Parkside PABK 60 B3 Operation and Safety Notes

Marke: Parkside

Modell: PABK 60 B3

Kategorie: Power-Feinsprühsysteme

Typ: Operation and Safety Notes

Cover.indd 1 16.06.2017 11:11:56

IAN 285126

Stand der Informationen: 05/2017

Katharina-Loth-Str. 15

DE-66386 St. Ingbert

GERMANY

C.M.C. GmbH

Ident.-No.: PABK60B3032017-GB/DK/FR/BE/NL/DE

Cover.indd 2 16.06.2017 11:11:56

IAN 285126

AIRBRUSH-SET PABK 60 B3

AIRBRUSH-SET

Operation and Safety Notes

Translation of the original instructions

www.lidl-service.com

DE CHAT

GB NIIE

AIRBRUSH-SET

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

DE CHAT

GB NIIE

Cover.indd 3 16.06.2017 11:11:58

DE / AT / CH Montage-, Bedienungs- und Sicherheitshinweise Seite 21

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich an

schließend mit allen Funktionen des Gerätes vertraut.

DE CHAT

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions

of the device.

GB IE

GB / IE / NI Operation and Safety Notes Seite 5

Cover.indd 4 16.06.2017 11:11:58

2 3

Cover.indd 5 16.06.2017 11:12:03

Cover.indd 6 16.06.2017 11:12:03

G H

Cover.indd 7 16.06.2017 11:12:09

5 GB/IE/NI

Table of contents

The following pictograms are used in these instructions for

use / on the device ...................................................................................................................Page 6

Introduction ................................................................................................................................... Page 6

Intended Use .......................................................................................................................................Page 6

Features ...............................................................................................................................................Page 6

Technical Data ....................................................................................................................................Page 7

General safety instructions for pneumatic tools ............................................Page 7

General safety instructions for electrical devices ..............................................................................Page 11

Product-specific safety instructions .....................................................................................................Page 12

Before Use ...................................................................................................................................... Page 12

Initial use .........................................................................................................................................Page 12

Connect airbrush set ...........................................................................................................................Page 13

Mixing paints for use ..........................................................................................................................Page 13

Switching the airbrush compressor on / off .......................................................................................Page 13

Regulating the air pressure ................................................................................................................. Page 13

Regulating the result of the spray stylus .............................................................................................Page 13

Connecting the pneumatic hose .........................................................................................................Page 13

Using the mini paint spray gun ...........................................................................................................Page 14

Mini spray gun initial use ..................................................................................................Page 14

HVLP properties ................................................................................................................................... Page 14

Connecting the device ........................................................................................................................Page 14

Preparing the spraying surface ..........................................................................................................Page 14

Switching the device on and off .........................................................................................................Page 14

Adjust paint jet .....................................................................................................................................Page 15

Regulating the paint volume ............................................................................................................... Page 15

Regulating the air quantity..................................................................................................................Page 15

Maintenance and Cleaning ..............................................................................................Page 15

Cleaning and care .................................................................................................................... Page 16

Warranty and service information ...........................................................................Page 17

Warranty terms ...................................................................................................................................Page 17

Extent of warranty ............................................................................................................................... Page 17

Processing of warranty claims ............................................................................................................ Page 17

Environmental instructions and disposal information ..............................Page 18

Paint disposal instructions ................................................................................................Page 18

EC Declaration of Conformity ......................................................................................... Page 19

285126_Airbrush-Set PABK 60 B3_content_IE.indd 5 14.06.17 16:34

6 GB/IE/NI

Introduction / General safety instructions for pneumatic tools

Introduction

The following pictograms are used in these instructions for use / on the device:

Note Supply hose

Observe the warnings and safety

notices!

Danger of electric shock

Never use hydrogen, oxygen, carbon

dioxide or another bottled gas as an

energy source.

Risk of burns! Warning - hot surfaces.

Wear ear protection, dust mask, safety

glasses and protective gloves.

Dispose of the packaging and device

in an environmentally-friendly manner!

For indoor use only.

Warning:

Compressor unit can start up without

warning.

Airbrush Set PABK 60 B3

Introduction

Congratulations! You have chosen a

high-quality unit from our company. Fa-

miliarise yourself with the product before

using it for the ﬁrst time. In addition, please carefully

read the instructions for use and the safety instruc-

tions below. Initial operation of this tool must be

performed by trained personnel.

KEEP OUT OF REACH

OF CHILDREN!

Intended Use

This device is a portable pneumatic compressor

optimised for use with airbrush devices.

With the accessories included, it is suitable for use

in numerous applications. It is maintenance-free

and equipped with noise suppression so it is also

suitable for use in closed rooms. Keep these instruc-

tions in a safe place.

When passing this product on to others, please

also include all the documents. Any use other than

the intended is prohibited and potentially

dangerous. Damages resulting from noncompliance

or misuse are not covered by the warranty and are

not included in the manufacturer's liability. This de-

vice was designed for household use and may not

be used for commercial or industrial purposes.

Features

Check that all the items are present and

that the product is in perfect condition

immediately after unpacking. Never use

the product if it is defective.

Airbrush compressor

Coiled hose

2 a

Coiled hose adapter

Spray stylus

Paint mixing beaker with connection lid

On / Oﬀ switch

Air pressure regulator

Compressed air hose

Air blow gun

6 colours

Open-end wrench

Mini paint spray gun

Lid of the gravity ﬂow cup

Gravity ﬂow cup

Material amount regulation screw

285126_Airbrush-Set PABK 60 B3_content_IE.indd 6 14.06.17 16:34

7 GB/IE/NI

Introduction / General safety instructions for pneumatic tools

Introduction

Regulator for round jet / broad jet

Compressed air connection

Regulator for air quantity control

Trigger

Nozzle head

Needle

Spring

Brush (not included in delivery, tooth / nail

brush)

Filter

Inner screw thread

Stirring rod

In addition, this pack contains six diﬀerent coloured

high concentrate and water soluble paints in plastic

pots. These are referred to as "consumables" in the

following.

Technical Data

Output power: approx. 15 l / min

Theoretical suction capacity: max. 40 l / min

Operating pressure: max. 0.26 MPa

Max. pressure: 0.32 MPa (approx.

3 bar)

Weight without accessories: 2.5 kg

Engine power without load: 180 W

Operating voltage: 230 V∼, 50 Hz

Operating mode S3 15%

Duty cycle 10 min: S3 = intermittent duty

without the inﬂuence

of start-up process.

Within a period of

10 minutes the maxi-

mum operating time

may amount to 15%

(1.5 min).

Operating level of

compressor speed: 4440 min

-1

Protection type: IPX0

Protection class: I /

Ambient temperature

during operation: 10°C - 30°C

Mini spray gun:

Operating pressure: max. 3 bar

Nozzle size: Ø 1.4 mm

Gravity ﬂow cup: approx. 100 ml

Recommended viscosity: 18-23 DIN/sec.

Noise emission value:

Measurement for noise level, determined according

to EN 14462. The evaluated noise level at the

position

of the user is:

Noise level: LPA=72.1 dB(A)

Uncertainty: KPA=2.5 dB (A)

General safety

instructions for

pneumatic tools

Note: the term "pneumatic device"

or "device" used in the following

text refers to the pneumatic device

that is the subject of these instructions

for use.

Basic safety

measures must be followed when

using compressed air devices, to

eliminate the risk of ﬁre, electric

shock and personal injury. Be sure

to read and follow the notices within

these operating instructions prior to

using the equipment and store them

in a safe location. The manufacturer

assumes no liability for damages or

285126_Airbrush-Set PABK 60 B3_content_IE.indd 7 14.06.17 16:34

8 GB/IE/NI

General safety instructions for pneumatic tools

personal injury resulting from failure

to follow these operating instructions.

This device may be used by

children aged 8 years and up, as

well as by persons with reduced

physical, sensory or mental ca-

pacities, or lacking experience

and / or knowledge, so long as

they are supervised or instructed

in the safe use of the device and

understand the associated risks.

Do not allow children to play

with the product. Cleaning and

user maintenance must not be

performed by children without

supervision.

Prevent children from playing

with the device.

RISK OF INJURY! Before

performing maintenance tasks,

disconnect the compressed air

supply.

Only use the device in areas of

application for which it was

designed!

Do not overload the device.

Never use hydrogen,

oxygen, carbon dioxide

or another bottled gas as an en-

ergy source for this product, as

this can lead to an explosion

and therefore also to serious in-

juries.

Maintain and clean the device

regularly as prescribed (see

section "Cleaning and care").

DANGER OF EXPLOSION!

Never use petrol or another

ﬂammable liquid to clean the

pneumatic device! Sparks could

ignite residual vapours inside the

compressed air unit resulting in

the compressed air unit explod-

ing. Do not work with the device

in potentially explosive environ-

ments, which contain ﬂammable

liquids, gases or dusts. Never

work on materials which are or

could potentially be highly ﬂam-

mable or explosive.

Check the device for damage

before startup. Always make

sure that the device is in perfect

condition before each use.

Always be attentive! Unexpected

movement of the device may

cause hazards.

Avoid placing your body in an

unnatural position. Keep proper

footing and balance at all times.

By doing this you will be in a

better position to control the com-

pressed air unit in unforeseen

circumstances.

285126_Airbrush-Set PABK 60 B3_content_IE.indd 8 14.06.17 16:34

9 GB/IE/NI

General safety instructions for pneumatic tools

Never use a device with a switch

that is defective. A device that

can no longer be switched on

and oﬀ is dangerous and must

be repaired.

Store the idle pneumatic device

out of the reach of children. Do

not let anyone use the device who

is not familiar with it or has not

read these instructions. Pneumatic

devices are dangerous when

they are used by inexperienced

people.

Maintain the device with care.

Check that moving device parts

are working properly and move

freely. Check for any parts that

are broken or damaged enough

to detrimentally aﬀect the func-

tioning of the device. Have dam-

aged parts repaired before using

the equipment. Many accidents

have their origins in poorly main-

tained devices.

Turn the device oﬀ when it is no

longer in use.

Wear personal protective

equipment and always

wear protective glasses. Wear-

ing personal protective equipment

such as a dust mask, non-slip

safety shoes, a safety helmet or

ear protectors, depending on

the type of pneumatic tool and

its application, reduces the risk

of injuries.

Test the connections and the

supply cable. All maintenance

units, couplings and hoses must

be designed in accordance with

the device's values with regard

to pressure and air quantity.

Pressure that is too low impairs

the functioning of the device;

pressure that is too high can

cause damage to property and

personal injury.

Protect hoses from kinks, con-

strictions, solvents and sharp

edges. Keep hoses away from

heat, oil and rotating parts.

Ensure that the hose clips are al-

ways ﬁrmly attached. If the hose

clamps are not tightly fastened

or are damaged, the air could

escape uncontrollably.

Replace damaged hoses imme-

diately. A damaged supply line

may result in the air hose whip-

ping about and may result in

injuries.

If the power cable of the appli-

ance is damaged, it must be

replaced by the manufacturer

or their service department or a

similarly qualiﬁed person, in

order to avoid hazards.

285126_Airbrush-Set PABK 60 B3_content_IE.indd 9 14.06.17 16:34

10 GB/IE/NI

General safety instructions for pneumatic tools

Do not use the device when

tired or under the inﬂuence of

drugs, alcohol or medications.

One moment of carelessness

when using the device may

result in serious injuries.

Do not directly inhale the exhaust

air. Avoid getting exhaust air in

the eyes. Exhaust air from the air

tool may contain water, oil, metal

particles or contaminants from

inside the compressor. These

may damage your health.

BE CAREFUL

WHEN PUTTING DOWN

THE DEVICE! Always put down

the device so that it is not resting

on the trigger. This could poten-

tially result in accidental activa-

tion of the device, which again

could result in hazards.

Only use suitable accessories.

These may be purchased from

the manufacturer. Using non-OEM

accessories may result in hazards.

Only use ﬁltered and regulated

compressed air. Dust, caustic

vapours and / or moisture may

damage the motor of the com-

pressed air tool.

The hose must be de-

signed for a pressure of

at least 8.6 bar or 125 psi, or at

least 150% of the maximum

pressure created in the system.

The tool and the feed

hose must be provided

with a hose coupling so that the

pressure is completely relieved

by the release of the hose cou-

pling.

The pneumatic device may not

be modiﬁed in any way without

the permission of the manufac-

turer.

Only use the pneumatic device

with the prescribed pressure

(max. 0.32 MPa / approx. 3 bar).

The pneumatic device must always

be separated from the air feed

after use or if it is not in use.

Do not use the compressed air

device if it leaks or is in need of

repair.

Never connect the pneumatic

device with a pneumatic hose

whose pressure exceeds 7 bar.

Keep your working area clean

and well lit. Untidy or poorly lit

working areas can result in acci-

dents. Doing so will allow you

better control of the device,

particularly under unforeseen

circumstances.

Only allow the

device to be maintained and

285126_Airbrush-Set PABK 60 B3_content_IE.indd 10 14.06.17 16:34

11 GB/IE/NI

General safety instructions for pneumatic tools

serviced by qualiﬁed service

personnel. This will maintain the

safety of the device.

Keep children and other persons

away from the device during

use. Distractions can cause you

to lose control of the equipment.

Wear suitable clothing. Do not

wear loose clothing or jewellery.

Keep your hair, clothing and

gloves clear of moving parts.

Loose clothing, jewellery or long

hair can become trapped in

moving parts.

Put down trigger and device in

the event of unexpected com-

pressor failure.

Use a condensate separator if

possible or regularly empty the

hose and the pipeline of con-

densation (water) before and

during use of the pneumatic

device.

ATTENTION! An un-

dersized compressed air

system may reduce the eﬃciency

of your device.

Never direct the pneumatic de-

vice at yourself, other people or

animals. Injuries may otherwise

occur.

Observe all safety instructions

attached to the compressor.

Ensure that the compressor's suc-

tion opening can is clear and

can suck in air.

Clean the suction ﬁlter with a

cloth if it shows contamination.

Switch oﬀ the device and pull

the plug from the socket to pre-

vent it from being accidentally

switched on.

Do not allow yourself to be dis-

tracted whilst working with the

device.

General safety

instructions for

electrical devices

Connect the device via a residual

current device (RCD).

Protect yourself against electric

shock.

Avoid touching earthed parts

during work (such as for exam-

ple fridge, water pipes etc.).

DANGER! Avoid contact with

live lines. This device is not insu-

lated against electric shock.

Regularly check the extension

and power cables. Replace any

faulty cables with new ones

immediately.

If the mains power cable of this

device is damaged, it must be

285126_Airbrush-Set PABK 60 B3_content_IE.indd 11 14.06.17 16:34

12 GB/IE/NI

Initial use

General safety instructions for pneumatic tools / Before Use / Initial use

replaced by the manufacturer

or their service department or a

similarly qualiﬁed person, in

order to avoid hazards.

Store the device in a dry envi-

ronment if it will not be in use for

an extended period of time.

Make sure that the connection

cable is not hanging over a cor-

ner and is not stretched taut; oth-

erwise there is a risk of injury.

Do not use the mains lead for

any purpose for which it was not

intended, e.g. to carry the prod-

uct, to hang it up or to pull the

mains plug out of the mains

socket.

Never pull on the mains cable to

remove the mains plug from the

socket.

Do not use electronic tools in a

wet or damp environment; do

not expose them to rain or high

levels of moisture.

Never connect electrical tools

near highly ﬂammable liquids or

gases.

If you are working outside, only

use an extension cable that is

explicitly intended for that use.

Product-speciﬁc safety

instructions

CAUTION! HAZARD

OF BURNS! The

Compressor will warm up when

it used for a long time. Therefore

always use the handle on the

device to move it. Never touch

the device itself!

Attention! The casing of the

airbrush compressor may become

hot during use. Do not touch hot

surfaces, in order to prevent

burns.

Never leave the device in opera-

tion unattended. Built-up heat

generated by the device can be

a source of danger.

Before Use

Check that all parts of the device are in perfect

condition.

Check whether your available voltage is com-

patible with the compressor.

Note: you will ﬁnd the intended mains voltage

on the type plate of the device.

Initial use

Note: the device slides around with correct use on

smooth surfaces. This can be prevented by gently

pressing down the device.

Clean dusty surfaces so that the suction cups can

grip well. Otherwise a slight shift in position is

possible.

285126_Airbrush-Set PABK 60 B3_content_IE.indd 12 14.06.17 16:34

13 GB/IE/NI

Initial use

General safety instructions for pneumatic tools / Before Use / Initial use

Connect airbrush set

Always unplug from the mains before you

connect the airbrush set with the compressor.

Use the relevant screw connection to connect

the spray stylus

with the coiled hose

and the coiled hose to the airbrush compressor

. Use the included open-end wrench.

(see Fig. A).

Fasten the paint mixing beaker with the con-

nection lid to the spray stylus

(see Fig. B).

Connect the mains plug to the mains socket.

Note: for optimal results, professionals use an

interposed pressure reducer (not included in

delivery). The pressure reducer can be used to

adjust the compressed air at the spray gun and

optimise it to your needs.

Mixing paints for use

The paints included are water-soluble. In order to

properly apply the paints, add water and stir. As

delivered, the paints are too viscous.

Shake the colour tube with the cap still on.

Put 3-4 drops of the colour in the mixing

beaker.

Fill the jar half full with water and stir with the

stirring rod

It is important that there are no clumps. Screw

the lid onto the beaker.

Connect the paint mixing beaker

according

Figure B.

Note: if you wish, you can use the quantity of

water you add to inﬂuence the colour strength,

as with water colour paints. The more water

you add, the "thinner" the colour. You can also

mix individualised colour tones from the availa-

ble colour pastes. Ensure that there are no

paint clumps in the paint containers. The con-

sistency should correspond to that of water.

Note: if the used colour is too opaque, in-

crease the quantity of colour in the mixture.

Switching the airbrush

compressor on / oﬀ

Turn the airbrush compressor

on by setting

the on / oﬀ switch

to the position "I" (see

Fig. C).

Turn the airbrush compressor

oﬀ by setting

the on / oﬀ switch

to the

position "0" (see Fig. C).

Note: full pressure is reached after approx.

two seconds.

Regulating the air pressure

Regulate the air pressure by adjusting the air

pressure measurement button on the top side

of the spray stylus

The air pressure can be adjusted by turning the

air pressure regulator

The level of air pressure will be shown on the

pneumatic display.

Turning the air pressure regulator

to the left

lowers air pressure; turning the air pressure reg-

ulator

to the right increases air pressure.

An internal valve bleeds overpressure if it is not

reduced.

Regulating the result of the

spray stylus

Regulate quantity of paint in use and therefore

also the result of the spraying by turning paint

nozzle on the spray stylus to the left (see Fig. B).

Connecting the pneumatic hose

Connect the pneumatic hose

to the airbrush

compressor

. Use the included open-end

spanner

to do so (compare Fig. A).

285126_Airbrush-Set PABK 60 B3_content_IE.indd 13 14.06.17 16:34

14 GB/IE/NI

Mini spray gun initial use / Maintenance and Cleaning

Initial use / Mini spray gun initial use

Using the mini paint spray gun

Connect the hose with the switched oﬀ compressor.

The device is exclusively intended for the application

or spraying of solvent-based and water-dilatable

paints, glazes, primers, varnishes, vehicle varnish,

mordants, wood preservatives, plant protection

agents, oils and disinfectants. Do not use the de-

vice to process emulsion or latex paints, lye, acidic

spray materials or anti-spray or anti-run materials.

Any further use of or changes to the device are

considered improper use and could entail consider-

able damages. We do not assume any liability for

damage arising from improper use. This device is

solely intended for private use.

Insert the ﬁlter

in the paint tank of the paint

spray gun

is shown in Figure G.

Screw the gravity ﬂow cup

into the paint

tank in a clockwise direction.

Screw the mini paint spray pistol onto the air

pressure hose.

Unscrew the lid of the paint container from the

mini paint spray gun and ﬁll this with thinned

airbrush paint. Ensure that the paint is not to

thick to prevent it from clogging up the gun.

Replace the lid.

Pull the trigger to spray. You can adjust the jet

by turning the nozzle.

Clean the device after spraying.

Mini spray gun initial use

HVLP properties

This device uses an HVLP system (High Volume Low

Pressure). It provides a more eﬃcient application of

(paint)

materials with a lower consumption.

IMPORTANT: do not exceed the operating pres-

sure of a maximum of 3 bar.

Connecting the device

NOTE

Be sure you have the correct operating pres-

sure. Excessive operating pressure leads to ﬁner

dispersion and has the result that liquids evap-

orate too quickly. The surfaces become rough

and develop poor adhesion properties. If the

operating pressure is too low on the other hand,

the paint material is not suﬃciently atomised.

Undulating surfaces and the formation of drops

are the result.

Preparing the spraying surface

The area surrounding the area to be sprayed

should be thoroughly and liberally covered.

Otherwise all non-covered areas or surfaces

may become soiled.

Make sure that the spraying surface is clean,

dry and free of grease.

Roughen smooth surfaces (e.g. with sandpaper)

and then remove the dust created.

Switching the device

on and oﬀ

Working Instructions:

When thinning, ensure that the spray material

and the thinner are compatible. If you use the

wrong thinner, clumps can be created and the

gun can become clogged.

Screw the gravity ﬂow cup

to the gun in a

clockwise direction.

Fill the gravity ﬂow cup

with the spray

material and screw the lid tight.

Always hold the paint spray gun at the same

distance from the object. The ideal spraying

distance is approximately 15 cm.

Perform a trial to determine the suitable

settings.

Do not turn the device on / oﬀ over the area to

be sprayed, but rather begin and end the

spraying procedure approx. 10 cm outside the

area to be sprayed.

285126_Airbrush-Set PABK 60 B3_content_IE.indd 14 14.06.17 16:34

15 GB/IE/NI

Mini spray gun initial use / Maintenance and CleaningInitial use / Mini spray gun initial use

Switching on:

To turn on, press the trigger lever

and hold

it pressed down.

Switching off:

To end operation, release the trigger lever

Adjust paint jet

The device has two settings: round and broad jet.

Round jet Broad jet

Adjusting the round jet:

The round jet is suitable for areas such as small

surfaces, corners and edges.

Turn the regulator

in a clockwise direction.

Adjusting the broad jet:

The broad jet is suitable for larger surfaces, both

vertical and horizontal.

Turn the regulator

in an anticlockwise

direction .

The nozzle head can be continuously adjusted

to the correct position vertically and horizontally

by being turned towards the desired position.

Regulating the paint volume

NOTE

The front locking screw serves to restrict the adjust-

ment range of the material amount regulation

screw

Increasing the quantity of paint:

Turn the material amount regulation screw

in an anticlockwise direction.

Reducing the quantity of paint:

Turn the material amount regulation screw

in a clockwise direction.

Regulating the air quantity

NOTE

We recommend you begin with the maximum

air quantity. To do this, open the air volume

regulator to the maximum as is described

below under "Increasing air quantity".

Increasing the air quantity:

NOTE

We recommend you increase the air quantity if

the spray ﬁeld is too course.

Turn the air quantity regulator

in a clock-

wise direction.

Reducing the air quantity:

NOTE

We recommend you decrease the air quantity

if the paint mist is too strong.

Turn the air quantity regulator

in a clock-

wise direction.

Maintenance and Cleaning

DANGER OF INJURY!

Before maintenance works, separate the device

from the pneumatic network.

NOTE

Thorough cleaning after every operation is

very important for safety and use. Otherwise

for example the needle becomes clogged and

the device's functioning is no longer guaranteed.

Wear suitable protective gloves when carrying

out cleaning work.

Do not use any hydrocarbon-containing

halogen solvents, such as trichloromethyl, ethyl

chloride, etc., as they undergo chemical reac-

tions with some materials of the paint spray

gun. This can lead to dangerous reactions.

285126_Airbrush-Set PABK 60 B3_content_IE.indd 15 14.06.17 16:34

16 GB/IE/NI

Cleaning and care / Warranty and service information

Cleaning and care

Thoroughly clean the spray stylus

immedi-

ately after use. Otherwise the paint can dry

and cause problems during the next use.

Rinse out the spray stylus

thoroughly with

water. Do the same with the mini paint spray

gun.

Note: should the compressor's air duct be

dirty, remove the sucked in dirt using a dry

cloth.

ATTENTION!

Never submerge the paint spray gun in solvents.

After each use, spray thinner (only in the open

air – danger of explosion!) or water through

the device.

Use a cleaning brush or a cloth. to clean the

casing, the nozzle head and the spray holes

contained within. Never use petrol, solvents or

cleaning agents that attack plastic.

First screw out the material amount regulation

screw by turning in an anticlockwise direction.

Remove the spring.

Remove the needle using pliers (see Figure A).

Clean the needle carefully using the brush

(tooth / nail brush) (see Figure B).

Put the needle back in the paint spray gun.

Place the spring on the end of the needle.

Error Interrupted paint jet

or intermittent

colour coverage

Cause Solution

1. Paint almost

empty

1. Fill paint

2. Viscosity too

high

2. Lower viscosity

3. Nozzle loose /

defective

3. Replace / screw nozzle

tight

Screw the material amount regulation screw

tight by turning in a clockwise direction.

Unscrew the gravity ﬂow cup from the mini spray

gun by turning in an anticlockwise direction.

Remove the ﬁlter as shown in Figure C and

clean this with a tooth / nail brush.

Also clean the gravity ﬂow cup's inner screw

thread using a tooth or nail brush (see Figure D).

Insert the ﬁlter back into the gun (see Figure C)

and screw the gravity ﬂow cup tight in a clock-

wise direction.

For rust protection you can spray sewing

machine oil through the device after cleaning.

For this purpose, spray sewing machine oil in

through the spray gun.

Oil all moving parts regularly to ensure the

smooth operation of the device.

After cleaning the needle, the thread and seal

must be lightly greased.

Do not use any lubricants containing silicone.

Only store pneumatic tools in dry areas.

Error Reduced performance

Cause Solution

4. Paint supply

restricted

4. Clean

5. Spray stylus

in incorrect

position

5. Correct angle of

position

Error Spray pattern not

complete

Cause Solution

1. Air head dirty /

defective

1. Clean / replace air

head

1. Rinse with clear water

2. Contaminated /

defective nozzle

2. Clean / replace nozzle

Error Spray pattern

irregular with

formation of drops

Cause Solution

1. Defective nozzle 1. Replace nozzle.

Go to a suitable service

station for this purpose.

2. Viscosity too high

2. Lower viscosity

285126_Airbrush-Set PABK 60 B3_content_IE.indd 16 14.06.17 16:34

17 GB/IE/NI

Cleaning and care / Warranty and service information

Cleaning and care

Error Spray pattern

irregular with

formation of drops

Cause Solution

3. Operating pres-

sure too low

3. Increase operating

pressure (if applicable,

adjust accessories not

included in delivery, e.g.

pressure reducer)

3. Defective hose,

replace hose

Error Uneven discharge of

paint quantity

Cause Solution

Contaminated /

defective nozzle

Clean / replace nozzle

Warranty and service

information

Creative Marketing Consulting GmbH

warranty

Dear customer, the warranty period for this device

is 3 years from the date of purchase. In the event of

product defects, you have legal rights against the

retailer of this product. Your legal rights are not lim-

ited in any way by our warranty detailed below.

Warranty terms

The warranty period begins on the date of pur-

chase. Please keep the original sales receipt in a

safe location. This document is required as your

proof of purchase.

If a material or manufacturing defect appears in

the product within three years of the date of pur-

chase, we will repair or replace it - at our discretion

- free of charge. This warranty is conditional on the

defective device and the receipt of purchase being

presented within the three year warranty period,

and on there being a brief written description of

the nature of the defect and of the date it arose.

If the defect is covered by our guarantee, you will

get a repaired or new product back. A new guar-

antee period begins with the repair or exchange of

the product.

Extent of warranty

The device has been manufactured according to

strict quality guidelines and thoroughly inspected

before delivery.

The warranty applies to defects in material or

manufacture. This guarantee does not extend to

product parts subject to normal wear and tear

which can therefore be considered as wear items,

or to damaged fragile parts, e.g. switches, batter-

ies or glass parts.

This guarantee becomes void if the product has

been damaged, or used or maintained improperly.

For a proper use of the product, all instructions in

the instructions of use must be strictly complied with.

Uses and actions which are advised or warned

against in the instruction manual should absolutely

be avoided.

The product is intended for private, non-commercial

use. In the event of misuse or improper handling,

or any kind of intervention which has not been

performed by our authorised service oﬃce, the

guarantee will lapse.

Processing of warranty claims

In order to ensure that your concern is dealt with

quickly, please comply with the following notes:

Please have your receipt and the item number (e.g.

IAN) ready as proof of purchase.

You can ﬁnd the item number on the type plate, an

engraving, the title page of your instructions (bot-

tom left), or on the sticker on the back / base.

285126_Airbrush-Set PABK 60 B3_content_IE.indd 17 14.06.17 16:34

Seite laden ...

Parkside PABK 60 B3 Operation and Safety Notes

Marke: Parkside

Modell: PABK 60 B3

Kategorie: Power-Feinsprühsysteme

Typ: Operation and Safety Notes

PDF Herunterladen

Bericht

in anderen Sprachen

English: Parkside PABK 60 B3

Parkside PABK 60 B3 Operation and Safety Notes

Parkside PABK 60 B3 Operation and Safety Notes

in anderen Sprachen

Verwandte Papiere

Sonstige Unterlagen