H3C S5120-EI Series Installation, Quick Start

H3C S5120-EI Series Ethernet Switches

Installation Quick Start

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Document Version: 6PW103-20110321

and its licensors

No part of this manual may be reproduced or transmitted in any form

or by any means without prior written consent of Hangzhou H3C

Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, ,

IRF, NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine,

SecPath, Comware, Secware, Storware, NQA, VVG, V

2

G, V

n

G,

PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are

trademarks of Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the

property of their respective owners.

Notice

The information in this document is subject to change without notice.

Every effort has been made in the preparation of this document to

ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of

any kind, express or implied.

Environmental Protection

This product has been designed to comply with the requirements on

environmental protection. For the proper storage, use and disposal of

this product, national laws and regulations must be observed.

Preface

This Installation Quick Start provides steps for basic installation for

the S5120-EI series switches. Further information, such as optional

installation and configuration procedures are available in the

Installation Manual.

This preface includes:

z Audience

z Conventions

z Obtaining Documentation

z Technical Support

z Documentation Feedback

Audience

This documentation is intended for:

z Network planners

z Field technical support and servicing engineers

z Network administrators working with the S5120-EI series

Conventions

This section describes the conventions used in this documentation

set.

Convention Description

Means reader be extremely careful. Improper

operation may cause bodily injury.

Means reader be careful. Improper operation may

cause data loss or damage to equipment.

Means a complementary description.

Obtaining Documentation

You can access the most up-to-date H3C product documentation on

the World Wide Web at

http://www.h3c.com.

Click the links on the top navigation bar to obtain different categories

of product documentation:

[Technical Support & Documents > Technical Documents] – Provides

hardware installation, software upgrading, and software feature

configuration and maintenance documentation.

[Products & Solutions] – Provides information about products and

technologies, as well as solutions.

[Technical Support & Documents > Software Download] – Provides

the documentation released with the software version.

Technical Support

customer_service@h3c.com

http://www.h3c.com

Documentation Feedback

You can e-mail your comments about product documentation to

[email protected].

We appreciate your comments.

i

Table of Contents

1 Prepare for installation.........................................................................1-1

Safety recommendations ...................................................................1-1

Examine the installation site...............................................................1-1

Installation accessories ......................................................................1-2

Installation tools..................................................................................1-2

2 Install the switch...................................................................................2-1

Inspect the switch...............................................................................2-1

Mounting the switch to a rack.............................................................2-1

Mounting the switch on a workbench.................................................2-3

Connecting the grounding cable ........................................................2-4

Connecting the power cable...............................................................2-5

Installing the interface card ................................................................2-6

3 Appendix Compliance and safety information..................................3-1

Regulatory Compliance Information...................................................3-1

Regulatory compliance standards ..............................................3-1

European Directives compliance................................................3-2

USA regulatory compliance ........................................................3-2

Canada regulatory compliance...................................................3-3

Japan regulatory compliance......................................................3-3

CISPR 22 compliance ................................................................3-4

产品符合CLASS A声明...............................................................3-4

Safety Information Sicherheits informationen安全信息......................3-4

Overview Überblick 概述 ............................................................3-4

Electricity Safety Elektrische Sicherheit 用电安全....................3-11

Laser Laser激光辐射 ................................................................3-16

1-1

1 Prepare for installation

Safety recommendations

To avoid possible bodily injury and equipment damage, read the

following safety recommendations before installing an H3C S5120-EI

series. Note that the recommendations do not cover every possible

hazardous condition.

z Turn off all power and remove all the power cables before

opening the chassis. Before cleaning, unplug the power plug first

and do not clean with a wet cloth or liquid.

z Keep the chassis clean and dust-free and away from water or a

damp environment; do not place on an unstable case or desk.

z Ensure proper ventilation of the equipment room and keep the

ventilation vents of the switch free of obstruction.

z Make sure that the operating voltage is the same as labeled on

the switch.

z When replacing interface modules, wear ESD-preventive gloves

to avoid damaging the cards.

For more compliance and safety information, see “Appendix

Compliance and safety information

”.

Examine the installation site

The H3C S5120-EI series can only be used indoors. Make sure that

the floor can support the weight of the cabinet and the switch chassis.

1-2

To ensure the normal operation of the switch, ensure that the

following elements meet requirements described in “Preparing for

installation” in the S5120-EI Installation Manual: temperature/

humidity, cleanness, electromagnetic susceptibility and laser safety.

Installation accessories

Figure 1-1 Installation accessories

Installation tools

The following tools are required for installation; they are not shipped

with the S5120-EI series. Please prepare them by yourself.

Figure 1-2 Installation tools

2-1

2 Install the switch

This guide provides basic installation steps. See the S5120-EI

Installation Manual for comprehensive procedures for installing the

switch.

Inspect the switch

Follow these steps before installing an S5120-EI switch:

z Make sure that you have read “Prepare for installation” carefully

and that the installation site meets all the requirements.

z Using the packing list that was supplied with your switch, inspect

the switch to be sure that you have all the items listed in the

packing list, and verify that the switch was not damaged during

shipment. If anything is damaged or missing, contact your H3C

customer representative.

Mounting the switch to a rack

Table 2-1 Installation methods

The depth of a switch

Installation method

300 mm

(11.81 in.)

420 mm

(16.54 in.)

Using only front mounting brackets √ —

Using front and rear mounting brackets — √

Before installation, wear an ESD-preventive wrist strap, and make

sure that the wrist strap has a good skin contact and is well grounded.

2-2

Figure 2-1 Using only front mounting brackets

Figure 2-2 Using front and rear mounting brackets

2-3

There are three positions to mount a load-bearing screw on both

sides of a switch. You should select a proper position according to the

actual requirements. The rear mounting brackets tightly contacted

with the load-bearing screws can support the switch.

Mounting the switch on a workbench

In many cases, standard 19-inch racks are not available. Therefore,

switches are often placed on clean workbenches. To place your

switch on a workbench, you simply need to:

z Make sure that the workbench is clean, flat, and sturdy.

z Make sure that the environment is well ventilated and allows 10

cm (3.94 in.) of space around the chassis for heat dissipation.

z Do not place heavy objects on your switch.

z The vertical distance between two switches must be at least 1.5

cm (0.59 in).

Figure 2-3 Mounting the switch on a workbench

2

Stick the rubber pads to the

appropriate positions on

the switch bottom

1

2-4

Connecting the grounding cable

Figure 2-4 Connecting the grounding cable

z Use the PGND cable provided with the switch to connect the

grounding strip in the equipment room. Otherwise, the grounding

effect may not be ensured, which easily causes damage to the

switch.

z If no grounding strip is available, see S5120-EI Installation

Manual for detailed grounding methods.

2-5

Connecting the power cable

z Before connecting the power cable, connect the grounding cable

and make sure that the switch is correctly grounded.

z Connect the power cable to the switch first and then to the power

supply system to avoid bodily injury.

z You can use only the RPS power supply recommended by H3C

(optional RPS power supply and power cable) for RPS input.

Figure 2-5 Connect the AC power cable

Install the bail latch

1

2

3

Connect the power cable to

the receptacle

Secure the bail

latch over the

power cable

2-6

Figure 2-6 Connect the DC (RPS) power cable

Installing the interface card

Figure 2-7 Installing the interface card

Remove a blank panel

1

2

Installing the interface

card

2-7

z Do not touch the electronic components on an interface card to

avoid damaging the interface card.

z After removing an interface card, install a blank panel to the

empty slot to prevent dust from entering the switch.

z If there is a ”DO NOT REMOVE” label on the rear panel, the

switch does not support interface cards. Do not remove the blank

panel that has the label on it.

3-1

3 Appendix Compliance and safety

information

Regulatory Compliance Information

Regulatory compliance standards

Table 3-1 Regulatory compliance standards

Discipline Standards

EMC

FCC Part 15 (CFR 47) CLASS A

ICES-003 CLASS A

VCCI-3 CLASS A

VCCI-4 CLASS A

CISPR 22 CLASS A

EN 55022 CLASS A

AS/NZS CISPR22 CLASS A

CISPR 24

EN 55024

EN 61000-3-2

EN 61000-3-3

EN 61000-6-1

ETSI EN 300 386

GB 9254

YD/T993

Safety

UL 60950-1

CAN/CSA C22.2 No 60950-1

IEC 60950-1

EN 60950-1/A11

AS/NZS 60950-1

EN 60825-1

EN 60825-2

FDA 21 CFR Subchapter J

GB 4943

3-2

European Directives compliance

LVD/EMC Directive

S5120-EI SERIES products comply with the European Low Voltage

Directive 2006/95/EC and EMC Directive 2004/108/EC.

A copy of the signed Declaration of Conformity can be downloaded

from:

http://www.h3c.com/portal/Technical_Documents.

WEEE Directive–2002/96/EC

The products this manual refers to are covered by the Waste

Electrical & Electronic Equipment (WEEE) Directive and must be

disposed of in a responsible manner.

USA regulatory compliance

FCC Part 15

S5120-EI SERIES comply with Part 15 of the FCC Rules. Operation

is subject to the following two conditions:

z This device may not cause harmful interference.

z This device must accept any interference received, including

interference that may cause undesired operation.

If the customer modifies the equipment without the authorization of

H3C, which directly or indirectly contribute to the equipment

incompliance with FCC requirements for Class A digital devices, H3C

3-3

is not liable for such interference problem and the expenses incurred

therefrom shall be covered by the customers.

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

FDA

S5120-EI SERIES Conform to the applicable requirements of 21 CFR

Subchapter J

Canada regulatory compliance

ICES-003

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme

NMB-003 du Canada.

Japan regulatory compliance

VCCI

S5120-EI SERIES comply with the requirements of VCCI Class A

Information Technology Equipment (ITE).

Warning: If this equipment is used in a domestic environment, radio

disturbance may arise. When such trouble occurs, the user may be

required to take corrective actions.

3-4

CISPR 22 compliance

S5120-EI SERIES comply with the requirements of CISPR 22 for

Class A Information Technology Equipment (ITE).

Warning: If this equipment is used in a domestic environment, radio

disturbance may arise. When such trouble occurs, the user may be

required to take corrective actions.

产品符合 CLASS A 声明

此为 A 级产品，在生活环境中，该产品可能会造成无线电干扰。在这

种情况下，可能需要用户对其干扰采取切实可行的措施。

Safety Information Sicherheits informationen安全

信息

Overview Überblick 概述

This section introduces part of the safety precautions that should be

followed during the installation and maintenance of the equipment.

And for the safety statements and warnings, there followed the

translations of both German and Chinese to comply with the national

requirements.

Dieser Abschnitt macht Sie mit den Sicherheitsvorschriften vertraut,

die Sie bei der Installation und Instandhaltung der Ausrüstung

beachten müssen.

本章节介绍了在安装、日常维护本系列设备时，必须遵循的安全预防

规范。

3-5

z Before any operation is performed, please read the operation

instructions and precautions carefully to minimize the possibility

of accidents. The Note, Caution, Warning and Danger items in

other manuals do not cover all safety precautions that should be

followed. They are only the supplements to the safety

precautions for operations as a whole. Therefore, the personnel

in charge of the installation and maintenance of the products are

required to understand these basics of safety operation.

z In performing various operations, please follow the local safety

regulations. The safety precautions introduced in the product

manuals are supplementary and subject to the local safety

regulations.

z When various operations are executed on the products, the

precautions and special safety instructions provided with the

products must be followed to the full.

z The personnel in charge of the installation and maintenance of

the products must be trained as professionals to master the

proper operating methods and all safety precautions. Only the

trained and qualified personnel can perform operations such as

equipment installation and maintenance.

3-6

z Lesen Sie bitte alle Arbeitsanweisungen und

Sicherheitvorschriften sorgfältig durch, bevor Sie mit dem

Arbeiten beginnen. Nur durch Beachtung dieser Hinweise lässt

sich das Unfallrisiko minimieren. Die in anderen Handbüchern

aufgeführten Symbole Anmerkung, Achtung, Warnung und

Gefahr beinhalten nicht alle zu beachtenden

Sicherheitvorschriften. Sie dienen lediglich der Ergänzung.

Deshalb muss sich das für die Installation und Instandhaltung

der Ausrüstung verantwortliche Personal mit allen

Sicherheitshinweise vertraut machen.

z Bei der Durchführung der verschiedenen Arbeitsschritte müssen

außerdem die örtlichen Sicherheitsvorschriften beachtet werden.

Die in den Handbüchern der einzelnen Produkte aufgeführten

Sicherheitshinweise sind Ergänzungen und unterliegen den

nationalen Sicherheitsvorschriften.

z Während der Arbeit mit den Produkten sind deshalb

grundsätzlich alle Sicherheitsvorschriften und spezifischen

Sicherheitshinweise genau zu beachten.

z Das für die Installation und Instandhaltung der Produkte

verantwortliche Pesonal muss geschult werden, um alle

Sicherheitsvorschriften zu kennen und die richtigen

Arbeitsmethoden anwenden zu können. Nur geschultes und

qualifiziertes Personal kann die Installation und Instandhaltung in

korrekter Weise durchführen.

Seite laden ...

H3C S5120-EI Series Installation, Quick Start

H3C S5120-EI Series Installation, Quick Start

in anderen Sprachen

Verwandte Papiere

Sonstige Unterlagen