Silvercrest KH 2299 Bedienungsanleitung

KH 2299

KOMPERNASS GMBH

BURGSTRASSE 21 ⋅ D-44867 BOCHUM

www.kompernass.com

ID-Nr.: KH 2299-1/10-V4

3

Undercupboard Radio

Operating manual

Uppoasennettava radio

Käyttöohje

Radio

Bruksanvisning

Radio til underbygning

Betjeningsvejledning

Ραδιόφωνο κουζίνας

 Οδηγίαχρήσης

Unterbau-Radio

Bedienungsanleitung

Undercupboard Radio

KH 2299

- 1 -

INDEX PAGE

Intended Use 2

Items supplied 2

Technical data 2

Safety instructions 3

The appliance components 6

Setting up the appliance 6

Fixing the kitchen radio

beneath a wall cabinet 7

Setting up the kitchen radio 7

The Settings menu 8

Further setting possibilities 10

Radio operation 12

Cleaning 16

Disposal 16

CE Conformity 17

Importer 17

Warranty and Service 17

Read the operating instructions carefully before using the

appliance for the rst time and preserve this booklet for later

reference. Pass this booklet on to whoever might acquire the

appliance at a future date.

- 2 -

Intended Use

This Kitchen Radio is intended for use either free-standing or

for assembly beneath a wall cabinet. The intended uses for

this Kitchen Radio are the reception of FM radio transmissions

and as an alarm/timer, using either signal tones or the radio

itself.

This Kitchen Radio is not intended for utilisation in commercial

or industrial applications. The warranty does not provide

compensation for damage caused by improper use of the

appliance!

Items supplied

1 Kitchen radio KH 2299

1 Mounting plate

4 Screws

1 Operating manual

Technical data

Power supply: 220 - 240 V

~

, 50 Hz

Power consumption:

Operation: 5 W

Standby: approx. 1.8 W

Output level: 1 W at 10% THD

Frequency range UKW (FM) 87.5 – 108 MHz

MW (AM) 526,5 – 1606,5 kHz

Operating temperature: +5

~

+35°C

Humidity: 5

~

90 %

(No condensation)

Dimensions

(W x H x D): 27,5 x 15,7 x 6,4 cm

Weight: 1.070 g

Protection class: II /

Backup batteries 2 x 1.5 V Type AAA/Micro

(not supplied)

The technical features of this appliance enable an adjustable

reception capability that exceeds the permitted frequency

range of 87,5–108 MHz and 526,5–1606,5 kHz. In

some countries, dierent national regulations may apply to the

assigned radio frequency ranges. Please note that informa-

tion received outside of the assigned radio frequency ranges

may not be utilised, passed on to third parties or otherwise

misused.

- 3 -

Safety instructions

This appliance is not intended for use by individuals •

(including children) with restricted physical, physiological

or intellectual abilities or deciencies in experience

and/or knowledge unless they are supervised by a person

responsible for their safety or receive from this person

instruction in how the appliance is to be used. Children

should be supervised to ensure that they do not play

with the appliance.

Always remove the power plug before cleaning the •

appliance.

Check the appliance and all parts for visible damages. •

The safety concept can work only if the appliance is in a

faultless condition.

The power plug must always be easily accessible, so •

that in the event of an emergency the appliance can

be quickly disconnected from the mains power supply.

Risk of electrical shocks.

Connect the appliance only to correctly installed and •

earthed mains power sockets. Ensure that the rating of

the local power supply tallies completely with the details

given on the rating plate of the appliance.

Arrange for Customer Services to repair or replace •

connecting cables and/or appliances that are not

functioning properly or have been damaged.

NEVER submerse the appliance in water. Wipe it only •

with a slightly damp cloth.

Do not expose the appliance to rain and never use it in •

a humid or wet environment.

Always take hold of the power cable by the plug. •

Do not pull on the cable itself and never touch the power

cable with wet hands, this could result in either a short

circuit or you receiving an electric shock.

Do not place the appliance, furniture or anything else •

on the power cable and ensure that it does not become

clamped.

NEVER make a knot in the power cable and do NOT •

bind it together with other cables. The power cable

should be positioned so that no one can step on or trip

over it.

Ensure that the power cable does not become wet dur-•

ing operation.

- 4 -

You are not permitted to open the appliance housing or •

repair the appliance. If the housing is opened, you run

the risk of receiving a potentially fatal electric shock and

the warranty lapses.

Protect the appliance against drip and spray water. •

Do not place any water-lled vessels (e.g. ower vases)

on or near the appliance.

 Riskofre!

Do not use the appliance near hot surfaces.•

Do not place the appliance in locations that are subject •

to direct sunlight. Otherwise, it may overheat and become

irreparably damaged.

Do not locate the kitchen radio directly above hotplates. •

The kitchen radio may be damaged. There is a danger

of re!

Never leave the appliance unattended while it is being •

used.

Never cover the ventilation slots of the appliance while •

it is on.

Do not place open re sources, such as candles, on or •

near the appliance.

 Riskofpersonalinjury!

Keep the power cable and appliance away from children. •

Children frequently underestimate the dangers of electrical

appliances.

Provide a stable location for the appliance.•

Do not operate the appliance if it has sustained a fall or •

is damaged.

Arrange for the appliance to be checked and/or repaired •

by qualied technicians.

Keep batteries well away from children. Children can •

put batteries into their mouths and swallow them.

If a battery is swallowed medical assistance must be •

sought immediately.

Note:

Some aggressive furniture nishes can have a destructive •

inuence on the appliance's rubber pads. If necessary,

place the appliance on a nonslip pad.

 Thunderstorms!

Equipment connected to a power supply can be damaged •

during a thunderstorm. You should therefore always

remove the plug from the power socket when there is

a storm.

- 5 -

Notice regarding separation from mains-power

The ON/AOT/OFF switch does not completely discon-

nect the appliance from the power network. Addition-

ally, the appliance consumes power when in standby-

mode.

To completely separate the appliance from mains power,

the power plug MUST be removed from the mains power

socket.

Notice regarding electrical power surges (EFT /

electrical fast transient) and electrostatic

discharges:

In a case of malfunction due to an electrical fast transient

(power surge) and/or electrostatic discharge, the appliance

must be returned to default settings in order to re-establish

normal operation. Possibly the power supply must be

separated and then reconnected. The batteries (if present)

must be removed and then reinserted.

Information regarding the handling of batteries

The appliance uses batteries for memory conservation.

For the handling of batteries please observe the following:

Riskofexplosion!

Do not throw batteries into a re. Do not recharge the •

batteries.

Never open batteries, never solder or weld batteries. •

The risk of explosions and injuries exists!

Regularly check the condition of the batteries. Leaking •

batteries can cause damage to the appliance.

If you do not intend to use the appliance for an extended •

period, remove the batteries.

Should the batteries leak, put on a pair of protective •

gloves and clean the battery compartment and terminals

with a dry cloth.

 Important!

No liability/warranty will be considered for damage

to the Kitchen Radio caused by the eects of moisture,

water penetration or overheating!

- 6 -

The appliance components

q Mounting plate/Baseplate

w Power cable

e Wire aerial

t–i M1–M4 - Memory buttons M1–M4

o MEM/AMS - to save and automatically search

for and save radio stations

a MEM.SCAN - automatic recall of saved radio

stations

s TIMER - controls the timer programming

d Illuminated clamp strip

f AL2/VOL — - controls the alarm function 2

- Volume reduction

g AL1/VOL + - controls the alarm function 1

- Volume increase

h USER/BAND - User switching,

Radio waveband switching

j LIGHT/DIMMER - controls the display and

clamp strip illumination

k MODE/LOCK - recalls the settings,

Button lock

l DOWN - Selection button down

1( UP - Selection button up

2) Battery compartment

2! ON/AOT/OFF - Switch the radio on/o

controls the switch o timer

Setting up the appliance

First take all appliance components from the packaging and

remove all packing foil and tape.

Inserting the back-up batteries

The back-up batteries ensure that the time, date and alarm

time setting are not lost in the event of a power cut. For this

you require two 1.5 V batteries of the type AAA/Micro.

They are not supplied.

1. Open the lid of the battery compartment 2) on the under-

side of the kitchen radio.

2. Insert the batteries. Make sure the polarities are correct.

Otherwise, the memory receipt will not function and dam-

age may be caused to the appliance.

3. Close the lid of the battery compartment 2). The lid must

audibly engage.

- 7 -

Note:

The back-up batteries must be checked at least once

per year and, if necessary, exchanged for new ones.

Fixing the kitchen radio beneath a wall cabinet

With the supplied mounting plate q you can x the kitchen

radio below, for example, a kitchen wall cabinet:

1. Determine a suitable location for the kitchen radio.

2. Press the two retaining levers on the back of the appliance

down. Push the mounting plate q back and remove it.

3. Hold the mounting plate q under the installation location.

Thereby, the front edge of the mounting plate q should

be approx. 3.5 cm behind the front of the kitchen cabinet..

4. Mark the four points for the drillholes with a pencil.

5. Using a spike, make a small depression at the marking

points. Firmly secure the mounting plate q with the sup-

plied screws.

6. Hold the kitchen radio slanted, with the two recesses in

the retaining lugs on the mounting plate q.

Press the kitchen radio upwards until it audibly engages.

Disassembly

To disassemble the kitchen radio, press the two retaining •

levers at the rear of the appliance downwards. Then pull

the radio out to the front and remove it.

Unscrew the screws and remove the assembly plate • q.

Setting up the kitchen radio

Do not set the kitchen radio up without the mounting plate

q. Otherwise the speakers are covered and the sound is

scarcely audible.

To t the kitchen radio with the supplied mounting plate q:

1. Simultaneously press the two retaining levers on the back

of the appliance down.

Push the mounting plate q back and remove it.

2. Push the two retainer lugs on the mounting plate q into

the recesses on the lower rear side of the kitchen radio.

3. Press the mounting plate q rmly in the direction of the

appliance rear until it audibly engages.

- 8 -

Providing mains power

When you have completed installation of the appliance, •

insert the plug into a mains power socket. The display r

is illuminated and the appliance tries to receive an RDS

signal to automatically adjust the time and date.

For as long as the appliance waits for the RDS signal, •

the display r shows "Please wait for setting thanks".

This can take several minutes.

The Settings menu

Setting the time

Should this not succeed, you must set the clock manually. For

this, the radio cannot be switched on (= automatic mode).

1. In automatic mode press the button MODE/LOCK k

once. The time display blinks.

2.Press the buttons UP/DOWN 1(/l to set the time in

minute intervals. Pressing and holding the button changes

the time at ten-minute intervals.

3. Press the button MODE/LOCK k once again to save the

time and switch to the date setting.

If you do not press a button for 10 seconds when making the

settings, the appliance saves the current setting and returns to

automatic mode.

Setting the date

1. In automatic mode press the button MODE/LOCK k

twice. In the display r appears "01.01.2010", the date dis-

play ashes.

2. Press the buttons UP/DOWN 1(/l to set the date

at day intervals. Pressing and holding the buttons chang-

es the date at intervals of 10 days.

3. Press the button MODE/LOCK k once again to save the

date and to switch to setting the memory function.

If you later press the DOWN button l in automatic mode,

the display r briey shows "DAY". Subsequently, the time

and date display alternate themselves. To switch back to an

exclusive time display, press the button DOWN l once

again.

Setting the memory functions

You can programme in up to 6 dates, which the appliance

will remind you of when they are reached.

1. In automatic mode press the button MODE/LOCK k

three times. The display r shows alternatively a date and

the SDA 1 indicator for reminder date 1.

- 9 -

2.Press the buttons UP/DOWN 1(/l to set the rst

desired reminder date. Pressing and holding the buttons

changes the date at intervals of 10 days.

3. When you press the button TIMER s, the year number is

deactivated and thus you are reminded on this date every

year.

4. Should you wish to programme in further dates, press the

button MEM.SCAN a to select the desired memory posi-

tions 2-6.

5. Follow the same steps with the other dates.

6. To deactivate the memory function, programme in a date

that lies in the past.

7. Press the button MODE/LOCK k once again to save the

settings of the memory function and to switch to setting

the update function.

Setting the update function

Using this function, the appliance can automatically update

the settings for the clock based on the RDS data.

1. In automatic mode press the button MODE/LOCK k four

times. The display r shows "UP DATE".

2.Press the button DOWN l, to deactivate the Actual-

isation function. The blinking clock symbol in the dis-

play r then disappears.

3.Press the button UP 1( to reactivate the update function.

The hour symbol appears.

4. Press the button MODE/LOCK k once again to save the

settings of the update function and to switch to setting the

12 or 24 hour mode.

Selecting 12 or 24 hour time display

1. In automatic mode press the button MODE/LOCK k

ve times. In the display r appears "24 HOUR" for the 24

hour modus.

2. Press the button DOWN l to select the 12 hour

modus. In the display r appears "12 HOUR". Press the but-

ton UP 1( to return to the 24 hour modus.

In the 12 hour mode "AM" appears between 0:00 and

11:59 (ante meridiem = mornings) behind the time display,

from 12:00 to 23:59 "PM" (post meridiem = afternoons) is

shown in the display r.

Press the button MODE/LOCK k to save the menu settings

and to close it down.

- 10 -

Further setting possibilities

Setting the display brightness

Press the button LIGHT/DIMMER j repeatedly to set the

brightness level at which the display should be illuminated.

The brightness can be set at 3 levels.

Illuminated clamp strip

Documents, for example recipes, with a width of up to 10 cm

can be inserted and automatically held in the clamp strip d.

If you press and hold the button LIGHT/DIMMER j for two

seconds, the downward facing lamp is switched on, which

then illuminates the recipe. Press and hold the button j once

again for two seconds to switch the lamp o.

Kitchen timer

1. Press the button TIMER s.

2. Using the buttons UP/DOWN 1(/l, set the desired

time interval (a time span between 1 minute and 23:59

h is possible). Pressing and holding one of the buttons

changes the display in ten-minute intervals. Or press one

of the buttons M1–M4 t–i to recall a saved preset

time for the kitchen timer. The following times are factory

pre-programmed:

Button M1 t = 5 min. (Indicator = T1)

Button M2 y = 10 min. (Indicator = T2)

Button M3 u = 15 min. (Indicator = T3)

Button M4 i = 20 min. (Indicator = T4)

3. Press the button TIMER s once again to start the kitchen

timer. In the display r a clock icon running in reverse

and a cooking pot symbol appears.

4. From 30 seconds before expiry of the time span an acoustic

signal sounds, repeating at shorter intervals the closer the

set time approaches. When the time has expired, the alarm

sounds continuously and with increasing volume.

5. Press the button TIMER s to terminate the acoustic signal.

Interrupting the kitchen timer.

To interrupt the kitchen timer, switch to the kitchen timer •

mode by pressing the button TIMER s.

Then briey press the button TIMER • s to interrupt the

kitchen timer.

The time is halted, the indicator blinks for 10 seconds. After

this period the appliance returns to automatic modus. To

restart the kitchen timer, briey press the button TIMER s

again to switch back into the kitchen timer mode.

- 11 -

Press the button TIMER • s once again. The time then con-

tinues to run.

To completely switch the kitchen timer o, press and hold •

the button TIMER s for 3 seconds The clock and cooking

pot symbol disappear.

Programming the kitchen timer

You can programme frequently used times for the kitchen

timer into the appliance, so that you do not need to enter

them in repeatedly. As the appliance can be used by several

people, it has user switching, A/B. Both users can save 4 dif-

ferent timer periods each.

1. First, select the desired user. To switch between users, press

and hold the button USER/BAND h for two seconds.

2. Then press the button TIMER s.

3.Using the buttons UP/DOWN 1(/l enter in the

desired time.

4. Press the button MEM/AMS o. On the right and next to

the time indicator, "T" lights up.

5. Press one of the pre-set buttons M1–M4 t–i, under

which the kitchen timer period should be saved. Its

number is now shown to the right of the "T".

6. Press the button MEM/AMS o once again to conclude

the saving.

Setting alarm times (Alarms 1 and 2)

You can programme two alarm times into your kitchen radio.

Alarm function

Symbol in the display r

Acoustic signal

Radio

Switched o no symbol

1. In automatic mode press the button AL1/VOL. + g (or

AL2/VOL. – f). In the display r the last set alarm time

and the symbol for the type of alarm blink for 10 seconds.

2. Press the buttons UP/DOWN 1(/l to set the desired

alarm time.

3. Press the button AL1/VOL. + g (or AL2/VOL. – f) re-

peatedly until the desired alarm function (see the table

above) is indicated in the display r.

4. Repeatedly press the button TIMER s to set the weekdays

on which you require the alarm function: You can select

- 12 -

between "workdays" (Mo, Tu, We, Th, Fr), "weekends"

(Su, Sa) and "every day" (Su, Mo, Tu, We, Th, Fr, Sa).

Thereby, orientate yourself on the weekday indicator in

the display r:

Mo = Monday

Tu = Tuesday

We = Wednesday

Th = Thursday

Fr = Friday

Sa = Saturday

Su = Sunday.

5. If you hold the button TIMER s pressed down for 2 sec-

onds, you can also, through repeated brief pressing of

the TIMER s button, select a specic weekday (e.g. only

"We"). The selected setting is indicated in the display r.

6. To return to the selection of workdays, weekends or

whole weeks, once again hold the button TIMER s

pressed down for 2 seconds.

7. After 10 seconds the blinking in the display stops and

your input is saved. The appliance then returns to auto-

matic modus.

When the alarm signal sounds...

and the alarm function "Radio" has been selected, the •

radio plays for one hour at a pre-dened alarm volume.

To halt it, press the button AL1/VOL. + g (or AL2/VOL. –

f).

and the alarm function "Signaltones" has been selected, •

the signal tone sounds for 10 minutes, with an increasing

volume. To halt it, press the button AL1/VOL. + g (or AL2/

VOL. – f).

The Reminder function

The appliance can remind you of a date that you have

set with the reminder function. In these cases, from 8:00 –

23:00 on that day, and at every full hour, the acoustic alarm

sounds for 10 minutes. In addition, the SDA-panel in the dis-

play r blinks. To stop the reminder alarm, press any button.

Radio operation

For radio reception, completely unwind the wire aerial e

and, with the radio switched on, determine the most favour-

able positioning for it. The appliance has a built-in ferrite

aerial for the reception of MW transmitters. Should the MW

reception be insucient, please turn the appliance towards a

more favourable direction.

- 13 -

Switching the radio on and off

1. To switch the radio function on, press the button ON/

AOT/OFF 2!. In the display r the currently selected

frequency is shown.

2. Press the button ON/AOT/OFF 2! once again to switch

the radio o and return the appliance to the automatic

modus.

Note:

By pressing and holding the button ON/AOT/OFF

2! you switch to the function switch-o time (see S. 15

chapter AOT Switch-o timer).

Manual station selection

1. Using the button USER/BAND h, select the required

radio frequency: MW (AM) or VHF (FM).

2.Briey press the button UP 1( repeatedly to search for

stations with a higher frequency than the one shown in

the display r.

3. Briey press the button DOWN l repeatedly to search

for stations with a lower frequency than the one shown in

the display r.

4. Should the currently selected radio station transmit RDS

data, the -indicator lights-up in the display r.

Then the display r shows the name of the radio station,

and the time is updated (if activated in the settings, see

section "Setting Update function").

Automatic station search

You can have the kitchen radio search for stations.

The kitchen radio searches the frequency range until it nds

a station.

1. Press and hold the button UP 1( for two seconds: the

kitchen radio searches for the station with the next highest

frequency.

2. Press and hold the button DOWN l for two seconds:

the kitchen radio searches for the station with the next

lowest frequency.

Repeat these steps until you have found a radio station to

your liking.

Save and recall a radio station manually

As the appliance can be used by numerous people, it is tted

with user switching, A/B. Both users can save dierent radio

stations. To switch between users, press and hold the button

USER/BAND h for two seconds.

- 14 -

Each user can save 36 radio stations in the appliance.

32 x VHF stations and 4 x MW stations. For saving UKW

stations, User "A" has available:

Preset button M1 t for the save positions A1 – A8,

Preset button M2 y for the save positions B1 – B8,

Preset button M3 u for the save positions C1 – C8, and

Preset button M4 i for the save positions D1 – D8.

Available for User "B" are:

Preset button M1 t for the save positions 11 – 18,

Preset button M2 y for the save positions 21 – 28,

Preset button M3 u for the save positions 31 – 38, and

Preset button M4 i for the save positions 41 – 48.

Press the corresponding preset button once to address the

save position "1", press twice for "2", etc.

With MW radio stations, each preset button is for one of the

4 save positions.

1. Setting the user, the desired radio wavelength and the

desired radio station.

2. Press the button MEM/AMS o. In the display r the save

position indicator and "MEM" blink.

3. Press one of preset buttons M1–M4 t–i, if necessary

repeatedly, to save the radio station to the desired save

position. In the display r, the indicator for the save posi-

tion selected by you and "MEM" blink.

4. Press the button MEM/AMS o once again. "MEM" and

the save position are constantly indicated, the radio

station is saved.

5. Repeat the steps 1 to 4 (for both users) until all of the de-

sired radio stations are saved.

6. To recall the saved radio stations, press the correspond-

ing preset buttons (M1–M4 t–i) in radio mode, sever-

al times if need be, until the number of the saved position

appears in the display r.

Automatically save and recall a radio station

With the AMS function (Automatic Memory System), the

radio automatically searches for radio stations and then

saves them to the available save positions in the radio wave-

band. Previously saved radio stations are thereby erased.

1. Press and hold the button MEM/AMS o for two sec-

onds. The kitchen radio automatically searches for suf-

ciently powerful radio stations and saves them in the

memory.

2. The station search can be stopped by pressing on the button

MEM/AMS o. The most recently found radio station plays.

- 15 -

3. When you press the button MEM.SCAN a, the saved

radio stations are recalled in their sequence and each is

played for 10 seconds.

4. To quickly move on to another radio station, press the but-

ton MEM.SCAN a.

5. To quit the automatic recall, press the button MODE/

LOCK k. The display r will then show the time for 10

seconds.

Adjusting the volume.

To reduce the sound volume, in radio operation repeat-•

edly press the button AL2/VOL — f, or hold the button

down.

To increase the sound volume, in radio operation repeat-•

edly press the button AL1/VOL. + g, or hold the button

down.

Lock function

You can lock the kitchen radio so that settings cannot be al-

tered by unauthorised people or children.

Press and hold the button MODE/LOCK • k for 3 seconds. A

key symbol appears in the display r.

When a key is pressed and the lock is activated, the key •

symbol blinks but no other functions are carried out.

To disable the lock function, press and hold the button •

MODE/LOCK k until the key symbol extinguishes.

A.O.T. - Switch-off timer

This appliance is tted with a switch-o timer for up to 90

minutes.

1. With the radio switched on, press the button ON/AOT/

OFF 2! down for 2 seconds to recall the function.

2. Repeatedly press the button ON/AOT/OFF 2! to pro-

gramme in the number of minutes, in increments of 5

minutes, for which the appliance is to remain switched on.

After a few seconds the display again shows the radio

station currently being played.

3. On expiry of the time period the appliance switches itself

o.

4. To simply switch the radio function o, press the button

ON/AOT/OFF 2!.

- 16 -

Cleaning

 Warning!

Always remove the plug before cleaning the appliance!

Moisture penetrating into the appliance creates the risk

of electric shock! Additionally, the kitchen radio could

become irreparably damaged!

Clean the housing of the kitchen radio with a slightly moist

cloth and a mild detergent only. Ensure that moisture cannot

permeate into the appliance during cleaning!

Disposal

Do not dispose of the appliance in your normal

domestic waste. This product is subject to the

provisions of European Directive 2002/96/EC.

Disposing of the appliance

Arrange for the product, or parts of it, to be disposed of •

by a professional disposal company or by your communal

waste facility.

Observe the currently applicable regulations. In case of •

doubt, please contact your waste disposal centre.

Disposal of batteries/accumulators

Used batteries/rechargeable batteries may not be •

disposed of in household waste.

Batteries/rechargeable batteries can contain toxic •

substances which may damage the environment. There-

fore, dispose of the batteries/rechargeable batteries in

accordance with statutory regulations.

Every consumer is statutorily obliged to dispose of bat-•

teries/rechargeable batteries to a community collection

centre in their district or to a dealer. The purpose of this

obligation is to ensure that batteries are disposed of in a

non-polluting manner.

Only dispose of batteries when they are fully discharged.•

Disposal of packaging

Dispose of all packaging materials in an environmentally

friendly manner.

- 17 -

CE Conformity

This device complies, regarding conformity, to the basic

requirements and other relevent provisions of the Low Volt-

age Directive 2004/108/EC, the Directive for Low Voltage

Appliances 2006/95/EC and the Eco Design Directive

2009/125/EC (Ordinance 1275/2008 Appendix II,

Number 1).

Importer

KOMPERNASS GMBH

BURGSTRASSE 21

44867 BOCHUM, GERMANY

www.kompernass.com

Warranty and Service

The warranty for this appliance is for 3 years from the date

of purchase. The appliance has been manufactured with

care and meticulously examined before delivery. Please re-

tain your receipt as proof of purchase. In the event of a war-

ranty claim, please make contact by telephone with our Serv-

ice Department. Only in this way can a post-free despatch

for your goods be assured.

The warranty covers only claims for material and maufactur-

ing defects, but not for transport damage, for wearing parts

or for damage to fragile components, e.g. buttons or batter-

ies. This product is for private use only and is not intended for

commercial use.

The warranty is void in the case of abusive and improper

handling, use of force and internal tampering not carried out

by our authorized service branch. Your statutory rights are

not restricted in any way by this warranty.

The warranty period will not be extended by repairs made

unter warranty. This applies alsoto replaced and repaired

parts. Any damage and defects extant on purchase must be

reported immediately after unpacking the appliance, at the

latest, two days after the purchase date. Repairs made after

the expiration of the warranty period are subject to payment.

DES Ltd

Tel.: 0871 5000 700 (£ 0.10 / minute)

e-mail: [email protected]

Kompernass Service Ireland

Tel: 1850 930 412 (0,082 EUR/Min.)

Standard call rates apply. Mobile operators may vary.

e-mail: [email protected]

- 18 -

Seite wird geladen ...

Silvercrest KH 2299 Bedienungsanleitung

Silvercrest KH 2299 Bedienungsanleitung

in anderen Sprachen

Verwandte Artikel

Andere Dokumente