BLACK+DECKER STC1850E Benutzerhandbuch

www.blackanddecker.eu

1

2 13

5

6

8

7

34

9

11

12

10

STC1820E

STC1840E

STC1850E

2

3

English (original instructions) 7

Deutsch (übersetzt von den originalanweisungen) 16

Français (traduction de la notice d’instructions originale) 27

Italiano (tradotto dalle istruzioni originali) 37

Nederlands (vertaald vanuit de originele instructies) 47

Español (traducido de las instrucciones originales) 57

Português (traduzido das instruções originais) 67

Svenska (översatt från de ursprungliga instruktionerna) 77

Norsk (oversatt fra de originale instruksjonene) 87

Dansk (oversat fra original brugsvejledning) 95

Suomi (käännetty alkuperäisestä käyttöohjeesta) 105

Ελληνικά (μετάφραση από τις πρωτότυπες οδηγίες) 114

2

3

A

B

E

F

C

D

12 13

12

14

12

12a

11

19

16

17

20

15

16

18

2

20

21

4

5

G

22

H

5˚-10˚

J1

J2

7

I J

4

5

24

23

60cm

J3

K

A6505-XJ

O

L M

4

7

1 2

6

7

T

P1

P2

P

Q

26

27

25

P2

R

28

29

S

U

31

30

A6481-XJ

7

ENGLISH

(Original instructions)

6

7

Intended use

Your BLACK+DECKER STC1820E, STC1840E, STC1850E

trimmers have been designed for trimming and nishing lawn

edges and to cut grass in conned spaces. This appliance is

intended for consumer use only.

Safety instructions

Warning! When using mains-powered

appliances, basic safety precautions,

including the following, should always be

followed to reduce the risk of re, electric

shock, personal injury and material

damage.

Warning! When using the machine the

safety rules must be followed. For your

own safety and bystanders please read

these instructions before operating the

machine. Please keep the instructions

safe for later use.

uRead all of this manual carefully before

operating the appliance.

uThe intended use is described in this

manual. The use of any accessory

or attachment or the performance

of any operation with this appliance

other than those recommended in this

instruction manual may present a risk

of personal injury.

uRetain this manual for future

reference.

Using your appliance

Always take care when using the

appliance.

uAlways use safety glasses or goggles.

uNever operate the machine while

people, especially children, or pets are

nearby.

uDo not allow children or animals to

come near the work area or to touch

the appliance.

uClose supervision is necessary when

the appliance is used near children.

uThis appliance is not intended for use

by young or inrm persons without

supervision.

uThis appliance is not to be used as a

toy.

uOnly use the appliance in daylight or

good articial light.

uUse in a dry location only. Do not allow

the appliance to become wet.

uAvoid using the appliance in bad

weather conditions, especially when

there is a risk of lightning.

uDo not immerse the appliance in water.

uDo not open the body casing. There

are not user-serviceable parts inside.

uDo not operate the appliance in

explosive atmospheres, such as in the

presence of ammable liquids, gases

or dust.

uThe appliance is only to be used with

the power supply unit provided with the

appliance.

Safety of others

uThis appliance can be used by

children aged from 8 years and above

and persons with reduced physical,

sensory or mental capabilities or

lack of experience and knowledge

if they have been given supervision

or instruction concerning use of

the appliance in a safe way and

understand the hazards involved.

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made by

children without supervision.

uChildren should be supervised to

ensure that they do not play with the

appliance.

8

ENGLISH

(Original instructions)

Residual risks

Additional residual risks may arise when

using the tool which may not be included

in the enclosed safety warnings.

These risks can arise from misuse,

prolonged use etc.

Even with the application of the

relevant safety regulations and the

implementation of safety devices, certain

residual risks can not be avoided. These

include:

uInjuries caused by touching any

rotating/moving parts.

uInjuries caused when changing any

parts, blades or accessories.

uInjuries caused by prolonged use

of a tool. When using any tool for

prolonged periods ensure you take

regular breaks.

uImpairment of hearing.

uHealth hazards caused by breathing

dust developed when using your

tool (example:- working with wood,

especially oak, beech and MDF.)

After use

uWhen not in use, the appliance should

be stored in a dry, well ventilated place

out of reach of children.

uChildren should not have access to

stored appliances.

uWhen the appliance is stored or

transported in a vehicle it should be

placed in the boot or restrained to

prevent movement following sudden

changes in speed or direction.

Inspection and repairs

uBefore use, check the appliance for

damaged or defective parts Check

for breakage of parts and any other

conditions that may affect its operation.

uDo not use the appliance if any part is

damaged or defective.

uHave any damaged or defective parts

repaired or replaced by an authorised

repair agent.

uNever attempt to remove or replace

any parts other than those specied in

this manual.

Vibration

The declared vibration emission values

stated in the technical data and the

declaration of conformity have been

measured in accordance with a standard

test method provided by EN50636 and

may be used for comparing one tool with

another. The declared vibration emission

value may also be used in a preliminary

assessment of exposure.

Warning! The vibration emission value

during actual use of the power tool can

differ from the declared value depending

on the ways in which the tool is used.

The vibration level may increase above

the level stated.

When assessing vibration exposure to

determine safety measures required by

2002/44/EC to protect persons regularly

using power tools in employment, an

estimation of vibration exposure should

consider, the actual conditions of use and

the way the tool is used, including taking

account of all parts of the operating

cycle such as the times when the tool is

switched off and when it is running idle in

addition to the trigger time.

Additional safety instructions for

grass trimmers

Warning! Cutting elements continue to

rotate after the motor is switched off.

9

ENGLISH

(Original instructions)

uBe familiar with the controls and the

proper use of the appliance.

uAlways remove the battery from the

appliance whenever the appliance

is unattended, before clearing a

blockage, before cleaning and

maintenance, after striking a foreign

object or whenever the appliance

starts vibrating abnormally.

uWear stout shoes or boots to protect

your feet.

uWear long trousers to protect your

legs.

uBefore using the appliance, check that

your cutting path is free from sticks,

stones, wire and any other obstacles.

uOnly use the appliance in the upright

position, with the cutting line near the

ground. Never switch the appliance on

in any other position.

uMove slowly when using the appliance.

Be aware that freshly cut grass is

damp and slippery.

uDo not work on steep slopes. Work

across the face of slopes, not up and

down.

uNever cross gravel paths or roads

while the appliance is running.

uNever touch the cutting line while the

appliance is running.

uDo not put the appliance down until the

cutting line has come to a complete

standstill.

uUse only the appropriate type of

cutting line. Never use metal cutting

line or shing line.

uBe careful not to touch the line

trimming blade.

uKeep hands and feet away from the

cutting line at all times, especially

when switching on the motor.

uBefore using the appliance and after

any impact, check for signs of wear or

damage and repair as necessary.

uNever operate the appliance with

damaged guards or without guards in

place.

uTake care against injury from any

device tted for trimming the lament

line length. After extending new cutter

line always return the machine to

its normal operating position before

switching on.

uAlways ensure that the ventilation slots

are kept clear of debris.

Additional safety instructions for

batteries and chargers

Batteries

uNever attempt to open for any reason.

uDo not expose the battery to water.

uDo not store in locations where the

temperature may exceed 40 °C.

uCharge only at ambient temperatures

between 10 °C and 40 °C.

uCharge only using the charger

provided with the tool.

uWhen disposing of batteries, follow

the instructions given in the section

"Protecting the environment".

Chargers

uUse your BLACK+DECKER charger

only to charge the battery in the tool

with which it was supplied. Other

batteries could burst, causing personal

injury and damage.

uNever attempt to charge non-

rechargeable batteries.

uHave defective cords replaced

immediately.

uDo not expose the charger to water.

10

ENGLISH

(Original instructions)

uDo not open the charger.

uDo not probe the charger.

$

The charger is intended for

indoor use only.

Read the instruction manual

before use.

Electrical safety

#

Your charger is double insulated;

therefore no earth wire is

required. Always check that the

mains voltage corresponds to the

voltage on the rating plate. Never

attempt to replace the charger

unit with a regular mains plug.

u If the supply cord is damaged, it must

be replaced by the manufacturer or an

authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Labels on appliance

The following pictograms are shown on

the tool along with the date code:

Read the manual prior to

operation.

Wear safety glasses or goggles

when operating this appliance.

Wear suitable ear protectors

when operating this appliance.

Always remove the battery from

the appliance before performing

any cleaning or maintenance.

Beware of ying objects. Keep

bystanders away from the

cutting area.

Do not expose the appliance to

rain or high humidity.

96

Directive 2000/14/EC

guaranteed sound power.

Features

This appliance includes some or all of the following features.

1. Trigger

2. Lock off button

3. Handle

4. POWERCOMMAND button

5. Auxiliary handle

6. Height adjust collar

7. Flip to edge collar

8. Trimmer head

9. Edge wheel

10. Guard

11. Spool housing

12. Battery

13. Charger

14. Charge indicator

Charging the battery (Fig. A)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell temperature

warms up or cools down.

u Plug the charger into an appropriate outlet before inserting

the battery pack.

u Insert the battery pack into the charger.

The green LED will ash indicating that the battery is being

charged.

The completion of charge is indicated by the green LED

remaining on continuously. The pack is fully charged and

may be used at this time or left in the charger.

Warning! Recharge discharged batteries as soon as possible

after use or battery life may be greatly diminished.

Charger diagnostics

This charger is designed to detect certain problems that can

arise with the battery packs or the power source.

11

ENGLISH

(Original instructions)

Problems are indicated by one LED ashing in different

patterns.

Bad Battery

The charger can detect a weak or damaged battery. The

red LED ashes in the pattern indicated on the label. If you

see this bad battery blink pattern, do not continue to charge

the battery. Return it to a service centre or a collection site

for recycling

Hot/Cold Pack Delay

When the charger detects a battery that is excessively

hot or excessively cold, it automatically starts a Hot/Cold

Pack delay, suspending charging until the battery has

normalised. After this happens, the charger automatically

switches to the Pack Charging mode. This feature ensures

maximum battery life. The red LED ashes in the pattern

indicated on the label when the Hot/Cold pack delay is

detected.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18°- 24°C). DO NOT charge the

battery pack in an air temperature below +40°F (+4.5°C),

or above +105°F (+40.5°C). This is important and will

prevent serious damage to the battery pack .

u The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack

in a warm environment such as in a metal shed, or an

uninsulated trailer

u If the battery pack does not charge properly:

u Check current at receptacle by plugging in a lamp or

other appliance

u Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F

- 75°F (18°- 24°C).

u If charging problems persist, take the appliance, battery

pack and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, steel wool, aluminium foil, or any buildup

of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger

before attempting to clean.

u Do not freeze or immerse charger in water or any other

liquid.

Warning! Shock hazard. Do not allow any liquid to get inside

charger. Never attempt to open the battery pack for any

reason.

If the plastic housing of the battery pack breaks or cracks,

return to a service center for recycling.

Installing and removing the battery pack from the

appliance

Warning! Make certain the lock-off button is not engaged to

prevent switch actuation before removing or installing battery.

To install battery pack

Insert battery (12) into appliance until an audible click is

heard (Figure B). Ensure battery pack is fully seated and fully

latched into position.

To remove battery pack

Depress the battery release button (12a) as shown in Figure C

and pull battery pack out of appliance.

Assembly

Warning! Before assembly, make sure that the tool is

switched off and the battery has been removed.

Assembly tools required (not supplied):

Phillips Screwdriver.

Fitting the guard (Fig. D, E)

Warning! Remove the battery from the appliance before

attempting to attach the guard, edge guide or handle. Never

operate appliance without guard rmly in place.

The guard must always be on the appliance to protect the

user.

u Remove the screw from the guard.

u Turn the trimmer upside down so that you are looking

down at the spool cap (15).

u Turn the guard (10) upside down and slide it fully onto the

motor housing (16). Make sure the tabs (17) on the guard

engage the ribs (18) on the motor housing as shown.

u Continue to slide the guard on until you hear it “snap” into

place. The locking tab (19) should snap into the housing

slot (20).

12

ENGLISH

(Original instructions)

u Using a phillips screwdriver, insert the guard screw and

tighten securely as shown in Figure E to complete the

guard assembly.

u Once the guard is installed, remove the covering from the

line cut-off blade, located on the edge of the guard

Warning! Never use the tool unless the guard is properly

tted.

Attaching the auxiliary handle (Fig. F, G, H)

u To attach the handle, press in on the buttons (21) on both

sides of the upper housing as shown in Figure F.

u Position the handle as shown in Figure G (with the

BLACK+DECKER logo facing upward). Partially push the

handle on so it will hold the buttons in when you release

them with your hand.

u Push the handle completely onto the housing and position

it slightly until it “snaps” into place.

u To adjust the handle up or down, press in on the button

(22) and raise or lower the handle (Figure H).

u The handle should be adjusted so that your front arm is

straight when the trimmer is in the working position.

Height adjustment (Fig. I, J–J3)

Warning! Adjust the length of the trimmer to obtain proper

working positions shown in Figures J - J3.

u The overall height of the trimmer can be adjusted by

loosening the height-adjust collar (6) by rotating it in the

direction of the arrow shown in Figure I.

u Move the upper housing straight up or down. When the

desired height is achieved, tighten the collar by rotating it

opposite of the direction shown in Figure I.

Releasing the cutting line

In transit, the cutting line is taped to the spool housing.

u Remove the tape holding the cutting line to the spool

housing.

Operation

Warning! Always use proper eye protection.

Warning! Before you begin trimming, only use the appropriate

type of cutting line.

Note: Inspect area to be trimmed and remove any wire, cord,

or string-like objects which could become entangled in the

rotating line or spool. Be particularly careful to avoid any wire

which might be bent outwardly into the path of the appliance,

such as barbs at the base of a chain link fence.

Switching on and off

u To switch the appliance on, push the lock-off button (2),

and squeeze the trigger (1).

u To switch the appliance off, release the trigger.

Operating the trimmer (Fig. I, J–J3)

u With the unit on, angle unit and slowly swing the trimmer

side to side as shown in Figure J.

u Maintain a cutting angle of 5° to 10° as shown in

Figure J1. Do not exceed 10° (Figure J2). Cut with the tip

of the line. To keep distance from hard surfaces use edge

wheel (9).

u Maintain a minimum distance of 60 cm between the guard

and your feet as shown in Figure J3. To acheive this

distance adjust the overall height of the trimmer as shown

in Figure I.

POWERCOMMAND Button (Fig. K)

The POWERCOMMAND

feature allows you to advance the

length of cutting line available while trimming.

u To extend the cutting line, fully depress the

POWERCOMMAND button (4) while trimming and then

release (gure K).

Note: The trimmer will stop cutting when the

POWERCOMMAND button is pressed and will resume cutting

when released.

u For maximum line length, press the button multiple times

until you hear the cutting line hitting the guard.

Note: Do not continue to press the POWERCOMMAND

button once the maximum length is reached. This will result in

overfeeding and will consume string quickly.

Convert to edging mode (Fig. L, M)

Warning! The wheeled edge guide should only be used when

in the edging mode.

The trimmer can be used in trimming mode or edging mode to

trim overhanging grass along lawn edges and ower beds. For

edging, the trimmer head should be in the position shown in

Figure M. If it is not:

u Remove the battery from the trimmer.

u Grasp the ip-to-edge collar (7) and push down as

shown in part 1 of Figure L.

u Rotate the ip-to-edge collar 180° counterclockwise as

shown in part 2, until the handle snaps back into the

upper half of the trimmer.

u To return to trimming position, pull the ip-to-edge collar

down and rotate the head clockwise back to its original

position.

Note: You will experience faster than normal cutting line wear

if the trimmer line is positioned directly over the sidewalk or

abrasive surface.

Edging (Fig. M)

Warning! When being used as an Edger, stones, pieces of

metal and other objects can be thrown out at high speed by

the line. The trimmer and guard are designed to reduce the

danger. However, MAKE SURE that other persons and pets

are at least 30 m away. Optimum cutting results are achieved

on edges deeper than 50 mm.

u Do not use this trimmer to create trenches.

u Using the edging wheel (9), guide the trimmer as shown in

Figure M.

13

ENGLISH

(Original instructions)

u Position the edging wheel on the edge of the sidewalk or

abrasive surface so the cutting line is over the grass or dirt

area to be edged.

u To make a closer cut, slightly tilt the trimmer.

Speed control & runtime extension mode (Fig. N)

This string trimmer gives you the choice to operate at a

more efcient speed to extend the runtime for larger jobs, or

accelerate the trimmer speed for high-performance cutting

(Figure N).

u To extend runtime, pull the speed-control switch back

toward the battery (12) into position #1. This mode is best

for larger projects that require more time to complete.

u To accelerate the trimmer, push the speed-control switch

forward toward the trimmer head (8) into position #2.

This mode is best to cut through heavier growth and for

applications that need higher RPM.

Note: When in acceleration mode (#2), runtime will be

decreased as compared to when trimmer is in extended

runtime mode (#1).

Helpful cutting tips

u Use the tip of the string to do the cutting; do not force

string head into uncut grass. Use edge guide along

such things as fences, houses and ower beds for best

practices.

u Wire and picket fences cause extra string wear, even

breakage. Stone and brick walls, curbs, and wood may

wear string rapidly.

u Do not allow spool cap to drag on ground or other

surfaces.

u In long growth cut from the top down and do not exceed

300 mm high.

u Keep trimmer tilted toward the area being cut; this is the

best cutting area.

u The trimmer cuts when passing the unit from the right to

left. This will avoid throwing debris at the operator.

u Avoid trees and shrubs. Tree bark, wood moldings, siding,

and fence posts can easily be damaged by the string.

Cutting line / line feeding

Your trimmer uses 1.65 mm diameter, Round nylon line.

During use, the tips of the nylon lines will become frayed and

worn and the special self feeding spool will automatically feed

and trim a fresh length of line. Cutting line will wear faster and

require more feeding if the cutting or edging is done along

sidewalks or other abrasive surfaces or heavier weeds are

being cut. The advanced automatic line feeding mechanism

senses when more cutting line is needed and feeds and

trims the correct length of line whenever it’s required. Do not

bump unit on ground in attempt to feed line or for any other

purposes.

Clearing jams and tangled line (Figures O, P, Q)

Warning! Remove the battery from the trimmer before

making any assembly, adjustments or changing accessories.

Such preventive safety measures reduce the risk of starting

the appliance accidentally. From time to time, especially

when cutting thick or stalky weeds, the line feeding hub may

become clogged with sap or other material and the line will

become jammed as a result. To clear the jam, follow the steps

listed below.

u Remove the battery from the trimmer.

u Press the release tabs (23) on the line spool cap (24),

as shown in Figure O and remove the cap by pulling it

straight off.

u Pull the nylon line spool out and clear any broken line or

cutting debris from the spool area.

u Place spool and line into spool cap with line “parked” in

slots provided as shown in Figure P1.

u Insert the line end through the appropriate hole in the

spool housing. Pull slack line through until it pulls out of

the holding slots as shown in Figure P2.

u Press the spool down gently and rotate it until you feel it

drop into place and then push to snap into place. (When

in place, the spool will turn a few degrees left and right

freely).

u Take care to keep the line from becoming trapped under

the spool.

u Align the spool cap tabs with the slots on the spool

housing.

u Snap the spool cap back on as shown in Figure Q by

depressing lugs and pressing into spool housing.

Note: Make sure that cover is fully positioned, listen for two

audible clicks to ensure both lugs are correctly located. Power

the appliance on. In a few seconds or less you’ll hear the

nylon line being cut automatically to the proper length.

Warning! To avoid appliance damage, if the cutting line

protrudes beyond the trimming blade, cut it off so that it just

reaches the blade.

Note: Other replacement parts (guards, spool caps, etc.) are

available through BLACK+DECKER service centers. To nd

your local service location visit www.blackanddecker.com.

Warning! The use of any accessory not recommended by

BLACK+DECKER for use with this appliance could be

hazardous.

Replacing the spool (Fig. O, P, Q, R)

u Remove battery from appliance.

u Depress the tabs (23) and remove the spool cap (24) from

the spool housing (11) (Figure O).

u Grasp empty spool with one hand and spool housing with

other hand and pull spool out.

u If lever (25) or spring (26) in base of housing (Figure R)

becomes dislodged, replace in correct position before

inserting new spool into housing.

14

ENGLISH

(Original instructions)

u Remove any dirt and grass from the spool and housing.

u Unfasten the end of the cutting line and guide the line into

the eyelet (P2) Figure P.

u Take the new spool and push it onto the boss (27)

(Figure R) in the housing. Rotate the spool slightly until it

is seated. The line should protrude approximately 136 mm

from the housing.

u Align the tabs on the spool cap with the slots in the

housing (Figure Q).

u Push the cap onto the housing until it snaps securely into

place.

Rewinding spool from bulk line (Fig. S, T, U)

Bulk line is also available for purchase from your local retailer.

Note: Hand wound spools from bulk line are likely to become

tangled more frequently than BLACK+DECKER factory

wound spools. For best results, factory wound spools are

recommended. To install bulk line, follow the steps below:

u Remove battery from appliance.

u Remove the empty spool from the appliance as described

in “Replacing the spool.”

u Remove any remaining cutting line from the spool.

u Make a fold at the end of the cutting line at about 19 mm

(28). Feed the cutting line into one of the line anchoring

slots (29) as shown in Figure S.

u Insert the 19 mm end of the bulk line into the hole (30) in

the spool adjacent to the slot as shown in Figure T. Make

sure the line is pulled tight against the spool as shown in

Figure T.

u Wind the cutting line onto the spool in the direction of the

arrow on the spool. Make sure to wind the line on neatly

and in layers. Do not crisscross (Figure U).

u When the wound cutting line reaches the recesses (31),

cut the line (Figure T).

u Fit the spool onto the appliance as described in “Replacing

the spool”.

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool/appliance care and regular

cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

uRegularly clean the cutting line and spool using a soft

brush or dry cloth.

u Regularly use a blunt scraper to remove grass and dirt

from the underneath of the guard.

Troubleshooting

Problem Solution

Appliance runs slowly. Remove battery from trimmer.

Check that the spool housing can

rotate freely. Carefully clean it if

necessary.

Check that the cutting line does not

protrude more than approximately

122 mm from the spool. If it does, cut

it off so that it just reaches the line

trimming blade

Automatic line feed does not feed

line.

More line is fed when the line

shortens to approximately 76 mm. To

determine if the line is not feeding, let

line wear past this point.

Keep the tabs depressed and remove

the spoolcap with the spool from the

spool housing in the trimmer head.

Ensure that the line is not

crisscrossed on the spool as detailed

in (Fig. U). If it is unwind the cutting

line and rewind it neatly.

Inspect tracks at the bottom of spool

for damage. If damaged, replace

spool.

Pull the cutting line until it protrudes

approximately 122 mm from the

spool. If insufcient cutting line is left

on the spool, install a new spool of

cutting line.

Align the tabs on the spool cap with

the cut outs in the housing.

Push the spool cap onto the housing

until it snaps securely into place.

If the cutting line protrudes beyond

the trimming blade, cut it off so

that it just reaches the blade. If the

automatic line feed still does not

work or the spool is jammed, try the

following suggestions:

Carefully clean the spool and

housing.

Make sure you are using correct line

size and diameter (2.00 mm) - smaller

and larger line sizes will affect the

functionality of the auto feed system.

Remove the spool and check if

the lever in the spool housing can

move freely.

Remove the spool and unwind the

cutting line, then wind it on neatly

again. Replace the spool into the

housing.

15

ENGLISH

(Original instructions)

Overfeeding Ensure you are cutting with the tip of

the line 177 mm from the spool. Use

the edge guide if needed to ensure

proper space is maintained.

Ensure you are not exceeding a 10º

angle as shown in (Fig. J1). Avoid

contact of the line with hard surfaces

such as brick, concrete, wood etc.

This will prevent excessive wear and/

or overfeed of line. Cut with the tip

of the line

Line unravels when cap or spool is

removed

Make sure to park the lines in holding

slots (Figure P) before removing.

Protecting the environment

Z

Separate collection. Products and batteries

marked with this symbol must not be disposed of

with normal household waste.

Products and batteries contain materials that can be

recovered or recycled reducing the demand for raw materials.

Please recycle electrical products and batteries according

to local provisions. Further information is available at

www.2helpU.com

Technical data

STC1820E STC1840E, STC1850E

Input Voltage

V

DC

18 18

No-Load Speed

min

-1

5500 - 7400 5500 - 7200

Weight

kg 2.1 2.1

Swath Size

cm 28 30

Batteries Charger (minutes)

Cat#

Vdc

Ah

Weight

Kg

Cat# 90590287* N517388* BDC1A BDC2A BDC2A36

Amps 400mA 1A 1A 2A 1.35A

BL1518 18 1.5 0.38 BL1518 225 90 90 25 X

BL1518ST 18 1.5 0.38 BL1518ST 225 90 90 45 X

BL2018 18 2.0 0.39 BL2018 300 120 120 60 X

BL2018ST 18 2.0 0.39 BL2018ST 300 120 120 60 X

BL2518 18 2.5 0.43 BL2518 380 150 150 75 X

BL4018 18 4.0 0.64 BL4018 600 240 240 120 X

BL5018 18 5.0 0.7 BL5018 750 300 300 135 X

BL20362 36 2.0 0.64 BL20362 X X X X 90

BL2536 36 2.5 0.68 BL2536 X X X X 110

BL1554 18/54 1.5 1.08 BL1554 225 90 90 45 X

BL2554 18/54 2.5 1.2 BL2554 380 150 150 75 X

*Not sold as an accessory

Hand/arm weighted vibration value according to

EN50636-2-91:

= < 2,5 m/s

2

, uncertainty (K) = 1,5 m/s

2

.

L

PA

(sound pressure) 79 dB(A)

uncertainty (K) = 3 dB(A)

EC declaration of conformity

MACHINERY DIRECTIVE

OUTDOOR NOISE DIRECTIVE

STC1820E, STC1840E, STC1850E

Cordless String Trimmer

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60335-1:2012 + A11:2014 + A13:2017

EN50636-2-91:2014

2000/14/EC, Lawn Trimmer, L ≤ 50 cm, Annex VI

DEKRA Certication B.V.

Meander 1051 / P.O. Box 5185

6825 MJ ARNHEM / 6802 ED ARNHEM, Netherlands

Notied Body ID No.: 0344

Level of sound power according to 2000/14/EC

(Article 12, Annex III, L ≤ 50 cm):

L

WA

(measured sound power) 93 dB(A)

uncertainty (K) = 3 dB(A)

L

WA

(guaranteed sound power) 96 dB(A)

These products also comply with Directive 2014/30/EU and

2011/65/EU.

For more information, please contact Black & Decker at the

following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker.

Paul Featherstone

Director – Outdoor Products Group

Black & Decker Europe, 270 Bath Road, Slough,

Berkshire, SL1 4DX

United Kingdom

02/07/2020

Guarantee

Black & Decker is condent of the quality of its products

and offers consumers a 24 month guarantee from the date

of purchase. This guarantee is in addition to and in no way

prejudices your statutory rights. The guarantee is valid within

the territories of the Member States of the European Union

and the European Free Trade Area.

(Übersetzung der ursprünglichen

Anweisungen)

DEUTSCH

16

ENGLISH

(Original instructions)

(Übersetzung der ursprünglichen

Anweisungen)

DEUTSCH

Verwendungszweck

Ihr BLACK+DECKER Rasentrimmer STC1820E, STC1840E,

STC1850E wurde für das Trimmen und Zuschneiden von

Rasenkanten sowie für das Schneiden von Gras in beengten

Platzverhältnissen entwickelt. Dieses Gerät ist nicht für den

gewerblichen Einsatz vorgesehen.

Sicherheitshinweise

Warnung! Beachten Sie beim Umgang

mit netzstrombetriebenen Geräten stets

die grundlegenden Sicherheitshinweise,

die im Folgenden beschrieben werden.

Dadurch verhindern Sie Brände,

Stromschläge sowie Sach- und

Personenschäden.

Warnung! Beachten Sie beim

Verwenden des Geräts unbedingt die

Sicherheitsregeln. Lesen Sie zu Ihrer

eigenen Sicherheit und zum Schutz

in der Nähe bendlicher Personen vor

Gebrauch des Geräts die folgende

Bedienungsanleitung. Heben Sie diese

Anleitung zur späteren Verwendung gut

auf.

uLesen Sie diese Anleitung vollständig

und aufmerksam durch, bevor Sie das

Gerät verwenden.

uDer vorgesehene Verwendungszweck

ist in dieser Anleitung beschrieben.

To claim on the guarantee, the claim must be in accordance

with Black&Decker Terms and Conditions and you will need to

submit proof of purchase to the seller or an authorised repair

agent. Terms and conditions of the Black&Decker 2 year

guarantee and the location of your nearest authorised repair

agent can be obtained on the Internet at www.2helpU.com, or

by contacting your local Black & Decker ofce at the address

indicated in this manual.

Please visit our website www.blackanddecker.co.uk to register

your new Black & Decker product and receive updates on new

products and special offers.

Bei Verwendung von Zubehör oder

Anbauteilen, die nicht in dieser

Anleitung empfohlen werden, sowie

bei der Verwendung des Geräts

in Abweichung von den in dieser

Anleitung beschriebenen Verfahren

besteht Verletzungsgefahr.

uBewahren Sie diese Anleitung auf.

Verwendung des Geräts

Verwenden Sie das Gerät stets mit

Umsicht.

uTragen Sie stets eine Schutzbrille.

uEs sollte stets ein Sicherheitsabstand

zu anderen Personen, insbesondere

Kindern, und Haustieren eingehalten

werden.

uAchten Sie darauf, dass sich im

Arbeitsbereich keine Kinder oder Tiere

aufhalten. Verhindern Sie, dass Kinder

das Gerät berühren.

uSeien Sie besonders vorsichtig, wenn

Sie das Gerät in der Nähe von Kindern

verwenden.

uDas Gerät ist nicht für die

unbeaufsichtigte Verwendung durch

Kinder oder gebrechliche Personen

vorgesehen.

uDas Gerät ist kein Spielzeug.

uBetreiben Sie das Gerät nur bei

Tageslicht oder bei ausreichender

Beleuchtung.

uVerwenden Sie das Gerät nur in

trockener Umgebung. Achten Sie

darauf, dass das Gerät nicht nass

wird.

uVermeiden Sie, das Gerät bei

schlechtem Wetter zu verwenden, vor

allem, wenn das Risiko von Blitzen

besteht.

17

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

17

DEUTSCH

uTauchen Sie das Gerät nicht in

Wasser.

uVersuchen Sie nicht, das Gehäuse zu

öffnen. Im Inneren benden sich keine

zu wartenden Teile.

uBetreiben Sie das Gerät nicht in

explosionsgefährdeter Umgebung,

in der sich brennbare Flüssigkeiten,

Gase oder Staub benden.

uDas Gerät darf nur mit dem im

Lieferumfang enthaltenen Netzteil

betrieben werden.

Sicherheit anderer Personen

uDieses Gerät kann von Kindern

ab 8 Jahren und Personen mit

eingeschränkter körperlicher,

sensorischer oder geistiger

Leistungsfähigkeit oder mangelnder

Erfahrung und Kenntnis verwendet

werden, wenn sie eine Aufsicht oder

Anweisung zur sicheren Verwendung

des Geräts erhalten haben und die

Gefahren verstehen beteiligt. Kinder

dürfen nicht mit dem Gerät spielen.

Reinigung und Wartung durch den

Benutzer dürfen nicht von Kindern

ohne Aufsicht durchgeführt werden..

uKinder müssen beaufsichtigt werden,

um sicherzustellen,

dass sie nicht mit dem Gerät spielen.

Restrisiken

Beim Gebrauch dieses Geräts

verbleiben zusätzliche Restrisiken,

die möglicherweise nicht in den

Sicherheitswarnungen genannt werden.

Diese Risiken bestehen beispielsweise

bei Missbrauch oder längerem Gebrauch.

Auch bei der Einhaltung der

entsprechenden Sicherheitsvorschriften

und der Verwendung aller

Sicherheitsgeräte bestehen weiterhin

bestimmte Restrisiken. Diese sind:

uVerletzungen, die durch das Berühren

von sich drehenden/bewegenden

Teilen verursacht werden.

uVerletzungen, die durch das

Austauschen von Teilen, Sägeblättern

oder Zubehör verursacht werden.

uVerletzungen, die durch längeren

Gebrauch eines Geräts verursacht

werden. Legen Sie bei längerem

Gebrauch regelmäßige Pausen ein.

uBeeinträchtigung des Gehörs.

uGesundheitsrisiken durch das

Einatmen von Staub beim Gebrauch

des Geräts (beispielsweise bei

Holzarbeiten, insbesondere Eiche,

Buche und Pressspan).

Nach dem Gebrauch

uBewahren Sie das Gerät bei

Nichtgebrauch an einem trockenen,

gut belüfteten Ort außerhalb der

Reichweite von Kindern auf.

uKinder sollten keinen Zugang zu

aufbewahrten Geräten haben.

uWenn das Gerät in einem Fahrzeug

transportiert oder gelagert wird,

bewahren Sie es im Kofferraum oder

einer geeigneten Ablage auf, damit

es bei plötzlichen Geschwindigkeits-

oder Richtungsänderungen nicht in

Bewegung geraten kann.

Inspektion und Reparaturen

uPrüfen Sie das Gerät vor der

Verwendung auf beschädigte oder

defekte Teile.

18

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

Prüfen Sie, ob Teile beschädigt sind

oder andere Bedingungen vorliegen,

die die Funktion beeinträchtigen

können.

uBetreiben Sie das Gerät nicht, wenn

ein Teil beschädigt oder defekt ist.

uLassen Sie beschädigte oder defekte

Teile in einer Vertragswerkstatt

reparieren oder austauschen.

uErsetzen oder entfernen Sie keine

Teile, für die in dieser Anleitung

keine entsprechende Beschreibung

enthalten ist.

Vibration

Die in den Abschnitten "Technische

Daten" und "EG-Konformitätserklärung"

angegebenen Werte für die

Vibrationsemission wurden mit einer

Standard-Prüfmethode nach EN50636

ermittelt und können zum Vergleich

verschiedener Geräte herangezogen

werden. Außerdem kann mit Hilfe dieses

Werts die Belastung bei Verwendung des

Geräts schon im Voraus eingeschätzt

werden.

Achtung! Die bei Verwendung des

Geräts auftretende Vibrationsemission

hängt von der Art des Gerätegebrauchs

ab und kann dementsprechend von

dem angegebenen Wert abweichen.

Gegebenenfalls kann die Vibration über

dem angegebenen Wert liegen.

Für die Ermittlung der Vibrationsbelas-

tung müssen die tatsächlichen Ein-

satzbedingungen und Verwendungen

des Geräts während des gesamten

Arbeitsgangs berücksichtigt werden,

einschließlich der Zeiten, wenn das Gerät

nicht verwendet oder im Leerlauf betrie-

ben wird.

Diese Werte werden benötigt, um die

gemäß 2002/44/EG erforderlichen

Sicherheitsmaßnahmen zum Schutz von

Personen festlegen zu können.

Zusätzliche Sicherheitshinweise

für Rasentrimmer

Warnung! Die Schneidevorrichtung

rotiert nach Abschalten des Geräts einige

Sekunden lang weiter.

uMachen Sie sich mit den

Bedienelementen und dem

ordnungsgemäßen Gebrauch des

Geräts vertraut.

uEntfernen Sie den Akku aus dem

Gerät, wenn das Gerät unbeaufsichtigt

ist, bevor eine Blockierung, vor

Reinigungs- und Wartungsarbeiten,

nachdem ein Fremdkörper oder wenn

das Gerät startet abnormal vibriert.

uTragen Sie stabile Schuhe oder Stiefel,

um Ihre Füße zu schützen.

uTragen Sie lange Hosen, um Ihre

Beine zu schützen.

uVergewissern Sie sich vor

Verwenden des Geräts, dass die zu

beschneidende Fläche frei von Ästen,

Steinen, Draht und anderen Objekten

ist.

uVerwenden Sie das Gerät

ausschließlich in aufrechter Stellung

und mit Schneidfaden in Bodennähe.

Schalten Sie das Gerät keinesfalls in

einer anderen Stellung ein.

uAchten Sie bei Verwendung des

Geräts auf langsame Bewegungen.

Bedenken Sie, dass frisch gemähtes

Gras feucht und rutschig sein kann.

uArbeiten Sie nie an steilen Hängen.

19

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

Schieben Sie das Gerät immer parallel

zum Hang, nie den Hang hinauf oder

hinunter.

uSchalten Sie das Gerät vor dem

Überqueren von Kieswegen und

Straßen aus.

uBerühren Sie niemals den

Schneidfaden, während sich das Gerät

in Betrieb bendet.

uWarten Sie stets, bis der Schneidfaden

vollständig zum Stillstand gekommen

ist, bevor Sie das Gerät absetzen.

uVerwenden Sie ausschließlich

geeignete Schneidfäden. Verwenden

Sie keinesfalls Schneidfäden aus

Metall oder Angelschnur.

uBerühren Sie auf keinen Fall das

Fadenschneidemesser.

uHalten Sie Hände und Füße stets vom

Schneidfaden fern, insbesondere beim

Einschalten des Geräts.

uÜberprüfen Sie das Gerät vor

Gebrauch und nach Stößen auf

Beschädigungen und Verschleiß,

und veranlassen Sie notwendige

Reparaturmaßnahmen.

uBetreiben Sie keinesfalls das Gerät,

wenn die Schutzvorrichtungen

beschädigt oder nicht ordnungsgemäß

angebracht sind.

uSchützen Sie sich vor Verletzungen

beim Verwenden von Geräten zum

Verkürzen des Schneidfadens.

Bringen Sie nach Herausziehen des

neuen Schneidfadens das Gerät

vor dem Einschalten in die normale

Betriebsposition.

uStellen Sie stets sicher, dass

die Lüftungsschlitze frei von

Verschmutzungen sind.

Zusätzliche Sicherheitshinweise

für Akkus und Ladegeräte

Akkus

uKeinesfalls versuchen, den Akku zu

öffnen.

uAchten Sie darauf, dass der Akku nicht

mit Wasser in Berührung kommt.

uNicht bei Temperaturen über 40 °C

lagern.

uLaden Sie den Akku nur bei

Umgebungstemperaturen von 10 °C

bis 40 °C auf.

uVerwenden Sie ausschließlich das

mitgelieferte Ladegerät.

uBeachten Sie zur Entsorgung von

Akkus oder Batterien die Hinweise im

Abschnitt „Umweltschutz“.

Ladegeräte

uVerwenden Sie das BLACK+DECKER

Ladegerät nur für den Akku des

Werkzeugs, mit dem es geliefert

wurde. Andere Akkus können platzen

und Sachschäden oder Verletzungen

verursachen.

uVersuchen Sie keinesfalls, nicht

auadbare Batterien zu laden.

uLassen Sie beschädigte Kabel sofort

austauschen.

uAchten Sie darauf, dass das Ladegerät

nicht mit Wasser in Berührung kommt.

uVersuchen Sie nicht, das Ladegerät zu

öffnen.

uNehmen Sie am Ladegerät keine

Veränderungen vor.

$

Das Ladegerät darf nur im

Innenbereich verwendet werden.

Vor Gebrauch die Anleitung

lesen.

20

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

Elektrische Sicherheit

#

Das Ladegerät ist schutzisoliert,

daher ist keine Erdleitung

erforderlich. Stellen Sie sicher,

dass die Netzspannung der auf

dem Typenschild des Geräts

angegebenen Spannung

entspricht.

Ersetzen Sie das Ladegerät keinesfalls

durch ein normales Netzkabel.

uBei einer Beschädigung des

Netzkabels muss dieses durch den

Hersteller oder eine BLACK+DECKER

Vertragswerkstatt ausgetauscht

werden, um mögliche Gefahren zu

vermeiden.

Warnsymbole am Gerät

Die folgenden Warnsymbole sind am

Gerät inkl. Datumscode angebracht:

Lesen Sie vor Inbetriebnahme

die Bedienungsanleitung.

Tragen Sie eine Schutzbrille,

wenn Sie mit dem Gerät

arbeiten.

Tragen Sie einen geeigneten

Gehörschutz, wenn Sie mit dem

Gerät arbeiten.

Entfernen Sie den Akku aus dem

Gerät, bevor Reinigungs- oder

Wartungsarbeiten durchgeführt

werden.

Achten Sie auf Gegenstände,

die eventuell umhergeschleudert

werden. Halten Sie andere

Personen von der Schneidzone

fern.

Schützen Sie das Gerät vor

Feuchtigkeit und Regen.

96

Garantierter Schalldruckpegel,

gemessen nach Richtlinie

2000/14/EG.

Merkmale

Dieses Gerät verfügt über einige oder alle der folgenden

Merkmale:

1. Auslöser

2. Einschaltsperre

3. Griff

4. POWERCOMMAND-Taste

5. Zusatzgriff

6. Stellring für die Höhenanpassung

7. Stellring zum Umstellen der Schnittführung

8. Trimmerkopf

9. Kantenrad

10. Schutzhaube

11. Spulengehäuse

12. Akku

13. Ladegerät

14. Ladeanzeige

Laden des Akkus (Abb. A)

Der Akku muss vor der erstmaligen Benutzung sowie immer

dann aufgeladen werden, wenn das Gerät nicht mehr mit

voller Leistung arbeitet.

Der Akku kann sich während des Auadens erwärmen. Das ist

normal und deutet nicht auf ein Problem hin.

Warnung ! Laden Sie den Akku nicht, wenn die

Umgebungstemperatur unter 10 °C oder über 40 °C liegt.

Empfohlene Ladetemperatur: ca. 24 °C.

Hinweis: Ein Akku, bei dem die Temperatur der Akkuzellen

unter ca. 10 °C oder über 40 °C liegt, wird vom Ladegerät

nicht geladen.

Lassen Sie in diesem Fall den Akku im Ladegerät. Das

Ladegerät beginnt automatisch mit dem Ladevorgang, sobald

sich die Zellen erwärmt bzw. abgekühlt haben.

u Stecken Sie das Ladegerät in eine geeignete Steckdose

ein, bevor Sie den Akku einsetzen.

u Setzen Sie den Akku in das Ladegerät ein.

Die grüne LED blinkt, wenn der Akku geladen wird.

Seite laden ...

BLACK+DECKER STC1850E Benutzerhandbuch

BLACK+DECKER STC1850E Benutzerhandbuch

in anderen Sprachen

Verwandte Papiere

Sonstige Unterlagen