LIVARNO 110587 Bedienungsanleitung

V 1.1

English ........................................................................................................................ 2

Polski ....................................................................................................................... 15

Magyar .................................................................................................................... 27

Česky ....................................................................................................................... 39

Slovenčina ................................................................................................................ 52

Deutsch ..................................................................................................................... 64

LIVARNO LUX LLES B2

2 - English

Content

Introduction ................................................................................................................ 3

Intended use ............................................................................................................... 3

Supplied items ............................................................................................................ 3

Technical data ............................................................................................................ 4

Safety instructions ...................................................................................................... 5

Copyright ................................................................................................................... 6

Prior to use ................................................................................................................. 6

The correct installation location ...................................................................................................................... 7

Required tools .................................................................................................................................................. 7

Prior to installation ........................................................................................................................................... 7

Installation ........................................................................................................................................................ 8

First use ...................................................................................................................... 9

Aligning the motion sensor ............................................................................................................................. 9

Setting light time (TIME) .................................................................................................................................. 9

Adjusting sensor sensitivity (SENS) ................................................................................................................ 9

Adjusting light sensitivity (LUX) ....................................................................................................................... 9

Cleaning / maintenance ............................................................................................ 10

Troubleshooting ....................................................................................................... 11

Environmental and disposal information .................................................................. 11

Conformity ............................................................................................................... 12

Warranty and servicing advice ................................................................................. 13

LIVARNO LUX LLES B2

English - 3

Introduction

Thank you for purchasing a LIVARNO LUX product.

Intended use

This energy-saving outdoor spotlight is not designed for commercial application. It is suitable for indoor

and outdoor use. The 23 watt energy-saving light bulb (10) provides good illumination. The motion sensor

detects movements and the energy-saving outdoor spotlight automatically switches itself on and off as a

result. This device meets all relevant norms and standards in conjunction with CE conformity. In the event

of any modification to the energy-saving outdoor spotlight that was not approved by the manufacturer,

compliance with these standards is no longer guaranteed.

Supplied items

 Energy-saving outdoor spotlight LLES B2

 Installation materials (2 screws and 2 plugs)

 Operating instructions and safety instructions

These operating instructions have a fold-out cover. The energy-saving outdoor spotlight is illustrated with

numbers on the inside cover. The numbers indicate the following:

1 Screw (front pane)

2 Screw (wall bracket)

3 Cable junction box

4 Cable bushing

5 Screw connection (cable bushing)

6 Wall bracket

7 Locking screw

8 Motion sensor

9 Front pane

10 Energy-saving light bulb (not dimmable)

11 Power cable (not supplied / home connection)

12 Screw terminal

13 LUX control

14 SENS control

15 TIME control

LIVARNO LUX LLES B2

4 - English

Technical data

Spotlight:

Brand: LIVARNO LUX

Model designation: LLES B2

Operating voltage: 220 – 240V

~

, 50Hz

Protection class: I (with earth conductor)

Protection rating: IP44 (splashing water protection category)

Dimensions (W x H x D): approx. 217 x 138.5 x 103 mm

Weight: approx. 1,035g (without light bulb)

Safety tested by:

Energy-saving light bulb:

Light bulb: Energy-saving light bulb E27 (only spiral bulb)

Energy efficiency class: A

Service life: approx. 8000 hours / approx. 8000 switching cycles

Luminous flux: 1300lm +/-5%

Power: 23 watts

Colour temperature: 6400K +/-10%

Motion sensor:

Sensor detection angle: 180° max.

Detection range: max. 12m (can be set via control dial)

Light sensitivity: can be set via control dial

Mechanical swivelling: approx. 150° horizontal / approx. 180° vertical

Light time: approx. 1 min +/- 15 sec to 15 min +/- 1.5 min

The technical data and design may be changed without notification.

LIVARNO LUX LLES B2

English - 5

Safety instructions

Before using this device for the first time, please read the following instructions carefully and take note of

the safety warnings, even if you are familiar with the use of electronic devices. Store these operating

instructions in a safe place for future reference. If you sell or pass on the device to someone else, be sure

to always include these operating instructions as they are an integral part of the device.

WARNING! This symbol indicates important information for safe operation of the

energy-saving outdoor spotlight and the safety of the user. Disregarding this

information can lead to material damage and/or health hazards and even death.

Fire hazard: Attach the energy-saving outdoor spotlight at a distance of at least

0.5m from illuminated materials. Excessive heat generation can cause a fire.

Any cracked protective cover must be replaced.

The energy-saving outdoor spotlight has an earth conductor. The earth conductor

(yellow/green) must be connected to the indicated terminal.

Electrical devices do not belong in the hands of children. Never allow children to use electrical

devices unsupervised. Children may not recognise potential risks. Always keep plastic packaging

away from children. It poses a suffocation risk.

If smoke is produced, or there are any unusual sounds or smells, turn the device off immediately.

In such cases, the device should not be used until it has been inspected by authorised service

personnel. Never inhale smoke from a potential device fire. If you have inhaled smoke, however,

consult a doctor. The inhalation of smoke can be harmful.

The housing of the energy-saving outdoor spotlight must not be damaged. There is a risk of an

electric shock if the housing is damaged.

Do not use the energy-saving outdoor spotlight in potentially explosive environments which

contain flammable gases, vapours or dust. It poses a risk of explosion.

Never open the housing of the energy-saving outdoor spotlight except to change the energy-

saving bulb. The circuit must be disconnected during all work on the energy-saving outdoor

spotlight, even when changing the light bulb! There is a risk of an electric shock if the housing is

open.

LIVARNO LUX LLES B2

6 - English

You must not hang any objects on the energy-saving outdoor spotlight. The housing is not

designed to carry loads. Otherwise, the energy-saving outdoor spotlight could be damaged.

Never use such optical instruments as a magnifying glass to look directly into the light beam. This

can lead to eye injuries. In the event of a suspected eye injury, consult a doctor immediately.

Copyright

All information contained in these instructions is subject to copyright and is provided for information

purposes only. It is only permitted to copy or duplicate data and information with the express and written

consent of the author. This also includes commercial use of the content and data. The text and illustrations

are based on the state of the art at the time of printing. Subject to change without notice.

Prior to use

Remove the energy-saving outdoor spotlight and the installation materials from the packaging.

Check the energy-saving outdoor spotlight for signs of damage. If damaged, the energy-saving outdoor

spotlight must not be used.

Only use energy-saving spiral light bulbs with E27 base and a maximum power of 23 watts!

Please note:

The supplied energy-saving light bulb is not dimmable. Do not use the energy-saving outdoor

spotlight with the supplied light bulb in circuits with dimmers.

The energy-saving light bulb (10) is stored within

the spotlight so that it can be transported safely.

Loosen the 2 screws (1) with a Phillips screwdriver

and carefully tilt the front pane (9) upwards.

Remove the packaging with the energy-saving

light bulb (10). Open the packaging, remove the

energy-saving light bulb (10) and screw it into the

socket in a clockwise direction. When doing so,

handle the energy-saving light bulb (10) by its

base and not by its glass body. The bulb should

only ever be handled with a cloth. Close the front

pane (9) downwards now and tighten the 2

screws (1) again.

LIVARNO LUX LLES B2

English - 7

The correct installation location

Select the installation location carefully and prepare well for the installation.

 Place all individual parts, required tools and installation material so they are well arranged and ready

to hand.

 The energy-saving outdoor spotlight may be mounted only on stable substrates, for example,

brickwork.

 Do not install the energy-saving outdoor spotlight above a heat source or in the immediate vicinity of

other light sources. When selecting the installation location, also pay attention to the illustration [D] on

the inside cover.

 Select the installation location so that the energy-saving outdoor spotlight is protected against wind,

rain and dirt.

 Find out in advance which installation material is suitable for the installation location you selected.

Suitable installation material for concrete is included with the energy-saving outdoor spotlight.

Required tools

The following tools are not supplied. This list can be used for orientation. The exact nature of the required

tools depends on the individual on-site conditions.

 Ladder

 Voltage tester

 Spirit level, folding ruler, pencil

 Drill with drill bits

 Phillips screwdriver, flat-bladed screwdriver

 Spanner, combination pliers, side cutter

Prior to installation

The installation must be performed only by an authorised electrician!

The circuit must be disconnected during the installation!

When drilling the holes, make sure that no cables or pipes in the wall are damaged.

LIVARNO LUX LLES B2

8 - English

 Before installation, familiarise yourself with the individual parts of the energy-saving outdoor spotlight

as well as the text and illustrations of these operating instructions and comply with them.

 Make sure that the cable to which the energy-saving outdoor spotlight is to be connected is not live.

To ensure that this is the case, remove the appropriate circuit fuse from your fuse box or switch the

fuse to the "0" position.

 Make sure that the cable is not live using a voltage tester!

Installation

 Detach the wall bracket (6) from the energy-saving outdoor spotlight by removing the 2 screws (2)

with a Phillips screwdriver. Note that the wall bracket (6) is attached on both sides with a screw (2), a

spring washer and a flat washer. Keep these parts safe until you are ready to assemble them.

 Use the wall bracket (6) as a template to mark the two holes.

 Then drill the two holes and attach the wall bracket (6) using the supplied wall plugs and screws or,

depending on the installation location, using other suitable plugs and screws.

 Open the cable junction box (3) by loosening the four screws using a Phillips screwdriver and

removing the cover.

 Loosen the 2 screws on the strain relief within the cable junction box (3) with a Phillips screwdriver

only to the extent that the power cable (11) can be subsequently fed through it.

 Loosen the screw connection (5) of the cable bushing (4), but do not completely unscrew it.

 Remove approx. 5 to 8cm of the sheath of the power cable (11).

 First, route the power cable (11) through the screw connection (5) and the cable bushing (4), and

then through the strain relief in the cable junction box (3). When routing the power cable (11)

through the cable bushing (4), an internal rubber seal must be penetrated. A slight resistance may

thus be felt.

 Fix the power cable (11) by tightening the 2 screws on the strain relief within the cable junction box

(3). The end of the cable sheath must be in the strain relief for this purpose. Do not clamp the

individual wires!

 Then tighten the previously loosened screw connection (5) of the cable bushing (4) in a clockwise

direction. This ensures the sealing of the power cable (11).

 Connect the stripped wire ends of the power cable (11) using the screw terminal (12). Make sure that

the individual wires of the power cable (11) are connected correctly. Also pay attention in this context

to the illustration [B] on the inside cover.

Wire Symbol Designation

Black or brown L Phase

Blue N Neutral

Yellow/green Earth conductor

LIVARNO LUX LLES B2

English - 9

 Close the cable junction box (3) by screwing the cover again tightly with the four screws that you

previously removed. A rubber seal which is integrated in the cover ensures the sealing of the cable

junction box (3). Ensure that the rubber seal lies correctly in the groove provided in the cover.

 Then attach the energy-saving outdoor spotlight to the wall bracket (6). To do so, use the previously

removed screws (2) and flat washers.

 Switch on the circuit.

First use

Aligning the motion sensor

Make sure that no movements that should not be detected (for example, on the pavements or

streets) occur in the detection range of the motion sensor (8).

It is best if you set the light sensitivity of the motion sensor (8) during the lighting conditions when

the energy-saving outdoor spotlight is supposed to be active.

 Align the motion sensor (8) so that it can capture the desired range as well as possible. The view must

not be obstructed by objects or anything else.

 You can align the motion sensor (8) horizontally by turning it.

 To align the motion sensor (8) vertically, you must first loosen the locking screw (7). If the motion sensor

(8) is located in the desired position, you must tighten the locking screw (7) again.

Setting light time (TIME)

You use the TIME control (15) at the bottom of the motion sensor (8) to set the light time (approx. 1 min to

15 min). Turn the TIME control (15) clockwise (+ direction) to increase the light time or anti-clockwise (-

direction) to reduce the light time.

Adjusting sensor sensitivity (SENS)

You use the SENS control (14) at the bottom of the motion sensor (8) to adjust the sensor sensitivity. Turn

the SENS control (14) clockwise (+ direction) to increase the sensitivity or anti-clockwise (- direction) to

reduce the sensitivity. The higher the sensitivity, the greater the detection range (12 metres at the most).

Adjusting light sensitivity (LUX)

You use the LUX control (13) at the bottom of the motion sensor (8) to adjust the light sensitivity. Here, you

set the lighting conditions to which the twilight sensor responds and thus the energy-saving outdoor

spotlight is switched on or off.

LIVARNO LUX LLES B2

10 - English

Turn the LUX control (13) clockwise ( direction) so that the motion sensor (8) responds to brighter

lighting conditions.

Turn the LUX control (13) anti-clockwise ( direction) so that the motion sensor (8) responds to darker

lighting conditions.

Cleaning / maintenance

Maintenance

The energy-saving outdoor spotlight does not contain any parts that require maintenance.

Replacing the light bulb

The circuit must be disconnected during all work on the energy-saving outdoor spotlight, even

when changing the light bulb! There is a risk of an electric shock!

Only use energy-saving spiral light bulbs with E27 base and a maximum power of 23 watts!

Loosen the 2 screws (1) with a Phillips screwdriver

and carefully tilt the front pane (9) downwards.

Unscrew the old/defective energy-saving light

bulb (10) anti-clockwise out of the socket. Then

screw a new energy-saving light bulb of the same

design (see "Technical data" section) clockwise

into the socket. When doing so, handle the energy-

saving light bulb (10) by its base and not by its

glass body. The bulb should only ever be handled

with a cloth. Close the front pane (9) upwards

now and tighten the 2 screws (1) again.

Switch on the circuit again.

LIVARNO LUX LLES B2

English - 11

Cleaning

The circuit must be disconnected during all work on the energy-saving outdoor spotlight, even

when cleaning it! There is a risk of an electric shock!

Ensure that no liquid can penetrate the housing of the energy-saving outdoor spotlight. There is

a risk of an electric shock.

To clean the energy-saving outdoor spotlight, use a soft, dry cloth and never use any solvent or cleaner

that would corrode the plastic materials. Use a slightly damp cloth for more stubborn dirt.

Troubleshooting

The light does not switch itself on

 The motion sensor (8) is not aligned correctly. Correct the alignment.

 The energy-saving light bulb (10) is faulty. Replace it.

 The electrical connection is faulty. Get an authorised electrician to check the electrical connection.

The light switches on and off quickly

 The sensor is disturbed by extraneous light or bright reflective surfaces. Remove the extraneous light

source or the disturbing surfaces.

The light does not switch off

 Persons or objects are within the detection range of the motion sensor (8). Remove them.

 The energy-saving outdoor spotlight moves in the wind, which continually triggers the motion sensor

(8). Attach the energy-saving outdoor spotlight only to a stable installation location.

Environmental and disposal information

When the crossed out wheelie bin symbol appears on a product, this indicates that the

product is subject to the European Directive 2012/19/EU. All old electrical and

electronic devices must be separated from normal household waste and disposed of at

designated state facilities. The light bulb must also be disposed of properly.

The device must not be disposed of with the household waste or bulky waste. You can

obtain information regarding collection points or collection times via your local

administration or local disposal services.

The device is operated with a compact fluorescent bulb. This contains complex electronic components and

must not be disposed of in normal household waste. You can obtain information regarding collection

points or collection times via your local administration or local disposal services.

LIVARNO LUX LLES B2

12 - English

Dispose of the packaging in an environmentally compatible manner. Cardboard can be put out for

municipal paper collections or brought to public collection points for recycling. Films and plastic used for

packaging the device are collected by your local disposal services and disposed of in an environmentally

compatible manner.

Conformity

This device meets the basic requirements and other relevant regulations of the EMC

Directive 2004/108/EC, the Low Voltage Directive 2006/95/EC, the ErP Directive

2009/125/EC and the RoHS Directive 2011/65/EU. The Declaration of

Conformity can be found at the end of these operating instructions.

LIVARNO LUX LLES B2

English - 13

Warranty and servicing advice

Warranty of TARGA GmbH

Dear Customer,

This device is sold with three years warranty from the date of purchase. In the event of product defects,

you have legal rights towards the seller. These statutory rights are not restricted by our warranty as

described below.

Warranty conditions

The warranty period commences upon the date of purchase. Please keep the original receipt in a safe

place as it is required as proof of purchase. If any material or manufacturing faults occur within three

years of purchase of this product, we will repair or replace the product free of charge as we deem

appropriate.

Warranty period and legal warranty rights

The warranty period is not extended in the event of a warranty claim. This also applies to replaced and

repaired parts. Any damage or defects discovered upon purchase must be reported immediately when the

product has been unpacked. Any repairs required after the warranty period will be subject to charge.

Scope of warranty

The device was carefully manufactured in compliance with stringent quality guidelines and subjected to

thorough testing before it left the works. The warranty applies to material and manufacturing faults. This

warranty does not cover product components which are subject to normal wear and which can therefore

be regarded as wearing parts, or damage to fragile components such as switches, rechargeable batteries

or components made of glass. This warranty is void if the product is damaged, incorrectly used or

serviced. To ensure correct use of the product, always comply fully with all instructions contained in the

user manual. The warnings and recommendations in the user manual regarding correct and incorrect use

and handling of the product must always be observed and complied with. The product is solely designed

for private use and is not suitable for commercial applications. The warranty is rendered void in the event

of incorrect handling and misuse, if it is subjected to force, and also if any person other than our

authorised service technicians interfere with the device. No new warranty period commences if the

product is repaired or replaced.

Submitting warranty claims

To ensure speedy handling of your complaint, please note the following:

- Before using your product for the first time, please read the enclosed documentation carefully.

Should any problems arise which cannot be solved in this way, please call our hotline.

- Always have your receipt, the product article number as well as the serial number (if available)

to hand as proof of purchase.

- If it is not possible to solve the problem on the phone, our hotline support staff will initiate further

servicing procedures depending on the fault.

LIVARNO LUX LLES B2

14 - English

Service

Phone: 0207 – 36 50 744

E-Mail: [email protected]

Phone: 01 – 242 15 83

E-Mail: [email protected]

Phone: 800 – 62 175

E-Mail: [email protected]

Phone: 800 – 92 496

E-Mail: [email protected]

IAN: 110587

Manufacturer

Please note that the following address is not a service address. First contact the service point stated above.

TARGA GmbH

Coesterweg 45

59494 SOEST

GERMANY

LIVARNO LUX LLES B2

Polski - 15

Spis treści

Wstęp ....................................................................................................................... 16

Użytkowanie zgodne z przeznaczeniem .................................................................. 16

Zakres dostawy ....................................................................................................... 16

Dane techniczne ....................................................................................................... 17

Wskazówki bezpieczeństwa .................................................................................... 18

Prawa autorskie ...................................................................................................... 19

Przed uruchomieniem ............................................................................................... 19

Odpowiednie miejsce montażu .................................................................................................................. 20

Potrzebne narzędzia .................................................................................................................................... 20

Przed montażem ........................................................................................................................................... 20

Montaż.......................................................................................................................................................... 21

Uruchomienie ........................................................................................................... 22

Ustawienie czujnika ruchu ........................................................................................................................... 22

Ustawienie czasu świecenia (TIME) ............................................................................................................ 22

Ustawienie czułości czujnika (SENS) .......................................................................................................... 22

Ustawienie czułości na światło (LUX) .......................................................................................................... 22

Konserwacja / czyszczenie....................................................................................... 23

Rozwiązywanie problemów .................................................................................... 24

Wskazówki dotyczące ochrony środowiska i prawidłowego usuwania .................. 24

Zgodność.................................................................................................................. 25

Informacje na temat gwarancji i serwisowania ........................................................ 25

LIVARNO LUX LLES B2

16 - Polski

Wstęp

Dziękujemy za zakup produktu LIVARNO LUX.

Użytkowanie zgodne z przeznaczeniem

Energooszczędna lampa zewnętrzna nie jest przeznaczona do użytku komercyjnego. Nadaje się ona do

pracy na otwartej przestrzeni i w pomieszczeniach. Energooszczędna świetlówka (10) o mocy 23 W

zapewnia dobre oświetlenie. Czujnik ruchu rejestruje ruch i automatycznie włącza oraz wyłącza

energooszczędną lampę zewnętrzną. Niniejsze urządzenie spełnia wymagania wszystkich odnośnych

norm i dyrektyw, związanych ze zgodnością CE. W przypadku nieuzgodnionych z producentem

modyfikacji energooszczędnej lampy zewnętrznej nie można zagwarantować spełnienia wymagań tych

norm.

Zakres dostawy

 Energooszczędna lampa zewnętrzna LLES B2

 Materiały montażowe (2 wkręty i 2 kołki rozporowe)

 Instrukcja obsługi i wskazówki bezpieczeństwa

Niniejsza instrukcja ma odchylaną okładkę. Na wewnętrznej stronie odchylanej okładki jest

przedstawiona energooszczędna lampa zewnętrzna wraz z oznaczeniami liczbowymi. Liczby mają

następujące znaczenie:

1 Śruba (szyba przednia)

2 Śruba (uchwyt ścienny)

3 Puszka przyłączeniowa kabla

4 Przepust kablowy

5 Zacisk gwintowany przepustu kablowego

6 Uchwyt ścienny

7 Śruba ustalająca

8 Czujnik ruchu

9 Szyba przednia

10 Świetlówka energooszczędna (bez możliwości ściemniania)

11 Kabel zasilający (nie wchodzi w zakres dostawy / przyłącze domowe)

12 Kostka przyłączeniowa

13 Regulator LUX

14 Regulator SENS

15 Regulator TIME

LIVARNO LUX LLES B2

Polski - 17

Dane techniczne

Lampa:

Marka: LIVARNO LUX

Nazwa modelu: LLES B2

Napięcie zasilania: 220 – 240 V

~

, 50 Hz

Klasa ochrony: I (przy podłączeniu z przewodem ochronnym)

Stopień ochrony: IP44 (bryzgoszczelna)

Wymiary (S x W x G): ok. 217 x 138,5 x 103 mm

Masa: ok. 1035 g (bez świetlówki)

Sprawdzone bezpieczeństwo:

Świetlówka energooszczędna:

Źródło światła: świetlówka energooszczędna E27 (tylko spiralna)

Klasa wydajności energetycznej: A

Żywotność: ok. 8000 godzin / ok. 8000 cykli włączenia

Strumień świetlny: 1300 lm +/-5%

Moc: 23 W

Temperatura barwowa: 6400 K +/-10%

Czujnik ruchu:

Kąt widzenia czujnika: maks. 180°

Zasięg czujnika: maks. 12 m (ustawiany za pomocą regulatora

obrotowego)

Czułość na światło: ustawiana za pomocą regulatora obrotowego

Regulacja położenia (mechaniczna): ok. 150° w poziomie / ok. 180° w pionie

Czas świecenia: od ok. 1 min +/- 15 s do 15 min +/- 1,5 min

Zastrzegamy możliwość zmian danych technicznych i konstrukcyjnych bez wcześniejszego uprzedzenia.

LIVARNO LUX LLES B2

18 - Polski

Wskazówki bezpieczeństwa

Przed pierwszym użyciem urządzenia prosimy dokładnie zapoznać się z poniższymi instrukcjami. Należy

stosować się do wszystkich ostrzeżeń o zagrożeniach, nawet jeśli obsługa urządzeń elektronicznych jest

Ci dobrze znana. Niniejszą instrukcję obsługi należy starannie przechowywać do wykorzystania w

przyszłości. Jeżeli odstępujesz lub użyczasz urządzenie innej osobie, przekaż także tę instrukcję obsługi

– jest ona częścią składową urządzenia.

OSTRZEŻENIE! Ten symbol oznacza ważne wskazówki w sprawie bezpiecznej

eksploatacji zewnętrznej lampy energooszczędnej i ochrony użytkownika.

Nieprzestrzeganie może spowodować szkody materialne i/lub zagrożenie dla

zdrowia ze śmiercią włącznie.

Niebezpieczeństwo pożaru: zewnętrzną lampę energooszczędną należy

zamontować w odległości co najmniej 0,5 m od oświetlanych przedmiotów.

Nadmierne wydzielanie ciepła może spowodować pożar.

Każdą pękniętą osłonę należy wymienić.

Zewnętrzna lampa energooszczędna jest wyposażona w przyłącze przewodu

ochronnego. Przewód ochronny (żółto-zielony) musi być podłączony do tak

oznaczonego zacisku.

Urządzenia elektryczne należy trzymać poza zasięgiem dzieci. Nigdy nie należy pozwalać

dzieciom używać urządzeń elektrycznych bez nadzoru. Dzieci nie zawsze mogą prawidłowo

rozpoznać ewentualne zagrożenia. Folie z opakowań należy także przechowywać poza

zasięgiem dzieci. Istnieje niebezpieczeństwo uduszenia.

W razie stwierdzenia tworzenia się dymu, zauważenia dziwnych odgłosów lub zapachów

natychmiast wyłączyć urządzenie. W takich przypadkach urządzenia nie wolno dalej używać,

dopóki nie zostanie ono sprawdzone przez specjalistę. W żadnym przypadku nie wolno

wdychać dymu z możliwego pożaru urządzenia. O ile mimo to doszło do wdychania dymu,

należy udać się do lekarza. Wdychanie dymu może być szkodliwe dla zdrowia.

Nie wolno uszkodzić obudowy zewnętrznej lampy energooszczędnej. Przy uszkodzonej

obudowie istnieje zagrożenie dla życia na skutek porażenia prądem elektrycznym.

Nigdy nie używać zewnętrznej lampy energooszczędnej w przestrzeniach zagrożonych

wybuchem, w których znajdują się łatwopalne płyny, gazy lub pyły. Istnieje niebezpieczeństwo

eksplozji.

Nigdy nie otwierać obudowy zewnętrznej lampy energooszczędnej, za wyjątkiem wymiany

świetlówki. Podczas wszystkich prac przy zewnętrznej lampie energooszczędnej, w tym także

przy wymianie świetlówki, obwód prądowy musi być rozłączony! Przy otwartej obudowie

istnieje zagrożenie porażenia prądem elektrycznym.

Seite laden ...

LIVARNO 110587 Bedienungsanleitung

LIVARNO 110587 Bedienungsanleitung

in anderen Sprachen

Verwandte Papiere

Sonstige Unterlagen