Pressalit RK1111 Benutzerhandbuch

UK: Indivo lift units for the kitchen

User and maintenance guide

DK: Indivo løfteenheder til køkken

Brugs- og vedligeholdelsesvejledning

NO: Indivo løfteenheter til kjøkken

Bruks- og vedlikeholdsveiledning

SE: Indivo lyftutrustning för kök

Bruks- och underhållsanvisning

DE: Indivo Hubeinheiten für die Küche

Gebrauchs- und Pegeanleitung

FR: Cadres de réglage en hauteur Indivo pour cuisine

Manuel d’utilisation et d’entretien

ES: Dispositivos de elevación para cocina Indivo

Funcionamiento y mantenimiento

NL: Indivo-liften voor de keuken

Gebruiks- en onderhoudshandleiding

RK1010 – RK1011 – RK1012

RK1013 – RK1014 – RK1020

RK1021 – RK1081 – RK1082

RK1083 – RK1100 – RK1101

RK1110 – RK1111 – RK1112

RK1113 – RK1114 – RK1181

RK1182 – RK1183

2

English ............................................................................................. 3

Dansk .............................................................................................21

Norsk ..............................................................................................39

Svenska ..........................................................................................57

Deutsch ..........................................................................................75

Français ..........................................................................................93

Español .........................................................................................111

Nederlands ....................................................................................129

UK: The guarantee covers faults or defects in material or manufacture within a period of 3 years.

Products are subject to minor technical modications and design deviations. E. & O.E.

DK: Garantien dækker i 3 år fra fakturadato for materiale- og fabrikationsfejl.

Der tages forbehold for trykfejl, tekniske ændringer og modelafvigelser.

NO: Garantien gjelder i 3 år fra fakturadato for material- og fabrikasjonsfeil.

Med forbehold for trykkfeil, tekniske endringer og modellforskjeller.

SE: Garantin gäller i 3 år från fakturadatum för material- och fabrikationsfel.

Med reservation för tryckfel, tekniska ändringar och modellavvikelser.

DE: Die Garantie gilt für drei Jahre ab Rechnungsdatum für Material- und Herstellungsfehler.

Druckfehler, technische Änderungen und Modellabweichungen vorbehalten.

FR: La garantie couvre les vices de fabrication et de matériaux pour une durée de 3 ans à partir

de la date de facturation. Sous réserve de modications techniques et d’erreurs d’impression.

ES: La garantía cubre fallos de material o fabricación durante los tres años posteriores a partir de

la fecha de factura. Mantenemos reservas en caso de problemas de presión, modicaciones

técnicas y variaciones de modelo.

NL: De garantie is tot 3 jaar na factuurdatum geldig voor materiaal- en fabricagefouten.

Onder voorbehoud van drukfouten, technische wijzigingen en modelafwijkingen.

3 år / 3 years / 3 jahre / 3 ans

Garanti / Guarantee / Garantie

3

Thank you for choosing this Pressalit Care lift unit

for kitchens.

Combined with either a worktop or wall cabinet, the lift unit

makes it possible to create a height-adjustable kitchen,

ensuring the best working conditions for all users.

We hope that helpers and users will beneﬁ t from the multiple

functions and advantages of the unit:

• Pressalit Care lift units are available in 6 variants:

1 Electrical lift units for worktops.

2 Manual lift units for worktops.

3 Manual lift units for worktops.

4 Electrical lift units for freestanding tables.

5 Manual lift units for freestanding tables.

6 Electrical lift units for wall cabinets.

• The ﬂ exibility of the units makes it easy for helpers

and users to work together in the kitchen.

• The Indivo range includes three lift systems: electrical

and manual - both of which can be adjusted daily - and

inﬁ nitely adjustable, suitable for periodical adjustment.

• Indivo can be combined with worktops and wall cabinets

at your discretion.

• Regardless of the combinations you choose, our safety

systems provide optimum safety.

1

2

3

5

4

6

4

Important safety information

Please read and become familiar with the user and

maintenance guide before using the lift unit. Pressalit Care

cannot be held liable if the product is used in any way which

differs from that described in the guide.

• The information in the guide is based on correct ﬁ tting

of the lift unit in accordance with our installation guide.

• If the product is defective or damaged, it must not be

used before it has been repaired by a service engineer.

• For safety reasons, nothing should obstruct the lift unit

when in movement. 7

• The product is not intended for play, and we therefore

recommend that it is not operated by children without

adult supervision.

• We reserve the right to amend this guide without prior

notice.

Before using the lift unit for the ﬁ rst time

• Users, helpers and therapists must read and be familiar

with this user and maintenance guide before using the

unit.

• Keep this guide in the immediate proximity of the lift unit.

• Check that the unit's control box (models with electric

motor only) is suitable for the mains electricity supply.

• Kitchen lift units are for indoor use only.

7

5

8

9

10

max

100 kg

(165 lbs)

max

100 kg

(220 lbs)

max

100 kg

(220 lbs)

max

100 kg

(220 lbs)

(243 lbs)

max

110kg

max

110 kg

(243 lbs)

(485 lbs)

max

220kg

max

220 kg

(485 lbs)

11

12

Electrical lift units

Maximum load

Wall-mounted 8

100 kg, incl. worktop.

Freestanding 9

100 kg, incl. worktop.

Wall cabinet 10

1 motor bracket: 110 kg incl. cabinet

2 motor brackets: 220 kg incl. cabinet

Operation

• The height of the lift units can be adjusted using the

switches on the frame.

• As an alternative or supplement to the frame-mounted

switches 11 a hand-held control unit is available.13

Adjustment

Wall-mounted

• The height of the electric lift unit can be set using the

frame-mounted switch 11 or hand-held remote control 13 ,

which has an up/down indicator. Raise the unit by

pressing and holding the upper part of the indicator.12

Lower the unit by pressing and holding the lower part

of the indicator. Release the indicator to stop the unit.

• When the unit is mounted at the recommended height,

it can be adjusted between 670 and 950 mm above the

ﬂ oor.

Freestanding

• The height of the electric lift unit can be set using

the frame-mounted switch 11, which has an up/down

indicator. Raise the unit by pressing and holding the

upper part of the indicator.12 Lower the unit by pressing

and holding the lower part of the indicator. Release the

indicator to stop the unit.

• The unit can be adjusted to heights of between 680 and

980 mm above the ﬂ oor.

Wall cabinet

• The height of the lift unit can be adjusted using the

switches on the frame 11 or hand-held remote control.13

• When wall cabinets are lowered 430 mm to their lowest

position, they are also projected 180 mm towards the

user.

Electrical lift units

13

6

Maintenance

• We recommend running the motors on the unit to their

maximum positions at least once a week by raising the

unit to its full height, and then lowering it to its lowest

position, so that the internal, self-lubricating parts are

lubricated.14

• Reset the unit to maintain its smooth up/down

movement.15 Press the indicator until the unit stops at its

lowest position - release the lower indicator - press once

more and hold for 5 seconds.

Service inspection

We recommend that a service inspection is performed once

annually.

Wall-mounted

1. Run the unit up/down 16 to check that:

a. there are no visible defects or abnormal noise.

b. the product runs up/down satisfactorily.

If there are no visible defects or abnormal noises coming

from the moving parts, no further action is required.

If a telescopic leg is defective, it must be replaced.

(Contact your dealer for replacement).

2. Check the wall brackets and tighten if necessary. If the

brackets need tightening, raise the worktop to maximum

height. Support and remove the worktop with its

longitudinal proﬁ le.17 Lower the telescopic legs to their

lowest position.18 Slacken the two screws behind the legs,

and remove the legs.19 Tighten wall bracket bolts.20

Replace the telescopic legs in reverse order, and raise

them. Fit the worktop with its longitudinal proﬁ le 21.

3. Check all electrical connections to the control box. If the

transformer is defective, it must be replaced (contact

your dealer for replacement).

4. Check the supports are correctly ﬁ tted.22

5. Check the operating switch.23 If the switch is defective,

it must be replaced. (Contact your dealer for

replacement).

6. Check for broken cables or wires.

7. Check the safety device (if ﬁ tted in the kitchen). Check

that the safety device rails/plates can move freely and

return to their neutral position. Check whether the lift

unit stops when the safety device is operated.

Electrical lift units

1

23

Min.

5Sek.

15

14

16

17

18

7

1

3

2

1

19

20

NB!

24

22

21

23

Freestanding

1. Run the lift unit up/down to check that:

a. there are no visual defects or abnormal noise.

b. the product runs up/down satisfactorily.

If there are no visible defects or abnormal noises coming

from the moving parts, no further action is required.

If a telescopic leg is defective, it must be replaced.

(Contact your dealer for replacement).

2. Check all electrical connections to the control box.

If the transformer is defective, it must be replaced.

(Contact your dealer for replacement).

3. Check the operating switch.23 If the switch is defective,

it must be replaced. (Contact your dealer for

replacement).

Wall cabinet

1. Run the lift unit up/down to check that:

a. there are no visual defects or abnormal noise.

b. the product runs up/down satisfactorily.

If there are no visible defects or abnormal noises coming

from the moving parts, no further action is required.

If the unit is defective, it must be replaced. (Contact

your dealer for replacement).

2. Check the wall brackets and tighten if necessary.

If the wall units have to be tightened, run the unit out/

down a little, and tighten the lower screws. Run the unit

all the way out/down, and tighten the upper screws.23

3. Check all electrical connections to the control box.

If the transformer is defective, it must be replaced

(contact your dealer for replacement).

4. Check the operating switch.24 If the switch is defective,

it must be replaced. (Contact your dealer for

replacement).

Electrical lift units

8

Faultﬁ nding

Wall-mounted lift unit for worktop

Fault Cause Remedy

Lift unit for

worktop without

safety rail

cannot be height-

adjusted.

No power. Check mains electricity is correctly

connected to the control box. a

(The control box will usually be located

under the worktop).

Telescopic legs not

mounted at the same

height.

Mount the telescopic legs at the same

height and level.

A sink or installation

cover collides with an

obstruction.

Check whether the installation cover

comes into contact with the skirting board

or the like.

Lift unit has not been

reset (e.g. after power

loss).

Reset the unit if possible:

1. Activate the indicator until the unit is in

its lowest position. Release the switch.

2. Activate the lower indicator again for

5 seconds.

3. The lift unit is now reset. (It may be

necessary to reset the unit several times

in succession).

Faulty plugs. Check plug from motor to extension lead,

and those in inlets 1 and 2 on the control

box. The male plugs have small steel pins

which can be easily bent when inserted

into the control box. If one of the pins is

bent, straighten it out before replacing

the plug in the control box. REMEMBER

to reset.

The frame-mounted

switch cannot be

operated easily.

Check whether the switch can be operated

freely and that it returns automatically to

neutral position. The movement can be

hindered by dirt or grease.

Check the frame-mounted switch:

Check that all wires are correctly

connected according to the installation

guide and that none are broken.

If a wire is incorrectly connected, the lift

unit cannot run up or down.

NB: If the lift unit will not rise, the switch

can be considered as defective.

If all wires from the switch are correctly

connected and none are broken, the

lift unit should be able to run up/down.

REMEMBER to reset.

Electrical lift units

a

9

Lift unit for

worktop with

safety rail

cannot be height-

adjusted.

Fault in safety device. The worktop cannot run up or down if the

safety rail is defective.

Check that all wires and plugs are intact

and correctly connected according to the

installation guide.

Installation error on

safety rail. Use measurement device b (ohmmeter)

to detect current. Measure current on

the wire from the safety rail and its plug

(a close function).

- if there is current, the safety device

system is working. The lift unit should now

run up/down. REMEMBER to reset.

- if no current can be detected, remove

the plastic covers and slacken the screws

at the end of the safety rail. The rail should

now move freely. Note that the rail's

freedom to move can be hindered by dirt

or grease.

- check for current once more:

If there is current, the safety device

system is working. If no current can be

detected, see under "Faulty switches".

Faulty switches. Check whether one or more of the safety

system contacts is sticking, and if so,

attempt repair. If the problem cannot be

ﬁ xed, replace the contact(s). The safety

system will only work when current can be

detected. REMEMBER to reset.

Electrical lift units

1

2

b

10

Lift unit for

worktop and

wall cabinet with

safety rail/plate,

cannot be height-

adjusted

Fault in safety system. The worktop/wall cabinet cannot run up

or down if the safety rail/plate is defective.

Check that all wires and plugs are intact

and correctly connected according to the

installation guide.

Installation error on

safety rail/plate. Use measurement device c (ohmmeter)

to detect current. Measure current on the

wires from the safety rail/plate and their

plug (a close function).

- if there is current, the safety device

system is working. The lift units should

now run up/down. REMEMBER to reset.

- if no current can be detected:

a. remove the plastic corners on the safety

rail, and slacken the screws at both ends.

The rail should now move freely. Note

that the rail's freedom to move can be

hindered by dirt or grease.

Check for current once more:

If there is current, the safety device

system is working. If no current can be

detected, see under "Faulty switches".

b. slacken all screws on the safety plate

until it can move freely. Note that the

plate's freedom to move can be hindered

by dirt or grease.

Check for current once more:

If there is current, the safety device

system is working. If no current can be

detected, see under "Faulty switches".

Faulty switches. Check whether one or more of the safety

system contacts is sticking, and if so,

attempt repair. If the problem cannot be

ﬁ xed, replace the contact(s). The safety

system will only work when current can be

detected. REMEMBER to reset.

Jumper missing

in safety device box. If there is a combination in which one of

the safety inputs in the safety device box

is not in use, that input must be ﬁ tted with

a jumper lead. If a jumper lead is missing,

the worktop will not run, although the wall

cabinets will run up and down correctly.

See installation guide.

When jumper lead and other safety device

plugs d (mk. 5 and 6) are inserted, both

worktop and wall cabinet will run up and

down correctly.

Note that in some instances, 2 safety

device boxes are used e, of which one is

marked 8-9-10.

If the lift units run up/down correctly, all

safety systems are working correctly.

REMEMBER to reset.

Electrical lift units

5

6

5

6

5

6

7

5

6

7

5

6

7

5

6

7

8

9

10

8

9

10

88

5

6

5

6

2

1

3

5

6

5

6

c

d

e

11

Freestanding lift units for worktop

Fault Cause Remedy

Lift unit for

worktop without

safety rail

cannot be height-

adjusted

No power. Check mains electricity is correctly

connected to the control box. f.

(The control box will usually be located

under the worktop).

Lift unit has not been

reset (e.g. after power

loss).

Reset the unit if possible:

1. Activate the indicator until the unit is

in its lowest position. Release the switch.

2. Activate the lower indicator again for

5 seconds.

3. The lift unit is now reset. (It may be

necessary to reset the unit several times

in succession).

Faulty plugs. Check plug from motor to extension lead,

and those in inlets 1 and 2 on the control

box. The male plugs have small steel pins

which can be easily bent when inserted

into the control box. If one of the pins

is bent, straighten it out before replacing

the plug in the control box. REMEMBER

to reset.

The frame-mounted

switch cannot be

operated easily.

Check whether the switch can be operated

freely and that it returns automatically to

neutral position. The movement can be

hindered by dirt or grease.

Check the frame-mounted switch:

Check that all wires are correctly connected

according to the installation guide and that

none are broken.

If a wire is incorrectly connected, the lift

unit cannot run up or down.

NB: If the lift unit will not rise, the switch

can be considered as defective.

If all wires from the switch are correctly

connected and none are broken, the lift

unit should be able to run up/down.

REMEMBER to reset.

Electrical lift units

f

12

Lift unit for

worktop with

safety rail

cannot be height-

adjusted.

Fault in safety system. The worktop cannot run up or down if the

safety rail is defective.

Check that all wires and plugs are intact

and correctly connected according to the

installation guide.

Assembly error on

safety rail system. Use measurement device g (ohmmeter)

to detect current. Measure current on

the wire from the safety rail and its plug

(a close function).

- if there is current, the safety device

system is working. The lift unit should now

run up/down. REMEMBER to reset.

- if no current can be detected:

Remove the plastic corners on the safety

rails and slacken the screws at both ends.

The rails should now move freely. Note that

the rails' freedom to move can be hindered

by dirt or grease.

Check for current once more:

If there is current, the safety device system

is working. If no current can be detected,

see under "Faulty switches".

Faulty switches. Check whether one or more of the safety

system contacts is sticking, and if so,

attempt repair. If the problem cannot be

ﬁ xed, replace the contact(s). The safety

system will only work when current can be

detected. REMEMBER to reset.

Electrical lift units

1

2

g

13

Lift units for wall cupboards

Fault Cause Remedy

Lift unit for wall

cupboard without

safety plate

cannot be height-

adjusted.

No power. Check mains electricity is correctly

connected to the control box. h (The

control box will usually be located under

the worktop).

Lift unit has not been

reset (e.g. after power

loss).

Reset the unit if possible:

1. Activate the indicator until the unit is in

its lowest position. Release the switch.

2. Activate the lower indicator again for

5 seconds.

3. The lift unit is now reset. (It may be

necessary to reset the unit several times

in succession).

Faulty plugs. Check plug from motor to extension lead,

and those in inlets 3 and 4 on the control

box. The male plugs have small steel pins

which can be easily bent when inserted

into the control box. If one of the pins

is bent, straighten it out before replacing

the plug in the control box. REMEMBER

to reset.

The frame-mounted

switch cannot be

operated easily.

Check whether the frame-mounted

switch can be operated freely and that it

returns automatically to neutral position.

The movement can be hindered by dirt

or grease.

Check the frame-mounted switch:

Check that all wires are correctly

connected according to the installation

guide and that none are broken.

If a wire is incorrectly connected, the lift

unit cannot run up or down.

NB: If the lift unit will not rise, the switch

can be considered as defective.

If all wires from the switch are correctly

connected and none are broken, the lift

unit should be able to run up/down.

REMEMBER to reset.

h

Electrical lift units

14

Lift unit for wall

cupboard with

safety plate

cannot be height-

adjusted

Fault in safety system. The wall cabinet cannot run up or down

if the safety plate is defective.

Check that all wires and plugs are intact

and correctly connected according to the

installation guide.

Assembly error on

safety plate. Use measurement device i (ohmmeter)

to detect current. Measure current on

the wire from the safety rail and its plug

(a close function).

- if there is current, the safety device

system is working. The lift unit should now

run out/down. REMEMBER to reset.

- if no current can be detected:

Slacken the screws on the safety plate.

The plate should now move freely. Note

that the plate's freedom to move can be

hindered by dirt or grease.

Check for current once more:

If there is current, the safety device

system is working. If no current can be

detected, see under "Faulty switches".

Faulty switches. Check whether one or more of the safety

system contacts is sticking, and if so,

attempt repair. If the problem cannot be

ﬁ xed, replace the contact(s). The safety

system will only work when current can be

detected. REMEMBER to reset.

1234

3

3 3

i

Electrical lift units

15

Lift units for

worktop and

wall cabinet with

safety plates/rails

cannot be height-

adjusted.

Fault in safety system. The worktop/wall cabinets cannot run up

or down if the safety rail/plate is defective.

Check that all wires and plugs are intact

and correctly connected according to the

installation guide.

Installation error on

safety rail/plate. With measurement device (ohmmeter) j

to detect current. Measure current on the

wires from the safety rail/plate and their

plug (a close function).

- if there is current, the safety device

system is working. The lift units should

now run up/down. REMEMBER to reset.

- if no current can be detected:

a. slacken all screws on the safety plate

until it can move freely. Note that the

plate's freedom to move can be hindered

by dirt or grease.

Check for current once more:

If there is current, the safety device

system is working. If no current can be

detected, see under "Faulty switches".

b. remove the plastic corners on the safety

rail, and slacken the screws at both ends.

The rail should now move freely. Note that

the rail's freedom to move can be made

hindered by dirt or grease.

Check for current once more:

If there is current, the safety device

system is working. If no current can be

detected, see under "Faulty switches".

Faulty switches. Check whether one or more of the safety

system contacts is sticking, and if so,

attempt repair. If the problem cannot be

ﬁ xed, replace the contact(s). The safety

system will only work when current can be

detected. REMEMBER to reset.

Jumper lead missing in

fuse box. If there is a combination in which one of

the safety inputs in the safety device box

is not in use, that input must be ﬁ tted with

a jumper lead. If a jumper lead is missing,

the worktop will not run, although the wall

cabinets will run up and down correctly.

See installation guide.

When jumper lead and other safety device

plugs (mk. 5 and 6) are inserted, both

worktop and wall cabinet will run up and

down correctly.

Note that in some instance, 2 safety device

boxes are used, of which one is marked

8-9-10.

If the lift units run up/down correctly, all

safety systems are working correctly.

REMEMBER to reset.

Contact Pressalit Care or your dealer if the problem cannot

be remedied. Do not attempt to repair the product yourself,

as this will invalidate the guarantee.

2

1

3

5

6

5

6

j

Electrical lift units

16

Manual lift units

Maximum load

Wall-mounted 25

100 kg, incl. worktop.

Freestanding 26

100 kg, incl. worktop.

Operation

Wall-hanging/freestanding

Remove 27 hand crank from under worktop and ﬁ t onto

drive shaft. If there is a frame around the worktop, push the 28

over the drive shaft to one side and ﬁ t the hand crank.

Adjustment

Wall-hanging/freestanding

• Adjust the manual lift unit for height by turning the hand

crank.29

• Always stop turning the crank when you feel resistance at

either the upper or lower position.30

• The unit can be adjusted to heights of between 680 and

980 mm above the ﬂ oor.

Maintenance

• We recommend winding the spindle on the unit to the

maximum positions at least once a week. by raising the

unit to its full height, and then lowering it to its lowest

position, so that the internal, self-lubricating parts are

lubricated.31

Min.

NB!

Max

NB!

27

(220 lbs)

ma x

100kg

max

100 kg

(220 lbs)

max

100 kg

(220 lbs)

max

100 kg

(220 lbs)

25

26

28

29

31

30

Manual lift units

17

Service inspection

We recommend that a service inspection is performed once

annually.

Wall-mounted

1. Run the lift unit up/down to check that:

a. there are no visual defects or abnormal noise.

b. the product runs up/down satisfactorily.

If there are no visible defects or abnormal noises coming

from the moving parts, no further action is required.

If a telescopic leg is defective, it must be replaced.

(Contact your dealer for replacement).

2. Check the wall brackets and tighten if necessary. If the

brackets need tightening, raise the worktop to maximum

height. Support the worktop with its longitudinal proﬁ le,

and remove the angle gear and proﬁ le.32

Remove the

worktop. The crank extension rod will hang free.33

Insert the crank in the extension rod, wind the worktop

down and remove.34 Slacken the two screws behind the

legs, and remove the legs.35 Tighten wall bracket bolts.36

Replace the telescopic legs in reverse order, and raise

them. Fit the worktop with its longitudinal proﬁ le37

3. Check the supports are correctly ﬁ tted.38

4. Check the crank.39 If the crank is defective, it must be

replaced. (Contact your dealer for replacement).

Freestanding

1. Run the lift unit up/down to check that:

a. there are no visual defects or abnormal noise.

b. the product runs up/down satisfactorily.

If there are no visible defects or abnormal noises coming

from the moving parts, no further action is required.

If a telescopic leg is defective, it must be replaced.

(Contact your dealer for replacement).

2. Check the legs and tighten if necessary.

3. Check the crank.40 If the crank is defective, it must be

replaced. (Contact your dealer for replacement).

34

1

3

2

1

35

36

33

32

Manual lift units

18

Faultﬁ nding

Wall-mounted

Fault Cause Remedy

Lift unit does not run

synchronously. The telescopic legs are

not mounted at the same

height (not level).

Run the unit as far down

to its lowest position as

possible. Detach the

longitudinal shaft on the side

where the leg is highest.

Insert an Allen key into the

leg and turn until the leg is

fully retracted.

The lift unit does not move

when the hand crank is

turned.

The crank is not correctly

ﬁ tted on the drive shaft. Push the crank down as far

as it will go and turn until

the worktop moves up and

down.

The extension rod is not

correctly attached to the

angle gear.

Connect the rod correctly

to the gear.

(See installation guide).

The angle gear is not

correctly attached to the

longitudinal drive shaft

between the two telescopic

legs.

Connect the gear correctly

to the drive shaft. (See

installation guide).

Freestanding

Fault Cause Remedy

Lift unit does not run

synchronously. The telescopic legs are

not mounted at the same

height (not level).

Run the unit as far down

to its lowest position as

possible. Detach the

longitudinal shaft on the side

where the leg is highest.

Insert an Allen key into the

leg and turn until the leg is

fully retracted.

The lift unit does not move

when the hand crank is

turned.

The crank is not correctly

ﬁ tted on the drive shaft. Push the crank down as far

as it will go and turn until

the worktop moves up and

down.

The extension rod is not

correctly attached to the

angle gear.

Connect the rod correctly to

the gear. (See installation

guide).

The angle gear is not

correctly attached to the

longitudinal drive shaft

between the two telescopic

legs.

Connect the gear correctly

to the drive shaft. (See

installation guide).

Contact Pressalit Care or your dealer if the problem cannot

be remedied. Do not attempt to repair the product yourself,

as this will invalidate the guarantee.

NB!

38

37

5

39

5

40

Manual lift units

19

Inﬁ nitely variable lift units

Maximum load 41

75 kg, incl. worktop.

Operation

When the inﬁ nitely variable lift unit is ﬁ tted in accordance

with the installation guide, the unit is ready for use.

Adjustment

Adjust the unit by slackening the screw. The unit can then be

set to the desired height. Retighten the screw.42

Service inspection

We recommend that a service inspection is performed once

annually.

1. Check the supports. Replace any broken supports.

Support the worktop and remove it from the support.43

Detach the support from the wall bracket by unscrewing

and removing the bolt. 43 Fit a new support in the

reverse sequence.

2. Check the wall brackets and tighten if necessary.

Remove supports when tightening (including worktop)

from the wall bracket by unscrewing and removing

the bolts.44 The wall brackets can now be tightened.45

Replace the parts in reverse sequence.

Faultﬁ nding

Fault Cause Remedy

Worktop not level. The telescopic legs are not

mounted at the same height

(not level).

If the supports cannot be height

adjusted, check the threaded

insert mounted inside the

bracket. There must be no screw

heads in the way of the threaded

inset.

If the supports cannot be

secured at a given height, we

recommend adjusting the height

a little before trying again.

(165 lbs)

max

75 kg

42

45

43

44

(165 lbs)

max

75 kg

max

75 kg

(165 lbs)

max

75 kg

(165 lbs)

41

Inﬁ nitely variable lift units

20

General

Cleaning

Daily

Use ordinary soapy water. Avoid use of abrasive, corrosive or

chlorine-based cleaning products. Rinse off with clean water

and dry with a soft cloth.

These products cannot be cleaned in an autoclave.

Occasional

Use 3 parts 30% household vinegar to 7 parts water for

removal of lime deposits. Wipe off with a cloth dipped in

clean water and wrung out.

CE

The CE mark indicates that this product has been

manufactured according to the Machine Directive

2006/42/EC of 17 May 2006.

Information on disposal and recycling

Electrical and electronic equipment (EEE) contains materials,

components and substances which can be hazardous to

human health and the environment when waste from electric

and electronic equipment (WEEE) is not disposed of correctly.

Such equipment must not be disposed of with unsorted

domestic refuse, but must be collected separately. Waste

must be processed according to local authority instructions.

Seite wird geladen ...

Pressalit RK1111 Benutzerhandbuch

Dieses Handbuch eignet sich auch für

Pressalit RK1111 Benutzerhandbuch

in anderen Sprachen

Verwandte Artikel

Andere Dokumente