Update to the
QMS
®
magicolor
®
LX
Printer User’s Guide
To update your QMS magicolor LX Printer User’s Guide, please
replace pages 2-25 through 2-26 and pages 6-13 through 6-16 with
the pages in this package.
1800414-001A
2. Hold the cleaning pad by its tab and place the white side
against the orange roller closest to the green felt strip. Align
the center rib of the cleaning pad with the triangle on the green
felt strip.
3. Keep the white side of the pad touching the orange roller
closest to the green felt strip as you press the pad forward and
down into the slot under the green felt strip (fig. 2.17). It’s in
place when it clips securely into the slot with the white pad
touching the orange roller.
CAUTION: The $1000 fuser unit will be damaged if the cleaning
pad is not replaced each time the oil bottle is replaced. This type of
damage is not covered under warranty or service contract. Both
parts are included in the same kit.
Fig. 2.17 Install the Cleaning Pad (front view)
Chapter 2
Initial Printer Setup 2-25
4. Snap the separator pawl unit closed (fig. 2.18).
Fig. 2.18 Close Separator Pawl Unit (front view)
Chapter 2
2-26 Initial Printer Setup
5. Locate the cleaning pad in the slot above the heat roller. Then,
while carefully avoiding the surface of the fuser unit, which
may be hot, grasp the pad by its center tab (towards the rear
of the unit), pull it out of the printer, and discard it (fig. 6.3).
6. Remove the new cleaning pad and the new oil bottle from their
protective bags.
CAUTION: The $1000 fuser unit will be damaged if the cleaning
pad is not replaced each time the oil bottle is replaced. This type of
damage is not covered under warranty or service contract. Both
parts are included in the same kit.
Fig. 6.3 Remove the Cleaning Pad
Chapter 6
Consumables and Preventative Maintenance 6-13
7. Hold the new cleaning pad by its tab and place the white side
against the orange roller closest to the green felt strip. Align
the center rib of the cleaning pad with the triangle on the green
felt strip.
8. Keep the white side of the pad touching the orange roller
closest to the green felt strip as you press the pad forward and
down into the slot under the green felt strip. It’s in place when
it clips securely into the slot with the white pad touching the
orange roller.
9. Snap the separator pawl unit closed.
10. Pull open the spring latch on the outer edge of the oil bottle
retainer, and lift the retainer up and toward the center of the
printer (fig. 2.19).
NOTE: Normally, a little oil remains in the fuser slot in which
the oil bottle rests, and the spout of the oil bottle has a seal to
prevent oil from spilling while you remove or install a bottle
Chapter 6
6-14 Consumables and Preventative Maintenance
on the pin in the fuser slot. However, if oil accidentally spills
beyond that slot, use a clean, dry, lint-free cloth or some cotton
swabs to wipe up the excess.
11. Grasp the top tab on the oil bottle, then lift the bottle out of
the printer, and discard it.
NOTE: If you are replacing an oil bottle after a move, remove
and discard the wadded paper towel from the place normally
occupied by the oil bottle.
12. Hold the new oil bottle, spout end down, bottle label toward
the front of the printer, over its slot in the fuser unit (fig. 2.19).
13. Lower the bottle into place, making sure the spout on the
bottom aligns with the pin in the fuser slot. The bottle is
positioned correctly when it fits snugly into the slot and is
flush with the fuser unit.
14. Close and latch the oil bottle retainer.
15. Close the paper exit unit.
16. Replace the printer’s top cover and turn on the main power
switch.
Replacing the Waste Toner Pack
This section covers replacing the waste toner pack in your printer.
The pack collects excess toner from the printing process and should
be replaced when the window on the control panel displays the
message CHECK WASTE TONER. Illustrations for many of the
steps described in this section are in chapter 2, “Initial Printer
Setup.”
1. Open the waste toner cover by pushing the cover on the
top-right corner (fig. 2.22).
2. Remove the new waste toner pack from its protective bag and
assemble it according to the instructions accompanying it.
Chapter 6
Consumables and Preventative Maintenance 6-15
3. Gently tap the old waste toner pack on its side to settle the
toner down into the pack (fig. 6.4).
WARNING!
The toner is a highly combustible powder; never
burn it. Also, avoid inhaling loose toner or getting it around
your eyes; it can cause respiratory problems and eye irritation.
ACHTUNG!
Bei dem Toner handelt es sich um ein gefähr-
liches und leicht entzündliches Pulver; es darf deshalb niemals
mit offenem Feuer in Berührung kommen. Einatmen oder
Berührung mit Haut und Augen ist ebenfalls zu vermeiden, da
dies zu Beeinträchtigungen der Atemwege, Haut- oder Augen-
reizungen führen könnte.
4. Grasp the tab on the top edge of the old waste toner pack, and
pull it out of the printer.
Fig. 6.4 Tap the Waste Toner Pack
Chapter 6
6-16 Consumables and Preventative Maintenance
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
in anderen Sprachen
- English: QMS Magicolor LX User manual
Verwandte Papiere
Sonstige Unterlagen
-
KYOCERA ECOSYS FS-9130DN Benutzerhandbuch
-
Tektronix PHASER 740 Replacement Manual
-
-
Utax C 08 Bedienungsanleitung
-
-
Xerox PHASER 780 Bedienungsanleitung
-
-
Hitachi DDS 40 Getting Started Manual
-