Lidl STS 12 B2 Operating Instructions Manual

IAN 284710

TV SIMULATOR STS 12 B2

TV SIMULATOR

Operating instructions

TV-SIMULATOR

Bedienungsanleitung

GB / IE/ NI Operating instructions Page 1

DE / AT / CH Bedienungsanleitung Seite 19

Before reading, unfold the page containing the illustrations and

familiarise yourself with all functions of the device.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und

machen Sie sich anschließend mit allen Funktionen des Gerätes

vertraut.

STS 12 B2 GB│IE│NI │ 1 ■

Index

Introduction ...............................2

Copyright .................................2

Intended use ..............................2

Scope of delivery and transport inspection .....3

Unpacking ...................................... 4

Disposal of the packaging ......................... 4

Operating elements ........................4

Technical data .............................5

Safety instructions .........................6

Functions .................................8

Setup ....................................9

Wall mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Operation ...............................12

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Storage .................................14

Disposal of the appliance ...................14

Appendix ................................15

Kompernass Handels GmbH warranty ...............15

Service .......................................18

Importer ......................................18

STS 12 B2

■ 2 │ GB│IE│NI

Introduction

Congratulations on the purchase of your new appliance.

You have clearly decided in favour of a high-quality product.

These operating instructions are a part of this product. They

contain important information in regard to safety, use and

disposal. Before using the product, familiarise yourself with

all operating and safety instructions. Use this appliance only

as described and only for the speciﬁed areas of application.

In addition, pass these operating instructions on to whoever

might acquire the appliance at a future date.

Copyright

This documentation is copyright protected.

Any copying or reproduction of it, including as extracts,

as well as the reproduction of images, also in an altered

state, is only permitted with the written authorisation of the

manufacturer.

Intended use

This appliance is used to simulate light proportions similar

to those created by a TV set. This appliance is intended

exclusively for indoor use in private households. Do not use

it for commercial applications!

WARNING

Risks from unintended use!

Risks can be engendered if the appliance is used for

unintended purposes and/or other types of use.

► Use the appliance exclusively for its intended purposes.

► Observe the procedures described in these operating

instructions.

STS 12 B2 GB│IE│NI │ 3 ■

Claims of any kind for damage resulting from unintended

use, incompetent repairs, unauthorised modiﬁcation or the

use of unauthorised spare parts will not be accepted. The

user alone bears the risk.

Scope of delivery and

transport inspection

WARNING

► Packaging materials should not be used as a plaything.

There is a risk of suﬀocation.

This appliance is supplied with the following components as

standard:

▯ TV Simulator

▯ Power adapter

▯ Assembly material (2 screws, 2 plugs, adhesive strips)

▯ Operating instructions

NOTE

► Check the contents to ensure that everything is available

and for signs of visible damage.

► If the contents are not complete, or are damaged

due to defective packaging or through transportation,

contact the Service Hotline (see chapter Service).

STS 12 B2

■ 4 │ GB│IE│NI

Unpacking

♦ Remove all appliance parts and these operating instruc-

tions from the carton.

♦ Remove all packaging materials from the appliance.

Disposal of the packaging

The packaging protects the appliance against transport

damage. The packaging materials are selected from the

point of view of their environmental friendliness and disposal

technology and are therefore recyclable.

The recirculation of packaging into the material

circuit saves on raw material and reduces the

amount of waste generated. Dispose of packaging

material that is no longer needed as per the

regionally established regulations.

Operating elements

 Light surface

 Power adapter

 Barrel connector

 Plug socket

 Cable conduit

 Switch

 Holes for wall mounting

 Twilight sensor

STS 12 B2 GB│IE│NI │ 5 ■

Technical data

Power adapter Type HX06D-0900200-AB

Input voltage 100 - 240 V ~,

50 / 60 Hz

Current consumption 0,3 A max

Output voltage 9 V (direct current)

Output current 200 mA

Protection class II /

Polarity

Eﬃciency class 5

Appliance

Input voltage 9 V (direct current)

Current consumption 200 mA

Polarity

STS 12 B2

■ 6 │ GB│IE│NI

Safety instructions

RISK OF ELECTRIC SHOCK!

► Ensure that water or moisture cannot

penetrate the appliance.

► Do not use the appliance if the power

adapter or the power cable are dam-

aged.

Use the appliance/the mains adapter

indoors only! Do not use the appli-

ance/the mains adapter outdoors!

WARNING - RISK OF INJURY!

► This appliance may be used by child-

ren aged 8 years and above and by

persons with limited physical, sensory

or mental capabilities or lack of expe-

rience and knowledge, provided that

they are under supervision or have

been told how to use the appliance sa-

fely and are aware of the potential risks.

Children must not use the appliance as

a plaything. Cleaning and user mainte-

nance tasks may not be carried out by

children unless they are supervised.

STS 12 B2 GB│IE│NI │ 7 ■

WARNING - RISK OF INJURY!

► Do not use the appliance if people

suﬀering from epilepsy are in the

room. The changes in light levels can

cause epileptic seizures in people

susceptible to them.

► Before use, check the appliance for

visible external damage. Do not oper-

ate a damaged appliance or one that

has been dropped. There is also a

risk of personal injury!

► Never look directly into the LEDs!

They are very bright and can caause

injury to the eyes!

► Repairs must only be carried out by

authorised specialist companies or by

the Customer Service. Incompetent

repairs may result in risks for the user.

In addition, warranty claims become

void.

► Place the power cable such that no

one can stumble over it.

STS 12 B2

■ 8 │ GB│IE│NI

CAUTION - PROPERTY DAMAGE

► Do not operate the appliance close to

open ﬂames (e.g. candles). The appli-

ance could be irreparably damaged!

► Avoid direct sunlight. The appliance

could be irreparably damaged!

► This appliance must not be exposed to

rain. Protect the appliance against

moisture and the penetration of

liquids and objects into the housing.

Never submerge the appliance in

water and do not place objects ﬁlled

with liquids (such as vases) on the

appliance. The appliance could be

irreparably damaged!

► Operate the appliance only with

the supplied power adapter (type

HX06D-0900200-AB).

Functions

With this TV simulator you can simulate the ﬂicker patterns

of a switched-on television and so feign your presence to

potential burglars.

For this purpose 5 diﬀerent settings are available:

OFF 0: the appliance is switched oﬀ.

STS 12 B2 GB│IE│NI │ 9 ■

+2H: the LEDs switch on automatically at dusk and

then light up for 2 hours.

+4H: the LEDs switch on automatically at dusk and

then light up for 4 hours.

+6H: the LEDs switch on automatically at dusk and

then light up for 6 hours.

ON I: the LEDs light up in diﬀerent colours and combinations.

Setup

Select a suitable location for setting up the appliance. This

location must fulﬁl the following criteria:

― The TV Simulator may not be directly visible from

outdoors.

― The ﬂickering generated by the TV simulator must be

visible on the walls and/or ceiling from outdoors.

― A power socket must be easily accessible.

― The TV Simulator must be installed such that it can be

inﬂuenced by the twilight. This means that it must be

able to detect light from outside!

― The TV Simulator may not be located near a window

which could be well lit from outdoors, such as on a

busy street or next to street lights.

― There should be no additional time-controlled light

source in the room, e.g. a night light.

♦ Place the appliance on a ﬁrm and ﬂat surface so that it

is stable and secure. To help prevent it from tipping over,

you can secure the stand with the adhesive strips.

CAUTION - PROPERTY DAMAGE

► Do not use the adhesive strips to hang the appliance on

a wall! The appliance may fall down and be irreparably

damaged!

STS 12 B2

■ 10 │ GB│IE│NI

♦ Align the light surface  so that the ﬂicker is visible on

the walls and/or ceiling.

♦ Connect the power adapter  with the appliance by

inserting the barrel connector  into the plug socket  at

the rear side of the appliance. If required, route the power

cable through the cable conduit  on the appliance.

♦ Connect the power adapter  into a power socket.

NOTE

► It is best to check the location and alignment of the

appliance in the dark from outdoors and through the

window. Only in this way can you assess whether the

appliance is aligned so that it appears as if someone

is watching television inside.

If necessary, realign the appliance.

Wall mounting

RISK OF ELECTRIC SHOCK!

Ensure that there are no power cables or other conduits

or pipes in the wall at the location where you intend

to bore the holes for the wall holder. It would be a

potentially fatal risk to bore into a current carrying

electric cable!

Select a suitable mounting location for the appliance:

― The TV Simulator may not be directly visible from outdoors.

― The ﬂickering generated by the TV simulator must be

visible on the walls and/or ceiling from outdoors.

― A power socket must be easily accessible.

― The TV Simulator must be installed such that it can be

inﬂuenced by the twilight. This means that it must be able

to detect light from outside!

― The TV Simulator may not be located near a window

which could be well lit from outdoors, such as on a

busy street or next to street lights.

STS 12 B2 GB│IE│NI │ 11 ■

― There should be no additional time-controlled light

source in the room, e.g. a night light.

♦ Remove the stand by bending it slightly apart and then

pull the restraints out of the mountings.

♦ Drill two holes with a spacing of about 52 mm. Use

the stand to mark the holes: the spacing will thus be

measured correctly. The boreholes must be suitable for

8 mm wall plugs.

♦ Insert the supplied plugs into the holes and screw the

stand ﬁrmly down through the holes for wall mounting 

using the supplied screws.

♦ Push the TV Simulator back onto the stand. Ensure that

the two cross-shaped restraints engage correctly with the

mountings.

CAUTION - PROPERTY DAMAGE

► Before you connect the appliance to the power supply,

check to ensure that the required input voltage as

given on the type plate tallies with that for the intended

power source.

► Check to ensure that the cable for the power adapter 

is not damaged and that it does not lead over hot

surfaces and/or sharp edges, otherwise it could be

damaged.

► Ensure that the cable for the power adapter  is not

over-taut or kinked.

♦ Connect the power adapter  with the appliance by

inserting the barrel connector  into the plug socket 

at the rear side of the appliance.

♦ Align the light surface  so that the ﬂicker is visible on

the walls and/or ceiling.

STS 12 B2

■ 12 │ GB│IE│NI

♦ Connect the power adapter  into a power socket.

NOTE

► It is best to check the location and alignment of the

appliance in the dark from outdoors and through the

window. Only in this way can you assess whether the

appliance is aligned so that it appears as if someone

is watching television inside.

If necessary, realign the appliance.

Operation

♦ When it gets dark early, for example, in the winter

months, set switch  to „ +6H“. 3 green LEDs light

up immediately. The appliance becomes active at dusk

and, for 6 hours, simulates the ﬂickering of a television.

After 6 hours the appliance switches itself oﬀ, except

for the 3 green LEDs.

As soon as it is dusk again, the appliance switches

back on for 6 hours.

To switch your appliance oﬀ again, you need to slide

switch  to the position “OFF“.

NOTE

► In the case of exposure to light (> ca. 30 lux) the TV

Simulator also switches oﬀ before the 6 hours have

lapsed.

♦ Set the switch to „ +4H“, for example, during

autumn and spring. 2 blue LEDs light up immediately.

The appliance becomes active at dusk and, for 4 hours,

simulates the ﬂickering of a television. After 4 hours the

appliance switches itself oﬀ, except for the 2 blue LEDs.

As soon as it is dusk again, the appliance switches back

on for 4 hours.

STS 12 B2 GB│IE│NI │ 13 ■

♦ To switch your appliance oﬀ again, you need to slide

switch  to the position “OFF“.

NOTE

► In the case of exposure to light (> ca. 30 lux) the TV

Simulator also switches oﬀ before the 4 hours have

lapsed.

♦ When it gets dark late, for example, in the summer

months, set switch  to „ +2H“. A red LED lights

up immediately. The appliance becomes active at

dusk and, for 2 hours, simulates the ﬂickering of a

television. After 2 hours the appliance switches itself

oﬀ, except for the red LED.

As soon as it is dusk again, the appliance switches

back on for 2 hours.

To switch your appliance oﬀ again, you need to slide

switch  to the position “OFF“.

NOTE

► In the case of exposure to light (> ca. 30 lux) the TV

Simulator also switches oﬀ before the 2 hours have

lapsed.

♦ Place switch  at “ON” to have the appliance perma-

nently switched on. To switch your appliance oﬀ , you

need to slide switch  to the position “OFF”.

NOTE

► Neither this TV Simulator, nor any other simulation

systems, can guarantee that you will not be burgled.

However, the TV Simulator conveys to potential burglars

that someone is at home and watching TV.

► In every case, we recommend good door locks and anti-

burglar aids, such as security doors and windows, as well

as an alarm system, to deter burglars from breaking into

your home.

STS 12 B2

■ 14 │ GB│IE│NI

Cleaning

CAUTION - PROPERTY DAMAGE

► Ensure that, when cleaning it, no moisture can penetrate

into the appliance, so as to avoid irreparable damage

to it.

► Ensure that you remove the power adapter  from the

power socket before cleaning the appliance.

♦ Clean the surfaces of the appliance and the power

adapter  with a soft, dry cloth.

♦ For stubborn soiling, use a damp cloth and possibly

add a mild detergent to it.

♦ Ensure that the appliance and the power adapter 

are completely dry before using them again.

Storage

Should you decide not use the appliance for an extended

period, disconnect it from the power supply and store it in a

clean and dry location away from direct sunlight. If the ap-

pliance is mounted to the wall, disconnect it from the power

socket.

Disposal of the appliance

Do not dispose of the appliance in your

normal domestic waste. This product is

subject to the provisions of European

Directive 2012/19/EU-WEEE (Waste

Electrical and Electronic Equipment).

Dispose of the appliance through an approved disposal

centre or at your community waste facility. Please observe

the currently applicable regulations. In case of doubt, please

contact your waste disposal centre.

STS 12 B2 GB│IE│NI │ 15 ■

Appendix

Kompernass Handels GmbH warranty

Dear Customer,

This appliance has a 3-year warranty valid from the date of

purchase. If this product has any faults, you, the buyer, have

certain statutory rights. Your statutory rights are not restricted

in any way by the warranty described below.

Warranty conditions

The validity period of the warranty starts from the date of

purchase. Please keep your original receipt in a safe place.

This document will be required as proof of purchase.

If any material or production fault occurs within three years of

the date of purchase of the product, we will either repair or

replace the product for you at our discretion. This warranty

service is dependent on you presenting the defective appliance

and the proof of purchase (receipt) and a short written de-

scription of the fault and its time of occurrence.

If the defect is covered by the warranty, your product will

either be repaired or replaced by us. The repair or replace-

ment of a product does not signify the beginning of a new

warranty period.

Warranty period and statutory claims for defects

The warranty period is not prolonged by repairs eﬀected under

the warranty. This also applies to replaced and repaired

components. Any damage and defects present at the time

of purchase must be reported immediately after unpacking.

Repairs carried out after expiry of the warranty period shall

be subject to a fee.

STS 12 B2

■ 16 │ GB│IE│NI

Scope of the warranty

This appliance has been manufactured in accordance with

strict quality guidelines and inspected meticulously prior to

delivery.

The warranty covers material faults or production faults. The

warranty does not extend to product parts subject to normal

wear and tear or fragile parts such as switches, batteries,

baking moulds or parts made of glass.

The warranty does not apply if the product has been dam-

aged, improperly used or improperly maintained. The direc-

tions in the operating instructions for the product regarding

proper use of the product are to be strictly followed. Uses

and actions that are discouraged in the operating instruc-

tions or which are warned against must be avoided.

This product is intended solely for private use and not for

commercial purposes. The warranty shall be deemed void

in cases of misuse or improper handling, use of force and

modiﬁcations / repairs which have not been carried out by

one of our authorised Service centres.

STS 12 B2 GB│IE│NI │ 17 ■

Warranty claim procedure

To ensure quick processing of your case, please observe the

following instructions:

■ Please have the till receipt and the item number (e.g. IAN

12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate, an engrav-

ing on the front page of the instructions (bottom left), or

as a sticker on the rear or bottom of the appliance.

■ If functional or other defects occur, please contact the

service department listed either by telephone or by

e-mail.

■ You can return a defective product to us free of charge to

the service address that will be provided to you. Ensure

that you enclose the proof of purchase (till receipt) and

information about what the defect is and when it occurred.

You can download these instructions along with

many other manuals, product videos and software

on www.lidl-service.com.

Seite laden ...

Lidl STS 12 B2 Operating Instructions Manual

Lidl STS 12 B2 Operating Instructions Manual

in anderen Sprachen

Sonstige Unterlagen