to Page 8 to correctly set the DIP switches.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 5

Wiring the Outputs

Connecting the PPA-2 to a Pre-Ampliﬁer, Receiver, or Integrated Ampliﬁer

The PPA-2 provides both Unbalanced (RCA jacks) and Balanced (XLR jacks) outputs. Typically a balanced

connection will be more immune to hum, so it would be the preferred connection. Again, please use the best

quality cables you can between PPA-2 and your control preampliﬁer.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 6

Grounding

Correctly grounding an audio system for minimum hum and maximum signal-to-noise ratio can be very

complicated, and will vary from system to system.

PPA-2 has two dierent ground posts, each at dierent ground potentials; SIGNAL and CHASSIS. SIGNAL is at

the ground potential of the input signal. CHASSIS is that of the AC Mains ground connection; typically used as a

shield.

If your turntable has only one ground connection, usually that will connect to CHASSIS. If you have a separate

ground wire from the arm it should go to the SIGNAL ground, and the turntable motor or body ground wire

should go to CHASSIS.

Initial Power On

After making all necessary audio and grounding connections. Plug the included power cord to an available wall

outlet.

Press the Power button to turn on the PPA-2.

At initial power on the PPA-2 will go through a brief warmup period during which it will be in mute. You will see

the Alchemy Series Logo on the front panel display as the unit warms up. The screen will go blank just before

PPA-2 unmutes and restores the last known status condition of all functions; INPUT 1 or 2, Filter, Gain and Mode.

This ﬁrst time it is powered on it will be on INPUT 1, no ﬁlter, low gain and in stereo.

Selecting Cartridge Type

There are several technologies of phono cartridge available. The PPA-2 works with Moving Magnet (“MM”) and

Moving Coil (“MC”) types. USUALLY MM cartridges are designed to operate into a nominal load impedance of

47K Ohms. MC cartridges are typically loaded with much lower values from 5 Ohms to a few hundred Ohms

up to maybe as much as 1000 Ohms. There are always exceptions to these rules, so check to be sure. The

PPA-2 lets you select this load precisely through use of a continuously adjustable potentiometer and built-in

measurement system. Please refer to ﬁgure 1 for the DIP switch settings to correctly select either the ﬁxed 47K

or adjustable load for Inputs 1 and 2 separately.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 7

Cartridge Load Measurement

If you need to set the adjustable load, ﬁrst look up the suggested loading for your particular cartridge model in

the manufacturers speciﬁcations. Also check a few of the known audio columnists to see what their reviews

might suggest for optimum loading. Sometimes one will ﬁnd a large discrepancy between these resources. The

PPA-2 makes it easy to test these various choices. A rough rule-of-thumb is that loading should be about 10

times the source impedance speciﬁcation for the cartridge. This, and suggestions from resources you might ﬁnd

will, in the end, just be guidelines. The beauty of the adjustment method PPA-2 uses is that you can adjust up

and down from the suggested starting points to achieve what sounds best for you in your system.

With PPA-2 powered ON and the appropriate input selected, press the SELECT button. PPA-2 screen will come

on and tell you that you have entered measurement mode and will show the current LEFT and RIGHT load

settings. Note that audio is muted during the measurement process.

Turn the load pots on the back panel associated with the input in question and you will see the readings on

the screen change. Set both the LEFT and RIGHT adjustment knobs to the desired loading. It’s a bit fussy

as the controls are quite sensitive, but with some patience you will get it to where you want to be. Pressing

the SELECT button again will switch to the exit screen where measurement mode will automatically exit in 15

seconds and put the display to sleep. To exit immediately, press SELECT again during the countdown.

To set the adjustable loading for the alternate input you must select that input and then enter measurement

mode again by pressing SELECT and following the instructions above.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 8

Settings and Adjustments

The PPA-2 has a row of LED status indicators followed by a row of buttons to control the indicated functions.

Please refer to Figure 2.

MUTE lights when the MUTE button is pressed. This feature is convenient when changing tracks or making

some kind of adjustment that could otherwise result in an objectionable noise. Press once to engage, again to

disengage.

1 & 2 refer to the Input numbers on the back of PPA-2. Pressing the INPUT 1 or INPUT 2 button toggles between

them. INPUT 1 is on the far left (as viewed from the back) and INPUT 2 is on the other side of the dip switches

(where you have already selected 47K or adjustable load, and if INPUT 2 is to be balanced or unbalanced, right?)

When lit indicates that the High Pass (i.e. rumble) ﬁlter has been selected with the HP button. Toggle to

switch. This mode is useful if your turntable has a bit of low frequency noise, or if the cut you are playing has so

much bass that is causes feedback from your turntable (sometimes known as howling.)

+18db Indicates when the PPA-2 is in high gain (MC) mode and is toggled by the MC/MM button and will

obviously be louder in the lit condition. Pick the position where you have sucient volume in your system to

play as loud as you need. There is no advantage to high gain mode if you don’t need it, it will only be noisier but

not sound any better.

L+R Indicates MONO mode and is toggled by the MONO button. Use mono when playing mono records or

when you are checking channel balance or some other test.

TWEAKING

As noted above, select the gain position you feel gives sucient volume range for your listening tastes. Don’t

use more gain than you need, there is no point.

Once you have sound and are starting to listen critically you should notice great dynamics from the PPA-2, as

well as extended range in both the bass and treble regions. Smoothness and dimensionality will be excellent,

but none of these will be as good as they will be after a week of warmup, perhaps even several weeks.

If you are using the adjustable load feature and you want to, you can start to make ﬁne adjustments to the load

for each channel to see if you like the sound better one way or the other. While valid now for better enjoyment

during the warmup period, ultimately you will want to make these same changes once the PPA-2 stabilizes as

they may be subtly dierent.

Note that for tweaking the load you do not enter measurement mode; to do so would mute the audio and you

need to be listening for this step. The idea is to put on a record with which you are very familiar and very slightly

increase the left and right loads and listen to the results. Then, reduce the load very slightly and listen again.

You might need to iterate this process a number of times till you feel you have gotten the best sound you can

achieve. At this point the actual load number has likely been altered from the original settings you made. If you

want, you can enter measurement mode and read the settings you have gotten to, for future reference.

MODE SELECTION

Other than gain, the PPA-2 has two modes you can select, as needed, to improve performance under certain

conditions; MONO and HP. Their purpose is described above. Each will be remembered as your preferred

setting upon power o, so be sure to disengage them when not needed.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 9

Settings and Adjustments

TROUBLESHOOTING

No sound or low volume? Do you have the correct input selected? Do you need to be in High gain (+18db)

mode? Is your cartridge loading set so low that the cartridge is not producing enough output? Are you using

INPUT 2 RCA or XLR without switching the dip switches to the correct mode? Are you in MUTE?

Measured load not changing? Check that the DIP switch setting for 47K/Adjustable are in the Adjustable

position. Are you turning the correct knob for the Input you are measuring?

Acoustic Feedback causing howling? Switch on the High Pass ﬁlter.

Audible hum in the system. See the grounding section on Page 8. The PPA-2 itself is very, very quiet, so if you

are hearing hum it is caused by something else in your system. There is most likely something in your system

causing it and you need to look at your grounding, wire position or for some other problem. It should, and will

be, quiet and hum-free.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 10

SPECIFICATIONS

Inputs (2) RCA UNBALANCED or (1) RCA & (1) XLR BALANCED

Input impedance 5-1KOhms variable or 47K

Frequency response 10hz-20khz +/- 0.2dB

RIAA accuracy +/- 0.2dB

Nominal THD+N <0.005%

Signal-to-noise ratio (1 kHz) >86dB

Output Voltage >6.0V RMS

Crosstalk (L-to-R or R-to-L) >80dB

Single ended Gain 42dB (low) or 60dB (high)

Balanced Gain 48dB (low) or 66dB (high)

Output impedance 50 Ohms

Analog Outputs (1) XLR BALANCED, (1) RCA UNBALANCED

Available ﬁnishes Black

Dimensions (HxWxD) 2" x 17.5" x 15" including jacks

Weight 12 lbs

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 11

ELAC Americas Inc.

North America Limited Liability Warranty

Passive Speakers (No built-in ampliﬁer)

ELAC Americas INC. warrants to the original purchaser that this product be free from defects and or

workmanship for a period of3 (Three)years from the original date of purchase. During this time period, repair or

replacement of parts will be free of charge to the original owner (See below limitations). Shipping to and return

from the repair center will be the responsibility of the original purchaser.

Powered Subwoofers

ELAC Americas INC. warrants to the original purchaser that this product be free from defects and or

workmanship for a period of3 (Three)years on the cabinet and speaker driver and1 (One)year on the ampliﬁer

from the original date of purchase. During this time period, repair or replacement of parts will be free of

charge to the original owner (See below limitations). Shipping to and return from the repair center will be the

responsibility of the original purchaser.

Electronics (Including Wireless Speakers)

ELAC Americas INC. warrants to the original purchaser that this product be free from defects and or

workmanship for a period of1 (One)years from the original date of purchase. During this time period, repair or

replacement of parts will be free of charge to the original owner (See below limitations). Shipping to and return

from the repair center will be the responsibility of the original purchaser.

B-Stock (Reconditioned/Open Box) Product Warranty

ELAC Americas INC. warrants to the original purchaser that this product be free from defects and or

workmanship, unless otherwise stated in product description, for a period of90 daysfrom the original date of

purchase. During this time period, repair or replacement of parts will be free of charge to the original owner

(See below limitations). Shipping to and return from the repair center will be the responsibility of the original

purchaser.

Limitations

Warranty begins on the date of original purchase from an authorized ELAC Americas Inc. dealer.

Product is warranted only if used in home applications within the max power rating speciﬁed in this manual.

Commercial use of this product is not warranted.

Product that has been modiﬁed or altered in anyway will not be warranted.

Product that has been abused or subjected to faulty equipment will not be warranted.

Products with defaced or removed serial numbers will not be warranted.

If service is required

In the event that service is required, please contact ELAC America at 888-541-0996 or atcustomerservice@elac.

usto arrange for service or replacement. You will be responsible to provide proof of purchase (Copy or original

sales receipt). Shipping to and from our repair center will be the responsibility of the original purchaser.

Warranty Outside of North America

This warranty applies to products purchased in the United States and Canada. For warranty claims outside of

North America please contact the local dealer/distributor in the country of purchase.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 12

DU PRÉAMPLIFICATEUR PHONO PPA-2

MODE D’EMPLOI

Alchemy

™

Consignes de sécurité

1. Informations générales

• Veuillez lire et suivre ces consignes de sécurité.

• Conservez-les aﬁn de les consulter ultérieurement.

• Respectez tous les avertissements inscrits sur le préampliﬁcateur et dans le manuel. S'il vous plaît,

vériﬁez si le préampliﬁcateur est endommagé avant de l'utiliser. Le préampliﬁcateur doit être en parfait

état de fonctionnement. Les pièces endommagées peuvent causer des blessures corporelles.

2. Utilisez seulement selon les directives.

• Connectez l’appareil conformément aux instructions du manuel.

3. Emplacement

• Installez l’appareil uniquement sur une surface plane

• Lorsque vous choisissez l'emplacement du préampliﬁcateur, ne le placez pas aux endroits suivants :

• Sous les rayons directs du soleil

• Très humides

• Sujets aux vibrations

• Très chauds ou très froids

ATTENTION! Aﬁn d'éviter toute blessure causée par le basculement de cet appareil, veuillez-vous assurer qu'il

est parfaitement stable. N'installez pas le préampliﬁcateur à proximité de sources de chaleur telles que des

radiateurs, des valves de chauage, des poêles ou autres appareils qui produisent de la chaleur ou dans des

endroits présentant des risques d'explosion.

• Ne bloquez pas les ouvertures de ventilation. Installez conformément aux instructions.

• N'installez pas le préampliﬁcateur dans un espace conﬁné ou un placard fermé.

• Ne placez pas de bougies allumées sur ou près du préampliﬁcateur.

• N'installez pas le préampliﬁcateur à proximité de transformateurs car des champs parasites

électromagnétiques peuvent provoquer des bourdonnements OHM.

• En combinaison avec certains matériaux/vernis/surfaces de matériaux, les pieds antidérapants ou les

rondelles des pointes peuvent laisser des traces colorées sur les surfaces.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 1

4. Surcharge

• Une surcharge extrême de l'appareil en raison d'un volume très élevé pourrait endommager

certains composants de l'appareil. En raison de dangers potentiels, vous ne devez jamais laisser le

préampliﬁcateur sans surveillance lors de conditions de surcharge extrême.

5. Entretien

• DANGER! N'ouvrez pas le préampliﬁcateur car il pourrait y transiter une tension électrique dangereuse à

l'intérieur. L’entretien doit être uniquement eectué par un personnel qualiﬁé.

• Un entretien est nécessaire lorsque le préampliﬁcateur a été endommagé de quelque manière que ce

soit, tel que l'endommagement du cordon d'alimentation ou de la ﬁche électrique, ou si du liquide a été

renversé ou si des objets sont tombés sur le préampliﬁcateur, si le préampliﬁcateur a été exposé à la

pluie ou à l'humidité, s'il ne fonctionne pas normalement, ou s'il a été échappé. Pour réduire les risques

d'électrocution, n'ouvrez pas l'ampliﬁcateur. L'entretien doit être uniquement eectué par un personnel

qualiﬁé.

6. Nettoyage

• REMARQUE : Nettoyez uniquement avec un chion doux et souple ou une brosse à dépoussiérer.

N’utilisez pas de produits abrasifs, d’alcool, de benzène, de cire pour meubles ou autres produits de

nettoyage! Le mobilier moderne est souvent revêtu de multiples couches de vernis et de plastique qui

peuvent être traités avec des agents chimiques. Certains de ces agents contiennent des substances qui

dégradent ou ramollissent les pieds en caoutchouc. Par conséquent, nous vous conseillons de placer un

tapis antidérapant sous l’ampliﬁcateur.

7. Volume

• ATTENTION! Un volume élevé en continu peut endommager gravement votre audition. Veuillez utiliser

les haut-parleurs à un niveau sonore convenable.

8. Recyclage

• L’emballage est fabriqué à partir de matériaux recyclables. Mettez l’appareil au rebut de façon

écologique. En ﬁn de vie utile, éliminez le préampliﬁcateur avec les déchets électroniques. Le

préampliﬁcateur doit être recyclé conformément à la réglementation locale. Informez-vous auprès de vos

autorités locales pour obtenir de plus amples renseignements sur le recyclage, car l’appareil contient

des matières premières précieuses.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 2

Philosophie

Merci d’avoir fait l’achat de ce produit ELAC.

Depuis nos débuts en 1926, ELAC a toujours aspiré à atteindre l’excellence.

Votre nouvel ampliﬁcateur ELAC est conçu selon les normes les plus élevées. Il est doté de composantes de

qualité supérieure qui sont soigneusement fabriqués pour procurer la meilleure qualité sonore de leur catégorie.

Ils sont conçus par des gens passionnés dont le seul but est d’amener à votre foyer une nouvelle dimension de

qualité sonore. Proﬁtez-en!

Avant l’utilisation

Évitez d’endommager les haut-parleurs et les autres composantes :

• Déballez soigneusement le préampliﬁcateur pour éviter d’endommager physiquement votre

préampliﬁcateur.

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 3

Commandes et

1. Bouton marche/arrêt « POWER » - Utilisé pour allumer et éteindre l’ampliﬁcateur

2. Indicateur « MUTE » - Ce voyant s’allume lorsque la fonction MUTE est activée.

3. Indicateur d’entrée 1 : Ce voyant s’allumera lorsque l’entrée 1 sera activée.

4. Indicateur d’entrée 2: Ce VOYANT s’allume lorsque l’entrée 2 est activée.

5. Indicateur de ﬁltre passe-haut - Ce VOYANT s’allume lorsque le ﬁltre passe-haut est actif.

6. Indicateur MC (Moving Coil): Ce VOYANT s’allume lorsque le préampli phono est en mode MC.

7. Indicateur L + R (Mono) : Ce VOYANT s’allume lorsque la fonction mono est activée.

8. Bouton sourdine « MUTE » - Utilisé pour activer la fonction sourdine « MUTE » qui désactivera toutes les

sorties du préampli lorsqu’il est actif.

9. Bouton d’entrée 1 et 2 « INPUT 1-2 » : Utilisé pour basculer entre les entrées 1 ou 2

10. Bouton HP (ﬁltre passe-haut): Utilisé pour activer le ﬁltre passe-haut (ﬁltre anti-vibration)

11. Bouton MC / MM - Utilisé pour sélectionner les cartouches de style MM (aimant mobile) ou MC (bobine

mobile)

12. Bouton « MONO » — Utilisé pour faire passer le préampli du mode stéréo au mode mono lors de l’écoute

d’enregistrements mono.

13. Borne de mise à la terre « GND »— Utilisée pour relier le tourne-disque à la mise à la terre (voir page 6

pour plus de détails).

14. Masse du châssis « Chassis Ground » - Utilisée pour relier le tourne-disque à la masse du châssis/ mise à

la terre du bloc d’alimentation (Voir page 6 pour plus de détails).

15. Entrée 1 (RCA) « Input 1 » : Utilisée lors d’une connexion RCA à un tourne-disque asymétrique.

16. Entrée 2 (RCA) « Input 2 » - Utilisée lors d’une connexion RCA à un tourne-disque asymétrique

17. Entrée 2 (XLR) « Input 2 » - Utilisée lors de la connexion à un un tourne-disque symétrique XLR

18. Sorties RCA - Utilisées lors de la connexion à un préampliﬁcateur/récepteur asymétrique RCA

19. Sorties XLR « OUTPUT » - Utilisées lors de la connexion à un préampliﬁcateur/récepteur symétrique XLR

20. Connecteur accessoire 18 V - Utilisé pour alimenter certains tournes-disques ELAC Miracord

21. Entrée CA— Utilisée pour alimenter le préampli du tourne-disque. Connectez-vous à une prise CA

disponible.

22. Achage DELO - Permet d’acher diverses informations sur la conﬁguration et l’utilisation

23. Ajustements du chargement des variables - Utilisés pour ajuster le chargement lors de la conﬁguration

d’une nouvelle cartouche pour l’entrée 1 ou 2

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 4

Branchement des entrées

Connexion d’un tourne-disque au préampli Phono PPA-2

Le Phono 1 est uniquement asymétrique (prises RCA), le Phono 2 peut être symétrique (XLR) ou asymétrique.

Les câbles du tourne-disque au PPA-2 doivent être aussi éloignés que possible des câbles d’alimentation, dans

la mesure du possible. S’ils doivent se croiser, faites-le à angle droit si vous le pouvez.

En règle générale, une connexion (XLR) sera plus immunisée au ohm ce qui en fait un type de branchement à

privilégier. Cependant, vous devez faire attention à ce que la coque du XLR ne soit pas connectée directement

à la ligne de terre dans le connecteur XLR. Ils DOIVENT être indépendants. La coque est le blindage externe du

câble et du connecteur et doit être la connexion au CHASSIS. Le ﬁl de mise à la terre dans le XLR est torsadé

avec un (+) et un (-) équilibrés et doit être la masse du signal ou du bras de lecture. Tout ceci peut être conﬁrmé

avec un ohmmètre.

En raison du niveau de signal très faible provenant de votre cartouche phono et quel que soit le style que vous

choisissez, veuillez utiliser le meilleur câble possible à cet emplacement.

Après avoir eectué vos connexions audio, reportez-vous à la page 8 pour régler adéquatement les

commutateurs DIP.

Tourne-disque

Diagramme avec XLR equilibre

Tourne-disque

Diagramme avec RCA non equilibre

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 5

Branchement des

Branchement du DPA-2 d’Alchemy à un préampliﬁcateur, un récepteur ou un ampliﬁcateur intégré

Le PPA-2 fournit à la fois des sorties asymétriques (prises RCA) et équilibrées (prises XLR). En règle générale,

une connexion (XLR) sera plus immunisée au ohm ce qui en fait un type de branchement à privilégier. Encore

une fois, veuillez utiliser les câbles de la meilleure qualité possible entre PPA-2 et votre préampliﬁcateur de

contrôle.

Preampliﬁcateur Phono Alchemy PPA-2

Preampliﬁcateur Alchemy DDP-2

Diagramme avec RCA non equilibre

Preampliﬁcateur Phono Alchemy PPA-2

Preampliﬁcateur Alchemy DDP-2

Diagramme avec XLR equilibre

ELAC Alchemy PPA-2 Phono Preampliﬁer | www.elac.com | Page 6

Seite laden ...

Elac PPA-2 Phono Preamplifier Bedienungsanleitung

Marke: Elac

Modell: PPA-2 Phono Preamplifier

Kategorie: Musikausrüstung

Typ: Bedienungsanleitung

PDF Herunterladen

Bericht

in anderen Sprachen

English: Elac PPA-2 Phono Preamplifier Owner's manual
français: Elac PPA-2 Phono Preamplifier Le manuel du propriétaire

Elac PPA-2 Phono Preamplifier Bedienungsanleitung

Elac PPA-2 Phono Preamplifier Bedienungsanleitung

in anderen Sprachen

Verwandte Papiere

Sonstige Unterlagen