1
Page 2-16
Installation Manual
IP Access Control Device
A1121 Series
Seite 17-32
Installationsanleitung
IP Zutrittskontrollgerät
A1121 Serie
VERSION ., MIN. HW .
A1121
Page 33-48
Manuel d‘installation
Système de contrôle
d‘accès IP
Série A1121
Páginas 49-63
Manual de instalación
Sistema de control
de acceso IP
Serie A1121
2
INSTALLATION MANUAL
Read these instructions carefully before starting to use
any components. Keep the manual so you can refer
to it at a later date if required. If you hand over the
device to other persons for use, please hand over the
operating manual as well.
You can always find the most up-to-date version of the
installation manual on www.doorbird.com/support
To make things easier we use the term “device” for the
product “IP Access Control Device A1121” and “mobile
device” for a smartphone or tablet.
Liability
Every care has been taken in the preparation of this
document. Please inform Bird Home Automation
GmbH of any inaccuracies or omissions. Bird Home
Automation GmbH cannot be held responsible for any
technical or typographical errors and reserves the right
to make changes to the product and manuals without
prior notice. Bird Home Automation GmbH makes
no warranty of any kind with regard to the content
of this document, including, but not limited to, the
implied warranties of merchantability and fitness for
a particular purpose. Bird Home Automation GmbH
shall neither be liable nor responsible for incidental
or consequential damages in connection with the
furnishing, performance or use of this material. This
product is only to be used for its intended purpose.
Equipment Modifications
This equipment must be installed and used in
strict accordance with the instructions given in
the user documentation. This equipment contains
no components that require service by the user.
Unauthorized equipment changes or modifications
will invalidate all applicable regulatory certifications
and approvals.
Symbols used
Danger: Indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
Warning: Indicates a hazardous situation
which, if not avoided, could result in death or
serious injury.
Caution: Indicates a hazardous situation
which, if not avoided, could result in minor or
moderate injury.
NOTICE Notice: Indicates a situation which, if not
avoided, could result in damage to property.
Important: Indicates significant information
which is essential for the product to function
correctly.
Note: Indicates useful information which
helps in getting the most out of the product.
• Mounting, installation and servicing work on
electrical devices may only be performed by
a qualified eletrician. Failure to observe this
regulation could result in the risk of serious
damage to health or fatal injury due to electric
shocks.
• Devices with 110-240 V connection: The device
may only be connected to an easily accessible
power socket outlet. The mains adapter must be
pulled out if a hazard occurs.
• For power supply, only use the original plug-
in mains adapter delivered with the device,
separately available DIN rail power supplies or
a recommended PoE-Switch/PoE-Injector as
specified in this manual.
• Because of electrostatic charging, direct contact
with the circuit board can result in destruction
of the device. Direct contact with the circuit
board must therefore be avoided at any time.
• Observe the EN 60065 resp. EN 60950 resp. EN
62368 standard.
• Do not use the device if there are signs of
damage to the housing, control elements
or connecting sockets, for example, or if it
demonstrates a malfunction. If you have any
doubts, please have the device checked by an
authorized expert.
• Do not open the device. This voids the warranty
of the device. The device does not contain any
parts that can be maintained by the user. In
the event of an error, please have the device
checked by an authorized expert.
• For safety, approval and licensing reasons (CE/
FCC/IC etc.), unauthorized change and/or
modification of the device is not permitted.
• The device is not a toy: do not allow babies and
children to play with it.
• To avoid the danger of suffocation, keep
any packing materials away from babies
and children. Plastic films/bags, pieces of
polystyrene, etc. are not a toy and can be
dangerous in the hands of a child. Discard any
packing materials immediately after removing
the product. Do not reuse packing materials.
• Always lay cables in such a way that they do not
become a risk to people and domestic animals.
• Voltage is applied to parts within the
equipment. Do not touch any parts that are
not associated with the installation, wiring, or
connection. Electric shock could result.
• On devices which are not marked as weather-
proof: Keep the device away from water or any
other liquid.
Hazard information
WARNING
ENGLISH
3
• Do not install or make any wire terminations
while power supply is plugged in. It can cause
eletric shock or damage to the device.
• Before turning on power, make sure wires are
not crossed or shorted. If not, fire or eletric
shock could result.
• High voltage may be present internally. Do not
open the device. Electric shock could result.
• The device is not of explosion-proof. Do
not install or use near gases or flammable
materials. Fire or explosion could result.
• Do not install two power supplies in parallel
to a single input. Fire or damage to the device
could result. Be sure to connect a single power
supply to the device.
• Do not connect any terminal on the device to
an AC power line. Fire or electric shock could
result.
• Keep AC cord from being marred or crushed.
If the AC cord is fractured, fire or electric shock
could result.
• Do not plug or unplug with wet hands. Electric
shock could result.
• Do not put any metal or flammable material
into the device. Fire, electric shock, or device
trouble could result.
• Existing wiring may contain high voltage AC
electricity. Damage to the device or electric
shock could result. Wiring and installation
must be done by a qualified eletrician.
• When mounting the device on a wall or
ceiling, install the device in a convenient
location, but not where it could be jarred or
bumped. Injury could result.
• On devices with ground terminals, connect to
an earth ground. Otherwise fire or malfunction
could result.
• On devices with plastic or real glass, do not put
high pressure on the glass. If fractured, injury
could result.
• On devices with LCD, if LCD is punctured, do
not allow contact with the liquid crystal inside.
Injury could result. If necessary, gargle your
mouth and clean your eyes or skin with clear
water for at least 15 minutes and consult your
doctor.
• Do not put anything on the device or cover
the device with cloth, silicone, glue, coating,
separate covering etc. Fire or device issues
could result.
• Do not install the device in any of the following
locations. Fire, electric shock, or device trouble
could result.
Places under direct sunlight or places near
heating equipment that varies in temperature.
Places subject to dust, oil, chemicals, hydrogen
sulfide (hot spring).
Places subject to moisture and humidity
extremes, such as bathrooms, cellars,
greenhouses, etc.
Places where the temperature is very low, such
as inside a refrigerated area or in front of an air
conditioner.
Places subject to steam or smoke (e.g. near
heating or cooking surfaces).
Where noise generating devices such as
dimmer switches or inverter electrical
appliances are closeby.
Locations subject to frequent vibration or
impact.
• On devices with intercom, be sure to perform
a call test with low audio volume on both
intercom devices. A sudden call etc. may arrive
causing for example damage to your ear.
• If the device does not operate properly, unplug
the power supply.
• All devices which are not marked as weather-
proof are designed for indoor use only. Do not
use outdoor.
• On devices which are marked weather-proof:
Do not spray with high-pressure water. Device
issues could result.
• We do not assume any liability for damage to
property or personal injury caused by improper
use or the failure to observe the hazard
information. In such cases, any claim under
warranty ceases. For consequential damages,
we assume no liability!
WARNING
Safety instructions
• The device shall be used in compliance with
local laws and regulations.
• Store the device in a dry and ventilated
environment.
• Avoid exposing the device to shocks or heavy
pressure.
• Do not install the device on unstable brackets,
surfaces or walls. Make sure the material is
strong enough to support the weight of the
device.
• Use only applicable tools when installing the
device. Using excessive force with tools could
cause damage to the device.
• Do not use chemicals, caustic agents, or
aerosol cleaners.
• Use a clean dry cloth for cleaning.
NOTICE
4
• Use only accessories that comply with
technical specification of the device. These can
be provided by Bird Home Automation GmbH.
• Use only spare parts provided by or
recommended by Bird Home Automation
GmbH.
• Do not attempt to repair the device by yourself.
Contact Bird Home Automation GmbH for
service matters.
• Keep the device more than 1 m (3.3‘) away
from microwave, radio, TV, wireless router and
any other wireless devices.
• On devices with intercom or built-in speaker
or built-in microphone or signal transmission
functions, keep the wires more than 30 cm
(12‘‘) away from AC 100-240 V wiring. AC
induced noise and/or device malfunction
could result.
• Install the device in an area that will be
accessible for future inspections, repairs and
maintenance.
• If the device is used close to a cellular phone, the
device may malfunction.
• The device can be damaged if dropped. Handle
with care.
• The device turns inoperative during power
failure.
• On devices with intercom or built-in speaker or
built-in microphone, in areas where cellular or
Radio / TV broadcasting station antennas are
closeby, the device may be affected by radio
frequency interference.
• On devices with LCD screen, it must be noted
in advance that the LCD panel, though
manufactured with very high precision
techniques, inevitably will have a very small
portion of its picture elements always lit or
not lit at all. This is not considered a device
malfunction.
• On devices with intercom, due to the
environmental sound around the device, it
may hinder smooth communication, but this
is not a malfunction.
• On devices with Username/Password, the
Username/Password to access the device is the
customer‘s responsibility. Make sure to use a
password that cannot be easily guessed by a
third party. We recommend that you change
the Password on a regular basis.
• We will, under no circumstances, be liable
for damage that occurs due to failures in
power supply, network equipment or terminal
devices; failures due to Internet providers
and cellular network providers; failures such
as disconnected lines and other losses in
communication, which makes it impossible to
provide this service as well as in any way delay
this service due to any other causes outside of
our responsibility; or if an error or missing data
occurs during transmission.
Transportation
NOTICE When transporting the device, use the original
packaging or equivalent to prevent damage
to the device.
Warranty Information
For information about the device warranty, see
www.doorbird.com/warranty
Information on disposal for users of waste
electrical & electronic equipment (private
household)
This symbol on the products and/or accompanying
documents means that used electrical and electronic
products should not be mixed with general household
waste. For proper treatment, recovery and recycling,
please take these products to designated collection
points, where they will be accepted an a free of charge
basis. Alternatively, in some countries you may be able
to return your products to your local retailer upon the
purchase of an equivalent new product. Disposing
of this product correctly will help to save valuable
resources and prevent any potential negative effects
on human health and the environment which could
otherwise arise from inappropriate waste handling.
Please contact your local authority for further details
of your nearest designated collection point. Penalties
may be applicable for incorrect disposal of this waste,
in accordance with national legislation.
Information on disposal in other countries outside
the European Union
This symbol is only valid in the European Union. If you
wish to discard this product, please contact your local
authorities or dealer and ask for the correct method
of disposal.
ENGLISH
5
COMPONENTS*
1x Quickstart guide
with Digital Passport
1x Drilling template
1x Disassembly tool for
screw connection terminal
plug
1x Power supply unit (mains adapter)
with four country-specific adapters
Small parts
1x Installation manual
1x Flush-mounting
housing
(flush-mounted model)
1x Main Electrical Unit
with front panel
1x Wall-mounting bracket
(surface-mounted model)
THIS SIDE UP
* The sketches in this manual may differ from the purchased model.
1) Keypad wit 12 keys
2) Dual frequency RFID reader (125 KHz, 13.56 MHz)
3) Bluetooth transceiver
4) Status icons with Diagnostic LEDs
5) Security screw
6) Wiegand jack
7) Screw connection terminal
8) SETUP Button (SET) of the device to e.g.
configure the WiFi interface of the device using
the DoorBird App
The flush-mounted model may differ optically.
DEVICE
Front Back
2
1
4
5
3
1x RJ45 adapter
WIFI
67
8
6
VIDEOS
Need help with the installation? Be sure to watch our
installation videos which can be found on
http://www.doorbird.com/support
Each individual step of the installation is clearly
documented in the videos.
INSTALLATION
All the steps below should be carried out carefully
by a competent adult, taking into consideration
any applicable safety regulations. Please contact us
directly or seek the advice of a competent specialist.
Please ensure that all wires used for the
installation are undamaged along their entire
length and approved for this type of use.
Network speed and network components
Please ensure that the upload speed of your Internet
connection is at least 0.5 Mbps. The user experience is
only as good as your network speed, network stability
and quality of your network components, such as
your Internet Router and WiFi access points or WiFi
repeaters. Please also make sure that your network
components are no older than two years old, have
been manufactured by a well-known manufacturer,
and have the latest firmware installed.
Should these requirements not be fulfilled, it may
occur that push notifications are delayed or not
delivered to your mobile device.
Requirements:
High-speed Internet (via landline): DSL, cable or optical
fibre
Network: Ethernet, with DHCP
SWITCHING OFF POWER
Switch off the power to all wires leading to
the assembly location, e.g. power supply for
the device or an electrical door opener.
DISMANTLING THE EXISTING
ACCESS CONTROL DEVICE
Should there already be an access control device on
the exterior wall of the house, please remove it.
DETERMINING THE ASSEMBLY
LOCATION
NOTICE Do not expose the device to direct sunlight.
The housing temperature can exceed the
maximum allowed temperature limit. This
can result in damage of electric and
mechanic components of the device and
injuries especially when touching exterior
parts of the device. White and bright
silver-colored front plates absorb less
sunlight than dark ones.
Any defects caused by direct sunlight are not
covered by warranty.
Important note for cavity mounting (e.g. in
pedestals and mailboxes):
To protect the electronic units, please
ensure that the technical components are
protected against dripping and running
water caused by condensate or entering
the mounting space through openings.
To protect the electronic units, ensure
that the mounting space inside is not
accumulating water.
Sucient air circulation must be ensured,
as well as unobstructed drainage of water
at the base of the installation.
Failure to do so will result in warranty being
declined.
ENGLISH
7
15 cm
5.91 in
8,5 cm
3.35 in
ASSEMBLING THE MOUNTING HOUSING
The product is available as a surface-mounted, flush-mounted and retrofit version. In the flush-mounted
version, the front panel is slightly larger to better cover the hole in the wall, and the mounting housing
(backbox) is made entirely of metal instead of plastic.
In the retrofit version, the front panel is slightly larger to better cover the hole in the existing panel and the
mounting is not realized with a separate mounting housing (backbox) but with metal clamps.
68,00 mm
2.68 in
138,00 mm
5.43 in
26,50 mm
1.04 in
68,00 mm
2.68 in
138,00 mm
5.43 in
26,50 mm
1.04 in
If the wall of the house is not made of wood, you
should drill dowel holes 5 mm (0.19 in) in diameter
in the wall according to the drilling template and
then place the dowels provided into the boreholes.
If you must drill holes in a wall, insert screws into a wall or lever up a wall, ensure that no cables or mains
(gas, water, etc.) are to be found in the wall.
If the wall of the house is made of wood, dowels are not normally required. There are special dowels for
assembling the device on an insulating wall, e.g. Fischer insulating dowels.
If you use the retrofit version, cut an appropriate
hole in the existing panel.
If you use the flush-mounted housing, lever up the
wall accordingly.
Flush-mounted model Retrofit model
8
THIS SIDE UP
. MOUNTING
Lead all cables and wires you want to connect to the device through the mounting housing (for retrofit version:
through the hole in the existing panel).
. DISASSEMBLING THE FRONT PANEL
(APPLIES ONLY TO THE SURFACE-MOUNTED AND FLUSH-MOUNTED MODEL)
Remove the front panel with the attached Main Electrical Unit carefully from the mounting housing (backbox)
using the orange (Torx+Pin) screw driver provided.
We have designed the front panel and the safety screw in a way that it cannot be screwed through the
front panel so that is does not fall off / get lost during installation..
Turn the safety screw counter-clockwise until it is loose. Pull the front panel with attached Main
Electrical Unit out of the mounting housing (backbox).
Flush-mounted model Surface-mounted model
Please make sure that the outer frame of the flush-
mounted housing rests on the outside of the wall
and that the edge of the flush-mounted housing
is sealed all around against moisture from the
outside.
Before mounting: Pierce through the middle
of the rubber seal for the cable entry using a
screwdriver.
THIS SIDE UP
Retro Fit model
Surface-mounted modelFlush-mounted model
ENGLISH
9
NETWORK CONNECTION OPTIONS
You can connect the device to the network by either using a WiFi 2.4 GHz
connection or a network cable.
OPTION
Network cable (recommended, maintenance free)
Install a network cable (which is plugged into a network switch / router
with Internet access) from the inside of your building to the assembly
location. The network cable between the assembly location and the
network switch / router can have a maximum length of 80 m/262 ft (IEEE
802.3). If you must span a distance of more than 80 meters/262 feet you
can put a network switch in between. Make sure to use a high-quality
Cat.5 network cable or better and with proper shielding (Screened Foiled
Twisted Pair (S/FTP or SFTP)) whereby the shield is connected to the outer
metal shield of the RJ45 plug (8P8C).
The device itself does not have an RJ45 socket. The scope of delivery
includes an RJ45 adapter that can be routed out of the housing. As an
alternative, the RJ45 connector of the network cable can be removed
on the device side to connect the wires directly to the Phoenix strip
according to the assignment under point 7 „CONNECTING THE DEVICE“.
OPTION
WiFI 2.4 GHz
When using WiFi please make sure you have a good WiFi signal at the
assembly location of the device. You can increase the WiFi signal by using
so called “WiFi repeaters”, which can boost your WiFi signal. You should
install such a WiFi repeater close to the assembly location of the device,
typically inside your home and close to the device.
For further information regarding WiFi installations, please visit
www.doorbird.com/wifi
PREPARE POWER SUPPLY
The device does not have a battery as power supply, therefore, choose one
of the following options.
OPTION
Power supply using the power supply unit (mains adapter)
To power the device using the provided mains adapter, 2 insulated wires
are required. The power supply unit has a 300 cm (9.8 ft) long cable with
two insulated wires. The network connection is then established via a
network cable or alternatively via WiFi.
NOTICE Do not plug the power supply unit into the wall socket yet.
Only use the power supply unit provided along with the device,
or a DIN-rail power supply unit (see “OPTION 3”) that you
can obtain from us separately, since this has been specially
stabilized electrically and is equipped with an integrated audio
interference reduction device. Other power supply units may
destroy the device or cause poor transmission quality. The
warranty automatically expires if you use a different power
supply unit.
The provided mains adapter is only
capable to power one device. It is not
designed to power multiple devices
simultanously.
If you must power more than one device
with one power supply, we recommend
to use a PoE-Switch with PoE Standard
IEEE 802.3af Mode A or an appropriate
DIN rail power supply (see “OPTION 3”).
If you have only two wires available at
the assembly location, you may use the
“DoorBird 2-Wire Ethernet PoE Converter
A1071”, sold separately. It allows you to
transfer network data (Ethernet) and
power (PoE) with a simple two-wire
cable over long distances. For example,
existing buildings with a simple two-wire
bell wire can be equipped with network
technology without having to retrofit any
network cables.
For reasons of network stability, we
principally recommend using a network
cable, as WiFi is sensitive to interference
(range, house walls acting as shields, re-
liability of performance, third party WiFi
networks, wireless transmitters causing
interference in the area, etc.).
10
NOTICE The power supply unit is plugged into a wall socket, usually
where the two wires from your assembly location come out of
the wall in the interior of the house.
The provided mains adapter is not outdoor-ready and for
indoor-use only.
OPTION
Power supply and network connection using PoE (Power over
Ethernet)
To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-
Injector (e.g. DoorBird Gigabit PoE Injector A1093), use a CAT.5 cable or
higher in accordance with the PoE standard IEEE 802.3af Mode A.
A CAT.5 cable or higher must be used for this purpose, as network signals
can only be transmitted over completely insulated, shielded and twisted
cables. If you use PoE as a source of power, the four wires for PoE then
simultaneously form the data line. The device will not start if your PoE-
Switch/PoE-Injector does not support the PoE Standard IEEE 802.3af
Mode A.
NOTICE Do not combine the power supply from the power supply unit
(mains adapter) with the power supply via PoE.
You can find further information about PoE here:
http://www.doorbird.com/poe
1. Disconnect the PoE-Switch or PoE-Injector from the power grid.
2. Place the network cable in the installation site of the device.
If you must power more than one device
with one power supply , we recommend
to use a PoE-Switch with PoE Standard
IEEE 802.3af Mode A or an appropriate
DIN rail power supply (see “OPTION 3”).
Theoretically (not recommended by us!),
an unshielded, but over the whole length
(max. 80 m/262 ft) twisted bell wire with
two pairs of wires (first twisted pair of
wires: “T+, T-”, second twisted pair of wi-
res “R+, R-”) can be used for the network
and PoE transmission as an alternative
to a Cat.5 network cable or better. This is
comparable to a Cat.3 network cable. In
this case, however, we cannot guarantee
the data throughput or the stability of
the network connection and power sup-
ply; this must be measured and checked
on site by qualified personnel over several
hours (network data is transmitted at
high frequency, therefore a shielded
Cat.5 network cable twisted in pairs or
better must normally be used).
For easier installation we strongly
recommend to remove the plug from
screw connection terminal while you
connect the cables and wires.
CONNECTING THE DEVICE
It is possible to connect the cables and wires to the device conveniently
and safely via the labeled screw connection terminal. You can connect all
necessary cables and wires to the device now.
NOTICE Please remove any cables and wires from the connection ports
of the device that you do not need.
The product comes with a disassembly tool that
allows you to safely remove the connector from the
screw terminal socket. Please do not use any other
tool, e.g. a screwdriver, as this may damage the
circuit board of the device.
OPTION
Power supply using a DIN rail power supply unit
Alternatively to the mains adapter, we offer DIN rail power supplies in
our online shop, which can be installed by a specialist. The network
connection is then made via a network cable or alternatively via WiFi.
ENGLISH
11
LAN / POE
D D GND
Wiegand
R R R R VDC
– +
Port Description
LAN/POE
T+ T- R+ R-
The device does not have an integrated standarized RJ45 socket to ensure ...
• that the device rests as flat as possible on the wall.
• that no wall needs to be levered up.
• that a strong and inflexible Cat.6 or Cat.7 installation cable can be used.
Use only four wires (1, 2, 3 and 6) of a standard Network cable Cat.5 or better,
coming from the Internet Router/PoE-Switch/PoE-Injector.
Cat.5 / Cat.6 Network cable
T+ White and orange network cable wire (Number 1, Transmit Data +)
T - Orange network cable wire (Number 2, Transmit Data -)
R+ White and green network cable wire (Number 3, Receive Data +)
R - Green network cable wire (Number 6, Receive Data -)
Cat.7 Network cable (Installation cable)
T+ White network cable wire from pair “orange/white”
(Number 1, Transmit Data +)
T- Orange network cable wire from pair “orange/white”
(Number 2, Transmit Data -)
R+ White network cable wire from pair “green/white”
(Number 3, Receive Data +)
R- Green network cable wire from pair “green/white”
(Number 6, Receive Data -)
NOTICE Do not power the device simultaneously via the power supply from
the power supply unit (mains adapter) and the power supply via PoE.
T+ T- R+ R-
12
R1, R1 Bi-stable latching relay #1, max. 24 V DC/AC, 1 A. Security feature: The relay
keeps its state even in the case of loss of power. You can configure the default
state of the relay (open/close) via the DoorBird App. These ports can be used
to connect e.g. an electric door opener. The device does not supply power to
the connected device. The power supply for the electric door opener must be
installed separately.
When wiring an electric door opener directly to the device. There is a
risk that the electric door opener could be tampered by unauthorized
third parties (e. g. by breaking the device and short-circuiting the
wiring of the door opener). Therefore, we generally recommend the
use of a remote safety relay mounted indoors (e. g. DoorBird I/O Door
Controller A1081) for wiring an electric door opener for a more secure
installation in your home.
R2, R2 Bi-stable latching relay #, max. 24 V DC/AC, 1 A. Security feature: The relay
keeps its state even in the case of loss of power. You can configure the default
state of the relay (open/close) via the DoorBird App. These ports can be used
to connect e.g. an electric door opener. The device does not supply power to
the connected device. The power supply for the electric door opener must be
installed separately.
When wiring an electric door opener directly to the device. There is a
risk that the electric door opener could be tampered by unauthorized
third parties (e. g. by breaking the device and short-circuiting the
wiring of the door opener). Therefore, we generally recommend the
use of a remote safety relay mounted indoors (e. g. DoorBird I/O Door
Controller A1081) for wiring an electric door opener for a more secure
installation in your home.
15 VDC - 15 V DC Power supply input, negative pole (-). Please connect the black wire
of the power supply unit (mains adapter) supplied with this device if you do
not power the device using PoE.
NOTICE Do not power the device simultaneously via the power supply from
the power supply unit (mains adapter) and the power supply via PoE.
15 VDC + 15 V DC Power supply input, positive pole (+). Please connect the red wire of
the power supply unit (mains adapter) supplied with the device here, if you do
not power the device using PoE.
NOTICE Do not power the device simultaneously via the power supply from
the power supply unit (mains adapter) and the power supply via PoE.
D0 Data Low. For Wiegand output (RFID reader, Keypad). Max. 5 mA per output
(data line). Wiegand can be turned on/off and configured via the DoorBird App.
The Small parts bag provided contains a cable with tree individual wires (black,
green, white) and plug. Please use this cable to connect your Wiegand device
(D0: Green wire).
D1 Data High. For Wiegand output (RFID reader, Keypad). Max. 5 mA per output
(data line). Wiegand can be turned on/off and configured via the DoorBird App.
The Small parts bag provided contains a cable with tree individual wires (black,
green, white) and plug. Please use this cable to connect your Wiegand device
(D1: white wire).
GND Ground. For Wiegand output (RFID reader, Keypad). Wiegand can be turned
on/off and configured via the DoorBird App.
The Small parts bag provided contains a cable with tree individual wires
(black, green, white) and plug. Please use this cable to connect your Wiegand
device (GND: Black wire).
R1
R1
R2
R2
ENGLISH
13
NOTICE Please take care when connecting the cables and wires. Connecting the cables and wires the wrong way
may damage the device. Wires without insolation material must not protrude out of the green screw
connection terminal, it may lead to electrical short and damage the device.
ASSEMBLE THE DEVICE TO THE MOUNTNG HOUSING (BACKBOX)
If you use the surface- or flush-mounted version, assemble the front panel with the attached Main Eletrical
Unit carefully using the orange (Torx+Pin) screw driver provided with the wall mounting-bracket / mounting
housing. Turn the safety screw clockwise until it is hand-tight.
NOTICE Tighten the safety screw by hand only (less than 5 newton meter [Nm]), otherwise the Main Eletrical
Unit housing may be damaged.
If you use the retrofit model, assemble the front
panel with the attached Main Eletrical Unit
carefully to the existing panel using the metal
clamps.
Retro Fit model
Surface-mounted modelFlush-mounted model
14
ACTIVATE THE DEVICE
If the device is to be supplied with power by a mains
adapter, plug the power adapter of the device into
a wall socket. If the device is to be powered via PoE,
switch on the PoE-Switch/ PoE-Injector which is
connected to the device. If the device is to be powered
via DIN-rail power supply, switch on the DIN-rail power
supply.
The Keypad LEDs indicate whether the device is
supplied with power. The LEDs light up in white color
a few seconds after you have connected the device to
the power supply.
If Keypad LEDs do not light up, please check the
power supply. When using a wall-plug power
supply and not PoE, please check whether you have
connected the positive pole and negative pole to the
device correctly.
The device is ready for operation (booting up process,
any software updates, etc.) once it has emitted a short
diagnosis sound (two beeps) from the integrated
piezo speaker and the Diagnostic LEDs light up for
a few seconds in blue color. This may last for up to 5
minutes.
DOWNLOADING AND INSTALLING
THE APP
Download the “DoorBird” App by Bird Home
Automation onto your mobile device from the Apple
App Store or Google Play Store. You can always find
the most up-to-date version of the App manual on
www.doorbird.com/support
If you use WiFi for connecting the device to your
Internet Router, first go to the DoorBird App > ”WiFi
Setup“ and follow the instructions.
If you have finished the WiFi setup or have connected
the device to your Internet Router by means of a
network cable, go to the DoorBird App > “Add device”
and click on the QR code icon in the “User” field.
Scan the user QR code found on the “Digital Passport”
provided with the device.
If you have problems adding the device to the App
please check if the device is online ( www.doorbird.
com/checkonline ). If the device is not online, please
check the WiFi or network cable connection again.
DIAGNOSTIC-LEDS
Both LEDs light up blue:
for 5 seconds continuously illuminated
– Device is connected to the internet.
for 30 seconds with flashing intervals of 1 second
– Device has no internet connection.
for 30 seconds with flashing intervals of 3 seconds
– Device has no network connection.
Both LEDs light up yellow:
for 30 seconds with flashing intervals of 1 second
– Device has entered WiFi setup mode
DIAGNOSTIC SOUNDS
The device may emit brief diagnostic sounds after
it has been connected to power supply / network /
Internet, e.g. upon boot process finished, press of a key,
WiFi Setup Mode enabled, RFID Reader detected tag,
Relay triggered.
TAMPER SENSOR
The device has a built-in tamper sensor that can
be configured via the app to send an alert over the
network (e.g. a push notification) if the device is
moved during operation.
BLUETOOTH TRANSCEIVER
The device has a built-in Bluetooth® transceiver.
We will add further functionality for interesting
applications soon. Please check our company news
blog or the latest version of this manual at
www.doorbird.com/support for updates.
DOORBIRD CONNECT
The device features many options to integrate it into
third-party applications. For information, terms and
conditions see www.doorbird.com/connect
ENGLISH
15
MAINTENANCE OF THE FRONT PANEL
Cleaning and maintenance instructions
All of our front panels are made of high-quality
materials and are designed for a durable lifetime.
Since this kind of devices are usually installed in
unprotected outdoor areas, they are exposed to
adverse weather conditions and aggressive substances,
especially close to frequently used roads, in coastal
and industrial areas. Therefore, please consider the
following care instructions. Unfortunately, we cannot
accept any liability for damage if these instructions
are not being observed. Aggressive dirt such as bird
droppings should be removed as quickly as possible.
NOTICE Aggressive stains such as bird droppings
should be removed as soon as possible.
NOTICE Never use abrasive detergents such as steel
wool or scouring milk!
Warm water is usually sucient, if necessary with
a little detergent, a soft cloth or brush. Plastic parts
must not be treated with metal care products.
Remove all residues of cleaning agents or lubricants to
avoid stains or discolouration after the maintenance.
Stainless Steel
Only high-quality stainless steel is used for all available
DoorBird devices. However, high-quality stainless steel
can also rust, as approx. 70% of stainless steel is made
of iron. Rust resistance is only achieved by a protective
layer (also called passive layer), which covers the iron
like a skin. This protective layer consists essentially of
chromium and other precious metals.
Iron particles, grinding dust and chips deposited on
stainless steel can lead to corrosion (rust film). These
iron particles can be found everywhere, but especially
in coastal and industrial areas and close to frequently
used roads. Please remove ferrous deposits immediately,
as they will attack your device and lead to real rust if
not removed. To remove rust, simply wipe off the dust;
in addition, a care product is recommended, e.g. WD
40, available e.g. at Amazon for less than € 5.00. Simply
apply in a thin layer and rub in. The same applies if rust
appears on the engravings on the stainless steel surface.
Cement or lime splashes should be carefully removed
as soon as possible with a wooden spatula before
hardening.
The following cleaning detergents are not to be used
as they reduce corrosion resistance:
• products containing chloride and hydrochloric
acid
• Bleach (in case of accidental use, rinse thoroughly
with water)
• Silver polish
After the cleaning with clear water wipe with damp
cloth and rub dry to avoid lime traces. Lime residues
can be avoided by using demineralised water.
Stainless steel PVD coated
PVD coated, chrome-plated or gold-plated surfaces are
recommended to be cleaned with a grease-
dissolving detergent and clear water or with a clean
and dust-free microfibre cloth. For high-gloss surfaces,
use a scratch-free cloth (e.g. cleaning cloth for glasses,
furniture polishing cloth, etc.).
Lacquered surfaces
Clean painted surfaces and lettering with a soft,
scratch-free cloth moistened with a mild soap solution
(e.g. cleaning cloth for glasses, furniture polishing cloth,
etc.). To prevent stains or discolouration, the detergents
should be wiped off without leaving any residue.
Be particularly careful with lettering in order not to
damage the film or the print.
16
LEGAL NOTES
General remarks
1. DoorBird is a registered trademark of Bird Home Automation
GmbH.
2. Apple, the Apple logo, Mac, Mac OS, Macintosh, iPad, Multi-Touch,
iOS, iPhone and iPod touch are trademarks of Apple Inc.
3. Google, Android and Google Play are trademarks of Google, Inc.
4. The Bluetooth® word mark and logos are registered trademarks
of Bluetooth SIG, Inc.
5. All other company and product names may be trademarks of the
respective companies with which they are associated.
6. We reserve the right to make changes to our products in the
interests of technical advancement. The products shown may
also look different from the products supplied based on ongoing
enhancement.
7. Reproducing or using texts, illustrations and photos from this
instruction manual in any media – even if only in the form of
excerpts – shall only be permitted with our express written
consent.
8. The design of this manual is subject to copyright protection. We
do not accept any liability for any errors or any erroneous content
or printing errors (even in the case of technical specifications or
within graphics and technical sketches).
9. Our products are in compliance with all technical guidelines,
electrical and telecommunications regulations applicable in
Germany, the EU and the USA.
10. Our products and also the components contained therein
(ICs, software, etc.) may only be used for civilian non-military
purposes.
Data privacy and data security
1. For maximum security, the device uses the same encryption
technologies as are used in online banking. For your security, no
port forwarding or DynDNS is used either.
2. The data centre location for remote access over the Internet by
means of an App is obligatory in the EU if the determined Internet
IP-Address location of the device is within the EU. The data centre
is operated in line with the most stringent security standards.
3. Video, audio and any other surveillance methods can be regulated
by laws that vary from country to country. Check the laws in your
local region before installing and using this device for surveillance
purposes.
If the device is a door-, indoor station or camera:
• In many countries video and voice signal may only be transmitted
once a visitor has rung the bell (data privacy, configurable in the
App).
• Please carry out the mounting in such a way that the detection
range of the camera limits the device exclusively to the immediate
entrance area.
• The device may come with a visitor history and motion sensor. You
can activate/deactivate this function if required.
If necessary, indicate the presence of the device in a suitable place
and in a suitable form.
Please observe any relevant country-specific statutory regulations
concerning the use of surveillance components and surveillance
cameras applicable at the installation site.
Check with the property owner and your house community if you are
allowed to install and use this product. Bird Home Automation GmbH
cannot be held responsible for any miss-use or miss-configuration of
this product, including the unauthorized opening of a door.
Bird Home Automation cannot be held responsible for damages
caused by improper existing installations or improper installation.
Software and operating system’s updates (so-called “firmware
updates”) are generally automatically installed on the products of
Bird Home Automation GmbH via Internet, if technically possible.
Automatic firmware updates keep the products‘ software up to date
so that they always work reliably, safely and efficiently. Through
further development, features can be added, extended or slightly
changed. Major changes or limitations to existing features will
generally occur if Bird Home Automation GmbH deems it necessary
(e.g. for data protection, data security or stability reasons, or to keep
them up to date). When a firmware update is available, Bird Home
Automation GmbH‘s servers generally automatically distribute it to
all compatible products connected to the Internet or Bird Home
Automation GmbH‘s servers. This process is gradual and can take
several weeks. As soon as a product receives a firmware update, the
system will be installed and will restart by itself. Installed firmware
updates cannot be undone. Since the products and software of
Bird Home Automation GmbH are not explicitly customer-specific
products, a customer cannot deny an automatic update if the
product is connected to the Internet or to the Bird Home Automation
GmbH’s server.
Publisher
Bird Home Automation GmbH
Uhlandstraße 165
10719 Berlin
Germany
Web: www.doorbird.com
Email: [email protected]
It is possible that these manual still contains typographical errors
or printing errors.The information in this manual will be checked
regularly and corrections will be made in the next version. We accept
no liability for errors of a technical or printing nature and their
consequences.
17
DEUTSCH
INSTALLATIONSANLEITUNG
Lesen Sie diese Anleitung sorgfältig, bevor Sie die
Komponenten in Betrieb nehmen. Bewahren Sie die
Anleitung zum späteren Nachschlagen auf!
Wenn Sie das Gerät anderen Personen zur
Nutzung überlassen, übergeben Sie auch diese
Bedienungsanleitung.
Die stets aktuelle Version der Installationsanleitung
finden Sie unter www.doorbird.com/de/support
Zur Vereinfachung der Begriffe verwenden wir „Gerät“
für das Produkt „IP Zutrittskotrollgerät A1121“ sowie
„mobiles Endgerät“ für ein Smartphone/Tablet.
Haftung
Die Erstellung dieses Dokuments wurde sorgfältig
vorbereitet. Bitte infor mieren Sie Bird Home
Automation GmbH über etwaige Ungenauigkeiten
oder Unterlassungen. Bird Home Automation GmbH
kann nicht für tech nische oder typografische Fehler
verantwortlich gemacht werden und behält sich das
Recht vor, Änderungen an dem Produkt und den
Handbüchern ohne vorherige Ankündigung vorzu-
nehmen. Bird Home Automation GmbH übernimmt
keinerlei Garantie in Bezug auf das in diesem
Dokument enthaltene Material, einschließlich, aber
nicht beschränkt auf die implizierten Garantien der
Marktgängigkeit und Eignung für einen bestimmten
Zweck. Bird Home Automation GmbH haftet nicht
für Neben- oder Folgeschäden im Zusammenhang mit
der Bereitstellung, Durchführung oder Verwendung
dieses Materials. Das Gerät darf nur für den
vorgesehenen Zweck verwendet werden.
Gerätemodifikationen
Dieses Gerät muss in Übereinstimmung mit den
Anweisungen in der Installationsanleitung installiert
und verwendet werden. Dieses Gerät enthält keine
vom Benutzer zu wartenden Komponenten. Durch
unbefugte Gerätemodifikationen oder Änderungen
erlöschen alle anwendbaren Zertifizierungen und
Zulassungen.
Verwendete Symbole
Achtung: Weist auf eine gefährliche Situation
hin, die, falls nicht verhindert, zum Tod oder
schweren Verletzungen führt.
Warnung: Weist auf eine gefährliche
Situation hin, welche, falls nicht verhindert,
zum Tod oder schweren Verletzungen
führen kann.
Vorsicht: Weist auf eine gefährliche
Situation hin, welche, falls nicht verhindert,
zu geringfügiger oder mäßiger Verletzung
führen kann.
NOTICE Bitte beachten: Weist auf eine gefährliche
Situation hin, welche, falls nicht verhindert,
zu Sachschäden führen kann.
Wichtig: Weist auf wichtige Informationen
hin, die den richtigen Betrieb des Produkts
gewährleisten.
Hinweis: Weist auf nützliche Informationen
hin, die die optimale Verwendung des Geräts
unterstützen.
• Einbau, Montage und Servicearbeiten elek-
trischer Geräte dürfen ausschließlich durch eine
Elektrofachkraft erfolgen. Bei Nichtbeachten
besteht die Gefahr schwerer gesundheitlicher
Schäden oder Lebensgefahr durch elektrische
Stromschläge.
• Geräte mit 110-240 V Anschluss: Das Gerät darf
nur an eine leicht zugängliche Netz-Steckdose
angeschlossen werden. Bei Gefahr ist der
Netzstecker zu ziehen.
• Benutzen Sie für die Stromversorgung des
Gerätes ausschließlich das mitgelieferte
Originalnetzteil, separat erhältliche
Hutschienennetzteile oder einen in dieser
Anleitung empfohlenen PoE-Switch/PoE-
Injektor.
• Durch elektrostatische Aufladung kann bei
direktem Kontakt mit der Leiterplatte das
Gerät zerstört werden. Vermeiden Sie daher ein
direktes Berühren der Leiterplatte zu jeder Zeit.
• Norm EN 60065 bzw. EN 60950 bzw. EN 62368
beachten.
• Verwenden Sie das Gerät nicht, wenn es
von außen erkennbare Schäden z. B. am
Gehäuse, an Bedienelementen oder an den
Anschlussbuchsen bzw. eine Funktionsstörung
aufweist. Im Zweifelsfall lassen Sie das Gerät von
einer autorisierten Fachkraft prüfen.
• Öffnen Sie das Gerät nicht. In solchen Fällen
erlischt jeder Gewährleistungsanspruch! Für
Folgeschäden übernehmen wir keine Haftung!
Das Gerät enthält keine durch den Anwender
zu wartenden Teile. Im Fehlerfall lassen Sie das
Gerät von einer autorisierten Fachkraft prüfen.
• Aus Sicherheits-, Zulassungs- und
Lizenzgründen (CE/FCC/IC etc.) ist das
eigenmächtige Umbauen und/oder Verändern
des Gerätes nicht gestattet.
• Das Gerät ist kein Spielzeug! Erlauben Sie
Säuglingen und Kindern nicht damit zu spielen.
• Um Erstickungsgefahr zu vermeiden, halten
Gefahrenhinweise
WARNUNG
18
Sie das Verpackungsmaterial von Säuglingen
und Kindern fern. Plastikfolien/-tüten,
Styroporteile etc. sind kein Spielzeug und
können gefährlich für Kinder sein. Entsorgen
Sie das Verpackungsmaterial sofort nach der
Entnahme des Produkts. Verwenden Sie das
Verpackungsmaterial nicht wieder.
• Verlegen Sie Kabel stets so, dass diese keine
Gefährdungen für Menschen und Haustiere
darstellen.
• An Teilen im Gerät liegt Spannung an.
Berühren Sie keine Teile, die nicht mit der
Installation, der Verdrahtung oder dem
Anschluss verbunden sind. Elektrische
Stromschläge können die Folge sein.
• Halten Sie die Geräte, die nicht als wetterfest
gekennzeichnet sind, von Wasser oder anderen
Flüssigkeiten fern.
• Führen Sie keine Installation durch und
stellen Sie keine Verbindungen her, während
die Stromversorgung eingeschaltet ist.
Beschädigungen am Gerät oder elektrische
Stromschläge können die Folge sein.
• Bevor Sie die Stromversorgung einschalten,
stellen Sie sicher, dass die Drähte nicht
gekreuzt oder kurzgeschlossen sind. Feuer
oder elektrische Stromschläge können die
Folge sein.
• Hochspannung kann intern vorhanden
sein. Öffnen Sie das Gerät nicht. Elektrische
Stromschläge können die Folge sein.
• Das Gerät ist nicht explosionsgeschützt. Nicht
in der Nähe von Gasen oder brennbaren
Materialien installieren oder verwenden. Feuer
oder Explosion können entstehen.
• Installieren Sie nicht zwei Stromversorgungen
parallel zu einem einzigen Eingang. Feuer oder
Beschädigung des Gerätes können entstehen.
Achten Sie darauf, nur ein einziges Netzteil an
das Gerät anzuschließen.
• Schließen Sie keinen Anschluss am Gerät
an eine Netzstromleitung an. Feuer oder
elektrische Stromschläge können die Folge
sein.
• Stellen Sie sicher, dass das Netzkabel nicht
beschädigt oder gequetscht ist. Wenn das
Netzkabel gebrochen ist, kann es zu einem
Brand oder elektrischen Stromschlag kommen.
• Nichts mit nassen Händen anstecken oder
abziehen. Elektrische Stromschläge können
die Folge sein.
• Führen Sie kein Metall oder brennbares
Material in das Gerät. Feuer, elektrische
Stromschläge oder Gerätestörungen können
die Folge sein.
• Bestehende Verdrahtungen wie Türgong-
verdrahtung usw. können Hochspannungs-
Wechselstrom enthalten. Schäden am Gerät
oder elektrische Stromschläge können
auftreten. Die Verdrahtung und Installation
muss von einem qualifizierten Elektriker
durchgeführt werden.
• Gerätemontage an Wand oder Decke:
Vermeiden Sie Installationsorte, an denen das
Gerät Erschütterungen oder Stößen ausgesetzt
ist.
• Bei Geräten mit Erdungsklemmen muss eine
Erdung angeschlossen werden. Feuer oder
Gerätestörungen können die Folge sein.
• Bei Geräten mit Kunststoffglas oder Echtglas,
keinen hohen Druck auf das Glas ausüben. Bei
Bruch kann es zu Verletzungen kommen.
• Bei Geräten mit LCD, wenn LCD beschädigt
ist, nicht mit dem Flüssigkristall in Kontakt
kommen. Verletzungen können die Folge sein.
Wenn nötig, spülen Sie den Mund aus, reinigen
Sie Ihre Augen oder Haut mit klarem Wasser für
mindestens 15 Minuten und wenden Sie sich
an Ihren Arzt.
• Bringen Sie nichts auf dem Gerät an und
verdecken Sie das Gerät nicht mit einem Tuch,
Silikon, Klebstoff, Farbe, separater Abdeckung
etc. Es können Feuer- oder Gerätestörungen
auftreten.
• Installieren Sie das Gerät nicht an einer der
folgenden Orte. Feuer, Stromschlag oder
Gerätestörungen können die Folge sein.
Orte unter direktem Sonnenlicht oder
Orte in der Nähe von Heizgeräten, die in
der Temperatur variieren.
Orte mit Staub, Öl, Chemikalien,
Schwefelwasserstoff (heiße Quellen).
Orte, die extremer Feuchtigkeit und Luft-
feuchtigkeit ausgesetzt sind, wie Bäder, Keller,
Gewächshäuser, etc.
Orte, an denen die Temperatur extrem niedrig
ist, wie z. B. in einem gekühlten Bereich oder
vor einer Klimaanlage.
Orte, die Dampf oder Rauch ausgesetzt sind
(z.B. in der Nähe von Heiz- oder Kochflächen).
Orte, an denen Geräusch erzeugende Geräte
wie Dimmschalter oder Wechselrichter-
Elektrogeräte in unmittelbarer Nähe sind.
Orte, die häufigen Vibrationen oder Stößen
ausgesetzt sind.
• Bei Geräten mit Gegensprechfunktion ist darauf
zu achten, dass ein Anruftest durchgeführt wird,
bei dem beide Gegensprechgeräte auf geringer
Lautstärke eingestellt sind. Ein plötzlicher Anruf
etc. kann ankommen und das Gehör schädigen.
• Wenn das Gerät nicht ordnungsgemäß
funktioniert, ziehen Sie den Netzstecker aus der
Steckdose.
WARNUNG
19
DEUTSCH
Sicherheitsanweisungen
• Alle Geräte, die nicht als wetterfest
gekennzeichnet sind, sind nur für den
Innenbereich konzipiert und nicht im Freien
zu benutzen.
• Geräte, die als wetterfest gekennzeichnet
sind, nicht mit Hochdruckwasser besprühen.
Gerätestörungen können die Folge sein.
• Bei Sach- oder Personenschäden, die
durch unsachgemäße Hand habung oder
Nichtbeachten der Gefahrenhinweise
verursacht werden, übernehmen wir keine
Haftung. In solchen Fällen erlischt jeder
Gewährleistungsanspruch! Für Folgeschäden
übernehmen wir keine Haftung.
• Die Verwendung des Geräts muss unter
Beachtung der örtlich geltenden rechtlichen
Bestimmungen erfolgen.
• Lagern Sie das Gerät in einer trockenen und
belüfteten Umgebung.
• Achten Sie darauf, dass das Gerät weder
Stößen noch starkem Druck ausgesetzt ist.
• Installieren Sie das Gerät nicht an instabilen
Halterungen, Oberflächen oder Wänden.
Stellen Sie sicher, dass das Material stabil
genug ist, um das Gewicht des Geräts zu
tragen.
• Verwenden Sie bei der Installation des Geräts
ausschließlich passende Werkzeuge. Ein zu
großer Kraftaufwand mit Werkzeugen kann
das Gerät beschädigen.
• Verwenden Sie keine chemischen, ätzenden
oder aerosolhaltigen Reinigungsmittel.
• Verwenden Sie zum Reinigen ein sauberes,
trockenes Tuch.
• Verwenden Sie nur Zubehör, das den
technischen Daten des Geräts entspricht.
Dieses ist von Bird Home Automation GmbH
erhältlich.
• Verwenden Sie ausschließlich Ersatzteile die
von Bird Home Automation GmbH bereitge-
stellt oder empfohlen werden.
• Versuchen Sie nicht, das Gerät selbstständig
zu reparieren. Wenden Sie sich bezüglich
Reparatur und Wartung an Bird Home
Automation GmbH.
• Halten Sie das Gerät mehr als 1 m (3,3“)
entfernt von Mikrowelle, Radio, TV, WLAN
Router und anderen drahtlosen Geräten.
• Bei Geräten mit Gegensprechfunktion oder
eingebautem Lautsprecher oder eingebautem
Mikrofon oder Signalübertragungsfunktion,
NOTICE
installieren Sie die Drähte mehr als 30 cm
(12‘‘) entfernt von 100-240 V Wechselstromver-
drahtung. Ansonsten können Wechselstrom-
induzierte Geräusche und/oder Geräte-
Störungen auftreten.
• Installieren Sie das Gerät in einem Bereich, der
für zukünftige Inspektionen, Reparaturen und
Wartungen zugänglich ist.
• Wenn das Gerät in der Nähe eines
Mobiltelefons verwendet wird, kann das Gerät
gestört werden.
• Das Gerät kann beschädigt werden, wenn es
fallen gelassen wird. Mit Vorsicht behandeln.
• Das Gerät wird während eines Stromausfalls
außer Betrieb gesetzt.
• Bei Geräten mit Gegensprechfunktion oder
eingebautem Lautsprecher oder eingebautem
Mikrofon kann das Gerät in Bereichen, in denen
Antennen von Mobilfunksendern, Radio- oder
TV-Sendern in der Nähe sind, beeinträchtigt
werden.
• Bei Geräten mit LCD-Bildschirm muss im
Voraus darauf hingewiesen werden, dass
bei einem LCD-Panel, obwohl es mit sehr
hohen Präzisions techniken hergestellt wird,
unvermeidlich ein sehr kleiner Teil seiner
Bildelemente nicht immer beleuchtet oder
gar nicht beleuchten wird. Dies gilt nicht als
Gerätefehler.
• Bei Geräten mit Gegensprechfunktion können
Umgebungsgeräusche um das Gerät herum
eine reibungslose Kommunikation behindern.
Dies ist keine Fehlfunktion.
• Bei Geräten mit Benutzername/Passwort
ist der Anwender für den Zugriff mittels
Benutzername/Passwort auf das Gerät
verantwortlich. Vergewissern Sie sich ein
Passwort zu verwenden, das von einem
Dritten nicht leicht erraten werden kann. Wir
empfehlen Ihnen, das Passwort regelmäßig zu
ändern.
• Wir haften unter keinen Umständen für
Schäden, die aufgrund von Fehlern in der
Stromversorgung, Netzwerkgeräten oder
Endgeräten auftreten; Ausfälle aufgrund von
Internetanbietern und Mobilfunkanbietern;
Ausfälle aufgrund von getrennten oder
gestörten Leitungen und andere Übertragungs-
verluste, die es unmöglich machen, unseren
Dienst zu erbringen, sowie allen anderen
Ursachen die außerhalb unserer Verantwortung
liegen; Oder, wenn während der Übertragung
ein Fehler oder fehlende Daten auftreten.
20
Informationen zur Entsorgung elektrischer
und elektronischer Geräte (für
Privathaushalte)
Dieses Symbol auf Produkten oder begleitenden
Dokumenten weist darauf hin, dass elektrische oder
elektronische Geräte nicht with dem allgemeinen
Hausmüll entsorgt werden sollten. Bitte bringen Sie
solche Produkte zu den vorgesehenen Sammelstellen,
wo sie kostenfrei entgegengenommen und der
geeigneten Abfall- und Wiederverwertung zugeführt
werden. Alternativ dazu können Sie in einigen Ländern
die Produkte beim Kauf eines äquivalenten neuen
Produktes auch bei einem örtlichen Einzelhändler
zurückgeben. Die ordnungsgemäße Entsorgung dieses
Produkts trägt dazu bei, wertvolle Rohstoffe zu sparen
und möglichen negativen Auswirkungen auf die
Gesundheit und die Umwelt vorzubeugen, die durch
eine ungeeignete Abfallentsorgung entstehen können.
Bei den örtlichen Behörden erhalten Sie genauere
Informationen zu Ihrer nächsten zuständigen
Sammelstelle. Abhängig von der nationalen
Gesetzgebung können für die unvorschriftsmäßige
Entsorgung solcher Abfälle Strafen verhängt werden.
Informationen zur Entsorgung in Ländern außerhalb
der Europäischen Union
Dieses Symbol gilt nur in der Europäischen Union.
Wenn Sie dieses Produkt wegwerfen möchten,
kontaktieren Sie bitte die zuständigen Behörden
oder Händler in Ihrem Land, um sich über die
vorschriftsmäßige Entsorgung zu informieren.
Transport
NOTICE Bei Bedarf transportieren Sie das Gerät in
der Originalverpackung oder einer
entsprechenden Verpackung, so dass
Schäden vermieden werden.
Gewährleistung
Informationen zur Gewährleistung des Geräts finden
Sie unter www.doorbird.com/de/warranty
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
Seite laden ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
in anderen Sprachen
- English: DoorBird A1121 Series User manual
- français: DoorBird A1121 Series Manuel utilisateur
- español: DoorBird A1121 Series Manual de usuario
Verwandte Papiere
-
DoorBird A1121 Benutzerhandbuch
-
DoorBird D21x Series IP Video Door Station Benutzerhandbuch
-
DoorBird DB-D101S Bedienungsanleitung
-
DoorBird D21X Installationsanleitung
-
-
DoorBird A1061X Benutzerhandbuch
-
DoorBird A1081 Benutzerhandbuch
-
-
-