Silvercrest SFS 120 A1 Operating Instructions Manual

IAN 288381

VACUUM SEALER SFS 120 A1

VACUUM SEALER

Operating instructions

ΣΥΣΚΕΥΗ ΑΕΡΟΣΤΕΓΟΥΣ

ΣΦΡΑΓΙΣΗΣ ΤΡΟΦΙΜΩΝ

Οδηүίες χρήσης

VAKUUMIERER

Bedienungsanleitung

GB / IE / NI / CY Operating instructions Page 1

GR / CY Οδηүίες χρήσης Σελίδα 17

DE / AT / CH Bedienungsanleitung Seite 33

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες

της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A

B



















!3-



.0

GB

│

IE

│

NI

│

CY

│

1 ■

SFS 120 A1

Contents

Introduction ...................................................2

Copyright ............................................................... 2

Limitation of liability ....................................................... 2

Intended use ..................................................2

Package contents and transport inspection .........................3

Unpacking .............................................................. 3

Disposal of packaging materials ............................................. 3

Description of the appliance .....................................4

Technical data .................................................4

Safety guidelines ..............................................5

Setting up and connecting .......................................7

Set-up location requirements ................................................ 7

Electrical connection ...................................................... 7

Welding a tube ﬁlm .............................................8

Vacuuming the tube ﬁlm ........................................10

Cleaning .....................................................12

Cleaning the appliance ................................................... 12

Storage .....................................................12

Disposal .....................................................13

Kompernass Handels GmbH warranty ............................13

Service ................................................................ 15

Importer ............................................................... 15

Ordering replacement parts ....................................16

■ 2

│

GB

│

IE

│

NI

│

CY

SFS 120 A1

Introduction

Congratulations on the purchase of your new appliance!

You have decided in favour of a modern, high-quality product. These operating

instructions are part of this product. They contain important information on safety,

usage and disposal. Before using the product, familiarise yourself with all handling

and safety guidelines. This appliance may only be used as described and for the

purposes indicated. Please also pass these operating instructions on to any future

owner(s).

Copyright

This documentation is protected by copyright.

Any reproduction, or any reprint even in the form of excerpts, as well as the rendi-

tion of ﬁgures even in modiﬁed form, is only permitted with the manufacturer’s

written consent.

Limitation of liability

All the technical information, data and instructions regarding installation, connec-

tion and operation contained in these operating instructions corresponds to the

latest information available to us at the time of printing and takes our previous

experience and know-how into account.

No claims can be derived from the details, illustrations and descriptions in these

instructions.

The manufacturer assumes no responsibility for damage caused by failure to

observe these instructions, improper use, incompetent repairs, unauthorised

modiﬁcations or for the use of non-approved replacement parts.

Intended use

This appliance is intended exclusively for the sealing and vacuum-packing of

foodstuﬀs in household quantities and only in private households. This device is

not intended for commercial or industrial applications or for continuous use.

It is not intended for any other use or use beyond that speciﬁed. Claims of any

kind for damage arising as a result of incorrect use will not be accepted.

The risk shall be borne solely by the user.

GB

│

IE

│

NI

│

CY

│

3 ■

SFS 120 A1

Package contents and transport inspection

The appliance is supplied with the following components as standard:

▯ Vacuum Sealer

▯ 1 x tube ﬁlm

▯ 1x replacement sealing ring

▯ These operating instructions

NOTE

► Check the package for completeness and for signs of visible damage.

► If the consignment is incomplete or damaged due to defective packaging

or carriage, contact the Service hotline (see the chapter Service).

Unpacking

♦ Remove the appliance, the tube ﬁlm and the operating instructions from the

carton.

♦ Remove all packaging material.

♦ Remove the protective ﬁlm from the control panel.

DANGER

► Packaging materials should not be used as a plaything. Risk of suﬀocation.

Disposal of packaging materials

The packaging protects the appliance from damage during carriage.

The packaging materials have been selected for their environmental friendliness

and ease of disposal, and are therefore recyclable.

Returning the packaging to the materials cycle conserves raw materials and

reduces the amount of waste that is generated. Dispose of packaging materials

that are no longer needed in accordance with applicable local regulations.

NOTE

► If possible, keep the original packaging during the warranty period so that

the device can be properly packed for returning in the event of a warranty

claim.

■ 4

│

GB

│

IE

│

NI

│

CY

SFS 120 A1

Description of the appliance

Figure A

 Appliance lid

 Suction tube

 Cable retainer

 Welding wires

 Lower sealing ring

 Rear limiters

 Front limiters

 Lid release

 Upper sealing ring

 Press seal

Figure B

- Red control lamp

3

button (seal)

! button (stop)

.

button (vacuum/welding)

0 Green control lamp

Technical data

Operating voltage 100 - 240 V ∼, 50/60 Hz

Power consumption 120 W

Protection class

II /

GB

│

IE

│

NI

│

CY

│

5 ■

SFS 120 A1

Safety guidelines

RISK OF ELECTRIC SHOCK

■ Prior to use, check the device for visible external damage.

Never operate an appliance that is damaged.

■ To avoid risks, arrange for a defective power cable to

be replaced by qualiﬁed technicians or by our Customer

Service Department.

■ NEVER use the appliance with a defective power cable.

■ Do not use extension cables or power socket strips that do

not meet the required safety standards.

■ Never open the appliance housing!

■ Remove the plug from the mains power socket before be-

ginning to clean the device.

■ Ensure that no moisture can penetrate the device during

cleaning.

RISK OF INJURY!

■ All repairs must be carried out by authorised special-

ist companies or by the Customer Service department.

Improper repairs may result in a risk of injury to the user

or damage to the appliance. They will also invalidate any

warranty claim.

■ The mains power socket must be easily accessible, so that

the power cable can be easily disconnected in the event

of an emergency.

■ 6

│

GB

│

IE

│

NI

│

CY

SFS 120 A1

RISK OF INJURY!

■ Cleaning and user maintenance tasks may not be carried

out by children unless they are supervised.

■ The appliance and its connecting cable must be kept

away from children younger than 8 years old.

■ This appliance may be used by children aged 8 years

and above and by persons with limited physical, sensory

or mental capabilities or lack of experience and knowl-

edge, provided that they are under supervision or have

been told how to use the appliance safely and are aware

of the potential risks.

■ Children must not play with the appliance!

■ Children should be supervised to ensure that they do not

play with the appliance.

■ Do not leave the appliance unsupervised when it is ready

for use. To prevent it being switched on accidentally, al-

ways unplug the appliance after use or during breaks.

CAUTION – PROPERTY DAMAGE!

■ Do not use an external timer switch or a separate remote

control system to operate the appliance.

GB

│

IE

│

NI

│

CY

│

7 ■

SFS 120 A1

Setting up and connecting

Set-up location requirements

For safe and trouble-free operation of the device , the set-up location must fulﬁl

the following requirements:

■ When setting it up, place the appliance on a ﬁrm, ﬂat and horizontal

surface.

■ Do not place the device in a hot, wet or extremely damp environment or in

the vicinity of ﬂammable materials.

■ The mains power socket must be easily accessible, so that the power cable

can be easily disconnected in the event of an emergency.

Electrical connection

CAUTION

► Before you connect the appliance, compare the connection data (voltage

and frequency) on the data plate with that of your mains power network.

These data must agree so that no damage is sustained by the device.

► Ensure that the power cable is undamaged and is not routed over hot

surfaces and/or sharp edges.

► Ensure that the power cable is not taut or kinked.

► Do not let the power cable hang over edges (trip wire eﬀect).

♦ Insert the plug into the mains mains power socket.

■ 8

│

GB

│

IE

│

NI

│

CY

SFS 120 A1

Welding a tube ﬁlm

NOTES ON THE FILM

► The ﬁlm width may not exceed 28 cm. Otherwise it cannot be welded

correctly.

► Use only nylon-PE ﬁlms with a structure (points or grooves) on one side and

that have a structure (points or grooves) on one side and a thickness of

approximately 0.17 - 0.29 mm (170 - 290 μ).

Otherwise the weld seam will not be tight and the appliance may be da-

maged. You can recognise ﬁlms of this type from the information on the

packaging. The quality of the weld seam will vary depending on the type

and thickness of the ﬁlm.

► The supplied ﬁlm is suitable for temperatures between -20°C and +100°C.

1) Cut the desired length for your bag from the tube ﬁlm using a pair of scissors.

Cut as straight as possible.

2) Open the appliance lid  by pressing the lid release  and opening the

lid  upwards.

3) Lay the open end of the bag as far into the appliance so that the opening of

the bag is located centrally under the lower sealing ring . The bag should

be inserted no further than the rear limiters  and must lie between the front

limiters . If the bag lies over one or both of the two limiters , then the

bag cannot be correctly welded.

GB

│

IE

│

NI

│

CY

│

9 ■

SFS 120 A1

NOTE

► The bag opening must lie ﬂat on the welding wire . Otherwise the weld-

ing does not work properly.

4) Close the appliance lid . The press seal  presses the bag onto the welding

wire , to create a smooth seam. Ensure that both corners of the appliance

lid  click closed. If necessary, press them down once again on the markings

and so that the appliance lid  clicks into place and locks shut.

5) Press the

button 3. The red control lamp - lights up. As soon as the

sealing process is ﬁnished, the red control lamp - goes oﬀ.

NOTE

► You can halt the sealing process at any time by pressing the

button !.

The red control lamp - goes out.

CAUTION – PROPERTY DAMAGE!

If the red control lamp - does not go out after a maximum of

10 seconds, there is a fault with the appliance.

► Remove the plug from the mains power socket immediately. Do not attempt

to repair the appliance yourself. Contact the Customer Service department.

6) Open the appliance lid  by pressing the lid release  and ﬂipping the lid 

upwards. Remove the bag. This is now sealed at one end.

NOTE

► Ensure that the weld seam is properly closed. A correct weld seam should

be a smooth, straight stripe without any creases.

7) Fill the bag. You must leave at least 6 cm of the bag free up to the edge to

be welded.

CAUTION – PROPERTY DAMAGE!

► Fill the bag so that no food scraps or liquids can leak out during welding

and get into the appliance.

8) If you do not want to vacuum the bag, you can now weld the other, open side.

NOTE

► Wait 15 seconds before sealing the next bag to allow the appliance to

cool down.

During this cool-down phase, you cannot start the “seal” function.

■ 10

│

GB

│

IE

│

NI

│

CY

SFS 120 A1

Vacuuming the tube ﬁlm

You can also suck the air out of the bag (vacuum) during welding:

CAUTION – PROPERTY DAMAGE!

►

Do not evacuate bags that contain liquids. These will get into the appliance

and damage it.

1) Lay the open end of the bag as far into the appliance so that the opening of

the bag is located centrally under the lower sealing ring . The bag should

be inserted no further than the rear limiters  and must lie between the front

limiters . Otherwise the vacuuming and welding will not function correctly:

2) Close the appliance lid . Ensure that both corners of the appliance lid 

click closed. If necessary, press them down once again on the markings

and so that the appliance lid  clicks into place and locks shut.

NOTE

► Ensure that the upper  and the lower sealing rings  are not damaged!

Otherwise the device cannot suck the air out of the bag.

► If either one of the sealing rings / is damaged, simply pull it out of the

groove and press the replacement sealing ring into the groove.

GB

│

IE

│

NI

│

CY

│

11 ■

SFS 120 A1

3) Press the button .. The green control lamp 0 lights up and the appliance

sucks the air out of the bag. As soon as all the air is sucked out, the green

control lamp 0 goes out and the red control lamp - lights up. The appliance

now seals the bag.

4) If both control lamps -/0 have gone out, you can open the lid by pressing

the lid catch  and ﬂipping the lid  upwards. Remove the vacuum-sealed

bag.

NOTE

► You can halt the air extraction process at any time by pressing the

button !.

The green control lamp 0 will then go oﬀ. Press the

button . again to

resume the extraction process.

If the appliance has already switched to the sealing process and the red

control lamp - is lit, the process can be stopped with the

button !.

The appliance then stops the sealing process.

► Once you have sealed 5 bags in a row, allow the appliance to cool down

for about 1 minute.

During this cool-down phase, you cannot start the appliance. After the

cool-down phase, you can use the appliance as normal.

TIP – "SOUS-VIDE COOKING"

► As the supplied ﬁlm is suitable for temperatures between -20°C and

+100°C, it can be used for the so-called "sous-vide" cooking process

(vacuum cooking).

"Sous-vide" is French and means "under vacuum".

In vacuum cooking, the food (usually ﬁsh or meat, but vegetables can

also be used) is vacuum-sealed in a bag and then cooked in water or steam

cooked at a relatively low temperature (50 to 90 C). The advantage of this is

that volatile ﬂavours or aroma are not lost during cooking. The food does not

dry out and the vitamins and ﬂavours are preserved. Herbs or spices that are

vacuum-sealed in the bag with the food give oﬀ a more intense ﬂavour.

■ 12

│

GB

│

IE

│

NI

│

CY

SFS 120 A1

Cleaning

DANGER

Risk of fatal injury from electrocution!

► Remove the plug from the mains power socket before beginning to clean

the device.

► Ensure that no moisture can penetrate the device during cleaning.

CAUTION

Possible damage to the appliance.

► Do not use aggressive or abrasive cleaning agents, as these may corrode

the surface of the casing.

► Do not use any hard or sharp objects to remove any adhesive from the

welding wire . Otherwise the welding wire  or the insulation could

be damaged.

Cleaning the appliance

♦ Clean the surface of the housing of the appliance with a lightly moistened

cloth and a mild detergent.

♦ Wipe oﬀ the upper  and the lower sealing rings , as well as the press

seal  with a damp cloth. Ensure that the appliance is dry before using it

again.

Storage

The appliance has a built-in cable retainer  on the underside of the housing,

on which you can wrap the power cable when it is not in use. This prevents the

power cable from getting caught or soiled, or becoming a source of danger by

hanging loosely down.

CAUTION

Possible damage to the appliance.

► Do not click the appliance lid  closed for storage! When the appliance

lid  is clicked closed it exerts permanent pressure on the upper  and

lower sealing rings , as well as the press seal . This can negatively

aﬀect their function.

♦ Store the appliance in a clean, dry place away from direct sunlight.

GB

│

IE

│

NI

│

CY

│

13 ■

SFS 120 A1

Disposal

Under no circumstances should you dispose of the appliance

with the normal household waste.

This product is subject to the provisions of European Directive

2012/19/EU (Waste Electrical and Electronic Equipment).

Dispose of the appliance via an approved waste disposal company or your

municipal waste disposal facility. Please observe applicable regulations. In

case of doubt, please contact your waste disposal centre.

Kompernass Handels GmbH warranty

Dear Customer,

This appliance has a 3-year warranty valid from the date of purchase. If this product

has any faults, you, the buyer, have certain statutory rights. Your statutory rights

are not restricted in any way by the warranty described below.

Warranty conditions

The validity period of the warranty starts from the date of purchase. Please keep

your original receipt in a safe place. This document will be required as proof of

purchase.

If any material or production fault occurs within three years of the date of purchase

of the product, we will either repair or replace the product for you at our discretion.

This warranty service is dependent on you presenting the defective appliance

and the proof of purchase (receipt) and a short written description of the fault

and its time of occurrence.

If the defect is covered by the warranty, your product will either be repaired or

replaced by us. The repair or replacement of a product does not signify the begin-

ning of a new warranty period.

Warranty period and statutory claims for defects

The warranty period is not prolonged by repairs eﬀected under the warranty.

This also applies to replaced and repaired components. Any damage and defects

present at the time of purchase must be reported immediately after unpacking.

Repairs carried out after expiry of the warranty period shall be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accordance with strict quality guidelines

and inspected meticulously prior to delivery.

The warranty covers material faults or production faults. The warranty does not

extend to product parts subject to normal wear and tear or fragile parts such as

switches, batteries, baking moulds or parts made of glass.

■ 14

│

GB

│

IE

│

NI

│

CY

SFS 120 A1

The warranty does not apply if the product has been damaged, improperly used

or improperly maintained. The directions in the operating instructions for the product

regarding proper use of the product are to be strictly followed. Uses and actions

that are discouraged in the operating instructions or which are warned against

must be avoided.

This product is intended solely for private use and not for commercial purposes.

The warranty shall be deemed void in cases of misuse or improper handling, use

of force and modiﬁcations / repairs which have not been carried out by one of

our authorised Service centres.

Warranty claim procedure

To ensure quick processing of your case, please observe the following instructions:

■ Please have the till receipt and the item number (e.g. IAN 12345) available

as proof of purchase.

■ You will ﬁnd the item number on the type plate, an engraving on the front

page of the instructions (bottom left), or as a sticker on the rear or bottom of

the appliance.

■ If functional or other defects occur, please contact the service department

listed either by telephone or by e-mail.

■ You can return a defective product to us free of charge to the service address

that will be provided to you. Ensure that you enclose the proof of purchase

(till receipt) and information about what the defect is and when it occurred.

You can download these instructions along with many other manuals,

product videos and software on www.lidl-service.com.

GB

│

IE

│

NI

│

CY

│

15 ■

SFS 120 A1

Service

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: k[email protected]

Service Ireland

Tel.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (oﬀ peak))

E-Mail: k[email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: k[email protected]

IAN 288381

Importer

Please note that the following address is not the service address. Please use the

service address provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

DE - 44867 BOCHUM

GERMANY

www.kompernass.com

■ 16

│

GB

│

IE

│

NI

│

CY

SFS 120 A1

Ordering replacement parts

You can order the following replacement parts for the product SFS 120 A1:

► 3-piece set of tubular ﬁlm rolls,

narrow (20 x 300 cm)

► 2-piece set of tubular ﬁlm rolls,

wide (28 x 300 cm)

Order the replacement parts via the service hotline (see section “Service”) or

simply visit our website at www.kompernass.com.

NOTE

► Have the IAN number of the appliance ready (can be found on the cover

of these operating instructions) when you place your order.

GR

│

CY

│

17 ■

SFS 120 A1

Περιεχόμενα

Εισαγωγή ....................................................18

Πνευματικά δικαιώματα ................................................... 18

Περιορισμός ευθύνης .................................................... 18

Προβλεπόμενη χρήση ..........................................18

Παραδοτέος εξοπλισμός και έλεγχος μεταφοράς ....................19

Αποσυσκευασία ......................................................... 19

Απόρριψη της συσκευασίας ............................................... 19

Περιγραφή συσκευής ..........................................20

Τεχνικά χαρακτηριστικά ........................................20

Υποδείξεις ασφαλείας ..........................................21

Τοποθέτηση και σύνδεση .......................................23

Απαιτήσεις για το χώρο τοποθέτησης ........................................ 23

Ηλεκτρική σύνδεση ...................................................... 23

Συγκόλληση σωληνωτής μεμβράνης ..............................23

Δημιουργία κενού στη σωληνωτή μεμβράνη .......................26

Καθαρισμός ..................................................28

Καθαρισμός συσκευής ................................................... 28

Αποθήκευση .................................................29

Απόρριψη ...................................................29

Εγγύηση της Kompernass Handels GmbH .........................30

Σέρβις ................................................................ 31

Εισαγωγέας ............................................................ 31

Παραγγελία ανταλλακτικών ....................................32

Seite laden ...

Silvercrest SFS 120 A1 Operating Instructions Manual

Silvercrest SFS 120 A1 Operating Instructions Manual

in anderen Sprachen

Verwandte Papiere