Zanussi ZWF14010S Benutzerhandbuch

Kategorie
Waschmaschinen
Typ
Benutzerhandbuch
GETTING
STARTED?
EASY.
User Manual
=:)6
(1 8VHU0DQXDO
:DVKLQJ0DFKLQH
'( %HQXW]HULQIRUPDWLRQ 
:DVFKPDVFKLQH
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an
incorrect installation and use causes injuries and damages.
Always keep the instructions with the appliance for future
reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Do not let children play with the appliance.
Children of less than 3 years should be kept away unless
continuously supervised.
Keep all packaging away from children.
Keep all detergents away from children.
Keep children and pets away from the appliance door when it is
open.
Cleaning and user maintenance shall not be made by children
without supervision.
GENERAL SAFETY
Do not change the specification of this appliance.
Obey the maximum load volume of 10 kg (refer to the
“Programme chart” chapter).
The operating water pressure (minimum and maximum) must be
between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa).
The ventilation openings in the base (if applicable) must not be
obstructed by a carpet.
The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
2
Before maintenance, deactivate the appliance and disconnect
the mains plug from the mains socket.
Do not use water spray and steam to clean the appliance.
Clean the appliance with a moist soft cloth. Only use neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
Remove all the packaging and the transit bolts.
Keep the transit bolts. When you move the
appliance again you must block the drum.
Always be careful when you move the appliance
because it is heavy. Always wear safety gloves.
Do not install or use a damaged appliance.
Obey the installation instruction supplied with
the appliance.
Do not install or use the appliance where the
temperature is less than 0 °C or where it is
exposed to the weather.
Make sure that the floor where you install the
appliance is flat, stable, heat resistant and clean.
Make sure that there is air circulation between
the appliance and the floor.
Adjust the feet to have the necessary space
between the appliance and the carpet.
Do not install the appliance where the appliance
door can not be fully opened.
ELECTRICAL CONNECTION
The appliance must be earthed.
Always use a correctly installed shockproof
socket.
Make sure that the electrical information on the
rating plate agrees with the power supply. If not,
contact an electrician.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not touch the mains cable or the mains plug
with wet hands.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Only for UK and Ireland. The appliance has a 13
A mains plug. If it is necessary to change the
fuse in the mains plug, use a 13 A ASTA (BS
1362) fuse.
This appliance complies with the E.E.C.
Directives.
WATER CONNECTION
Make sure not to cause damage to the water
hoses.
Before you connect the appliance to new pipes
or pipes not used for a long time, let the water
flow until it is clean.
The first time you use the appliance, make sure
that there is no leakage.
USE
WARNING! Risk of injury, electrical
shock, fire, burns or damage to the
appliance.
Use this appliance in a household only.
Obey the safety instructions on the detergent
packaging.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Make sure that you remove all metal objects
from the laundry.
Do not put a container to collect possible water
leakage under the appliance. Contact the
Authorised Service Centre to ensure which
accessories can be used.
Do not touch the glass of the door while a
programme operates. The glass can be hot.
SERVICE
To repair the appliance contact an Authorised
Service Centre.
Use original spare parts only.
DISPOSAL
WARNING! Risk of injury or
suffocation.
3
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
Remove the door catch to prevent children and
pets to get closed in the appliance.
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1 2 3
5
6
4
1
Worktop
2
Detergent dispenser
3
Control panel
4
Door handle
5
Rating plate
6
Feet for the appliance level
4
EASY START
CONTROL PANEL DESCRIPTION
Kurz / Rapide
Fertig um
Fini à
Temp.
Schleudern
Essorage
Optionen
Options
Intensiv / Intensif
Mix / Mixtes
Koch-/Buntwäsche / Coton
Koch-/Buntwäsche / Coton
ECO
Pflegeleicht / Synthétiques
Feinwäsche / Délicats
Wolle / Laine
Auffrischen 20 min / Rafraîchir 20'
Ein/Aus
Marche/Arrêt
Bügelquick /
Anti-froissage
Spülen / Rinçage
Pumpen / Vidange
Schleudern /
Essorage
6
7
81 2 3 4 5
1
On / Off button
(Ein/Aus Marche/Arrêt)
2
Programme selection touchpad
3
Temperature touchpad
4
Spin selection touchpad
5
Finish at touchpad
(Fertig um/Fini à)
6
Start/Pause touchpad
7
Options selection touchpad
8
Display
DISPLAY
A B C E
FG
D
A. The Temperature area:
: Temperature indicator
5
: Cold water indicator
B. : The permanent extra rinse indicator
C. The spin area:
: The spin speed indicator
: The No Spin indicator
: The Rinse Hold indicator
: The Extra Silent indicator
D. The time area:
: The programme duration
: The time of cycle finish (when the
is selected) or the current time
1)
: The alarm codes
: The message of error
: Programme is completed.
E. : The door locked indicator
You cannot open the appliance door when
the symbol is on.
You can open the door only when the
symbol goes off.
F.
: The Finish At indicator (Fertig um/Fini à)
G. : The indicator of the child lock
PROGRAMME CHART
Programme
Temperature range
Maximum load
Maximum spin
speed
Programme description
(Type of load and soil level)
30' @ 30°
30°C
3 kg
800 rpm
A short cycle for synthetic and delicate items with
light soil level or for items to freshen up.
Koch-/Buntwä-
sche/Coton
90°C - Cold
10 kg
1400 rpm
White cotton and coloured cotton. Normal soil and
light soil.
Koch-/Bunt-
wäsche/Coton
ECO
1)
60°C - 40°C
10 kg
1400 rpm
White cotton and colour-fast cotton. Normal soil. The
energy consumption decreases and the time of the wash-
ing programme is extended.
Pflegeleicht/
Synthétiques
60°C - Cold
4 kg
1200 rpm
Synthetic items or mixed fabric items. Normal soil.
Feinwäsche/Déli-
cats
40°C - Cold
4 kg
1200 rpm
Delicate fabrics such as acrylics, viscose, polyester
items. Normal soil.
Wolle/Laine
40°C - Cold
1,5 kg
1200 rpm
Machine washable wool, hand washable wool and
delicate fabrics with «hand washing» care symbol.
2)
Auffrischen 20
min/Rafraîchir 20'
40°C - 30°C
1 kg
1200 rpm
A very short cycle for cotton and synthetic items with
light soil level or worn only once.
1) Visible only for 2 seconds when you activate the appliance.
6
Programme
Temperature range
Maximum load
Maximum spin
speed
Programme description
(Type of load and soil level)
Mix/Mixtes
60°C - Cold
2 kg
1200 rpm
Special programme for cotton, synthetic and mixed
fabrics with light soil. In case of setting cold wash cycle
make sure to use the detergent designed for low tempera-
tures.
1) Standard programmes for the Energy Label consumption values. According to regulation
1061/2010, these programmes are respectively the «Standard 60 °C cotton programme» and the «Stand-
ard 40 °C cotton programme». They are the most efficient programmes in terms of combined energy and
water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the
selected programme.
2) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
Programme options compatibility
Programme
Kurz/Rapide
1)
Intensiev/Intensif
Bügelquick/Anti-froissage
Spülen/Rinçage
Pumpen Schleudern/Vidange Essorage
30' @ 30° ŶŶ ŶŶŶ
Koch-/
Buntwä-
sche/Coton
ŶŶ Ŷ Ŷ Ŷ Ŷ Ŷ Ŷ Ŷ Ŷ Ŷ
Koch-/
Buntwä-
sche/Coton
ECO
ŶŶ Ŷ Ŷ Ŷ ŶŶŶŶ
7
Programme
Kurz/Rapide
1)
Intensiev/Intensif
Bügelquick/Anti-froissage
Spülen/Rinçage
Pumpen Schleudern/Vidange Essorage
Pflege-
leicht/
Synthé-
tiques
ŶŶ Ŷ Ŷ Ŷ Ŷ Ŷ Ŷ Ŷ Ŷ Ŷ
Feinwä-
sche/Déli-
cats
ŶŶ Ŷ Ŷ Ŷ Ŷ ŶŶŶŶ
Wolle/Laine ŶŶ Ŷ Ŷ ŶŶŶ
Auffrischen
20 min/
Rafraîchir
20'
ŶŶ Ŷ ŶŶŶ
Mix/Mixtes ŶŶ Ŷ ŶŶŶŶ ŶŶŶ
1) When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to
keep the full load but the washing results can be unsatisfactory. Recommended load: cotton: 5 kg, syn-
thetics and delicates: 2,5 kg.
CONSUMPTION VALUES
The data in this table are approximate. Different variables can affect the data: the quantity
and type of laundry, the water and ambient temperature.
8
At the start of the programme, the display shows the programme duration for the maxi-
mum load capacity.
During the washing phase the programme duration is automatically calculated and can be
greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton
60°C, maximum load capacity 10 kg, the programme duration exceeds 2 hours; actual
load 1 kg, the programme duration will be less than 1 hour).
When the appliance is calculating the real programme duration a dot flashes in the dis-
play.
Programmes Load (kg)
Energy con-
sumption
(kWh)
Water con-
sumption (li-
tre)
Approximate
programme
duration (mi-
nutes)
Remaining
moisture (%)
1)
Koch-/Buntwäsche/
Coton 60°C
10 2,04 87 240 52
Koch-/Buntwäsche/
Coton 40°C
10 1,40 83 210 52
Pflegeleicht/Synthé-
tiques 40°C
4 0,80 61 140 35
Feinwäsche/Délicats
40°C
4 0,56 75 95 35
Wolle/Laine 30°C
2)
1,5 0,42 62 75 30
Standard cotton programmes
Standard 60°C cot-
ton
10 1,02 57 252 52
Standard 60°C cot-
ton
5 0,75 46 205 52
Standard 40°C cot-
ton
5 0,67 46 205 52
1) At the end of spin phase.
2) Not available for some models.
Off Mode (W) Left On Mode (W)
0.48 0.48
The information given in the chart above is compliant with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC.
9
OPTIONS
TEMPERATURE
With this option you can change the default
temperature.
Indicator
= cold water.
The indicator of the set temperature comes on.
SCHLEUDEM/ESSORAGE
With this option you can decrease the default spin
speed.
The display shows the indicator of the set speed.
Additional spin options:
No Spin
Set this option to remove all spin phases.
Set it for very delicate fabrics.
The rinse phase uses more water for some
washing programmes.
The display shows the indicator
.
Rinse Hold
Set this option to prevent the laundry creases.
The washing programme stops with the water in
the drum. The drum turns regularly to prevent
the laundry creases.
The door stays locked. You must drain the water
to unlock the door.
The display shows the indicator
.
To drain the water refer to ‘At the end
of the programme’.
Extra Silent
Set this option to remove all spin phases and to
perform a silent washing.
The rinse phase uses more water for some
washing programmes.
The washing programme stops with the water in
the drum. The drum turns regularly to prevent
the laundry creases.
The door stays locked. You must drain the water
to unlock the door.
The display shows the indicator
.
To drain the water refer to ‘At the end
of the programme’.
KURZ/RAPIDE
With this option you can decrease the programme
duration.
Use this option for items with light soil or items to
refresh.
The related indicator comes on.
INTENSIEV/INTENSIF
With this option you can wash very soiled laundry.
The washing cycle lasts longer with this option.
The related indicator comes on.
BÜGELQUICK/ANTI-FROISSAGE
The appliance carefully washes and spins the
laundry to prevent the creases.
The appliance decreases the spin speed, uses
more water and adapts the programme duration to
the type of laundry.
The related indicator comes on.
SPÜLEN/RINÇAGE
With this option you can perform only a last rinse of
a selected washing programme.
If you set also the Extra Rinse function (
) the
appliance adds two or more rinses.
The related indicator comes on.
PUMPEN SCHLEUDERN/VIDANGE
ESSORAGE
With this option you can perform the spin and drain
cycle.
The spin phase is suitable to the washing
programme you set.
If you set also the No Spin option
( ) , the appliance only drains.
FERTIG UM/FINI À
With this option you can set the exact time in which
you would like your washing programme to be
completed.
The start of the washing programme delays. The
washing programme finishes in the set hour.
You can set the end time to 20 hours forward at
maximum.
The display shows the set hour of cycle's finish and
the indicator
comes on.
EXTRA RINSE
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to detergents
and in areas where the water is soft.
The related indicator comes on.
1)
10
1) See in "Settings" how to activate this option.
SETTINGS
PERMANENT EXTRA RINSE
With this option you can permanently have an extra
rinse when you set a new programme.
To activate/deactivate this option touch the
buttons
and at the same time until the
indicator comes on/goes off.
CHILD LOCK
With this option you can prevent that the children
play with the control panel.
To activate/deactivate this option, touch the
buttons
and at the same time until the
indicator comes on/goes off.
Activate this option after you touch the button
:
the buttons are locked (except for the button ) .
This option stays active even when you
switch off the appliance.
ACOUSTIC SIGNALS
The acoustic signals operate when:
The programme is completed.
The appliance has a malfunction.
To deactivate/activate the acoustic signals,
touch the buttons
and at the same time for 4
seconds.
If you deactivate the acoustic signals,
they continue operate when the
appliance has a malfunction.
BEFORE FIRST USE
WARNING! Refer to Safety chapters.
BEFORE FIRST USE
1. Put a small quantity of detergent in the
compartment for washing phase.
2. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and the
tub.
CLOCK SETTING
1. Touch the button
and the button at the
same time for some seconds.
The hour digits flash.
2. Touch the button
to change (or confirm) the
hour. The hours change with the steps of one
hour.
1)
3. Touch the button to confirm the selection.
The minute digits flash.
4. Touch the button
to change (or confirm) the
minutes. The minutes change with the steps of
one minute.
1)
5. Touch the button to confirm the selection.
The appliance enters automatically in
clock setting mode when:
you activate the appliance for the first time after
the installation,
you activate the appliance for the first time after
it has been unplugged for more than two weeks,
you did not confirm the time selection within 15
seconds period from last button touching,
you switched the appliance off before
confirming the time.
DAILY USE
WARNING! Refer to Safety chapters.
1) See in "Settings" how to activate this option.
1) If you keep the button
pressed the digits change in a quicker way.
11
g
1) If you keep the button pressed the digits change in a quicker way.
11
LOADING THE LAUNDRY
Open the water tap. Connect the mains plug to the
mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the drum.
Refer to max. loads indicated in "Programme chart".
4. Close the door.
CAUTION!
Make sure
that no laun-
dry stays be-
tween the
seal and the
door. There
is a risk of
water leak-
age or dam-
age to the
laundry.
USING DETERGENT AND ADDITIVES
1. Measure out the de-
tergent and the fabric
conditioner.
2. Put the detergent
and the fabric condi-
tioner into the com-
partments.
3. Carefully close the
detergent drawer.
DETERGENT COMPARTMENTS
Detergent compartment for
washing phase.
If you use liquid detergent, put it
immediately before you start the
programme.
Compartment for liquid additives
(fabric conditioner, starch).
CAUTION! Do not
exceed the MAX
level.
Flap for powder or liquid deter-
gent.
LIQUID OR POWDER DETERGENT
A
The default position of
the flap is A (powder de-
tergent).
To use liquid detergent:
1. Remove the drawer.
Push the drawer edge in
the place with the arrow
(PUSH) to remove the
drawer easily.
B
2. Adjust the flap in posi-
tion B.
3. Put back the drawer in
the recess.
When you use the liquid detergent:
Do not use gelatinous or thick liq-
uid detergents.
Do not put more liquid then 120
ml.
Do not set the delay start.
A
When the flap is in posi-
tion B and you want to
use powder detergent:
1. Remove the drawer.
2. Adjust the flap in po-
sition A.
3. Put back the drawer
in the recess.
Measure out the detergent and the fabric condi-
tioner.
Put the detergent and the fabric conditioner into
the compartments.
Carefully close the detergent drawer.
ACTIVATING THE APPLIANCE
Press and hold for a couple of seconds the
button to activate or deactivate the appliance.
12
A tune sounds when the appliance is activated. The
appliance performs a start up animation. The
animation quickly shows each washing programme
and the default temperature and spin settings.
The display shows the word On.
SETTING A PROGRAMME
1. Touch the programme button
and set the
programme:
The indicator of the button
flashes.
The display shows the programme duration.
2. If necessary, change the temperature and the
spin speed or add available options. When you
activate an option, the indicator of the set
option comes on.
If you set something incorrect, the
display shows the message .
STARTING A PROGRAMME WITHOUT THE
FERTIG UM/FINI À OPTION
Touch the button
.
The indicator of the button
stops to
flash and stays on.
The programme starts, the door locks, the
indicator is on.
The drain pump can operate for a short time
at the beginning of the washing cycle.
After approximately 15 minutes from
the start of the programme:
The appliance adjusts automatically
the programme duration agree with
the laundry load.
The display shows the new value.
STARTING A PROGRAMME WITH THE
FERTIG UM/FINI À OPTION
Check if the appliance has the correct hour set.
See in "Clock setting" how to set the appliances's
clock.
First set the programme (and add options) then set
the option
.
1. Touch the button
to set the desired end
time. With the first touch the time is rounded to
the nearest hour or to the nearest half an hour.
By each next touch the end time increases by
30 minutes segments until maximum range of
20 hours.
1)
The display shows the finish hour you set (e.g.
) and the indicator is on to show that
this option is active.
2. Touch the button :
The door is locked.
The appliance starts the countdown.
When the countdown is completed, the
programme starts automatically and the
actual programme duration counts down in
minutes until the cycle end.
You can cancel or change the set of
the option before you touch the
button . After touching the button
you can only cancel the option .
To cancel the Fertig um/Fini à
option:
a. Touch the button to set the appliance
to pause. The indicator of button
flashes.
b. Touch the button again and again until
the indicator
goes off from the display.
Touch the button again to start the
programme immediately.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before they
operate.
1. Touch
.
The indicator of this button flashes.
2. Change the options.
If you change any option the option (if set)
will be disabled.
3. Touch again.
The programme continues.
CANCELLING A PROGRAMME
1. Press the button for some seconds to
cancel the programme and to deactivate the
appliance.
2. Press the same button again to activate the
appliance. Now, you can set a new washing
programme.
1) If you keep the button pressed the digits change in a quicker way.
13
Before starting the new programme
the appliance could drain the water. In
this case, make sure that the detergent
is still in the detergent compartment, if
not fill the detergent again.
OPENING THE DOOR
While a programme (or the
) operates, the
appliance door is locked. The indicator is on.
CAUTION! If the temperature and
level of the water in the drum are too
high, you cannot open the door.
To open the door during the first minutes of
the cycle (or when the
operates) :
1. Touch the button
to pause the appliance.
2. Wait until the indicator goes off.
3. You can open the door.
4. Close the door and touch the button again.
The programme (or the ) continues.
AT THE END OF THE PROGRAMME
The appliance stops automatically.
The acoustic signal operates (if it is activated).
In the display
comes on.
The indicator of the button goes off.
The door lock indicator goes off.
You can open the door.
Remove the laundry from the appliance. Make
sure that the drum is empty.
Press the button for some seconds to
deactivate the appliance.
Close the water tap.
Keep the door and the detergent drawer ajar, to
prevent the mildew and odours.
The washing programme is completed, but
there is water in the drum:
The drum turns regularly to prevent the creases
in the laundry.
The indicator
flashes to remind you to drain
the water.
The door lock indicator
is on. The indicator
of button flashes. The door stays locked.
You must drain the water to open the door.
Draining the water:
1. To drain the water.
Touch the button
. The appliance
drains the water and spins with the
maximum spin speed for selected washing
programme.
Alternatively, touch the button to change
the spin speed and then touch the button
. The appliance drains the water and
spins. If you set
, the appliance only
drains.
2. When the programme is completed and the
door lock indicator goes off, you can open
the door.
3. Press the button for some seconds to
deactivate the appliance.
The appliance drains and spins
automatically after approximately 18
hours (except for Wool programme).
AUTO-OFF OPTION
The AUTO-OFF stand-by option automatically
deactivates the appliance to decrease the energy
consumption. All the indicators and the display go
off when :
You do not use the appliance for 5 minutes
before you touch
.
Press the button to activate the appliance
again.
After 5 minutes from the end of the washing
programme.
Press the button to activate the appliance
again.
The display shows the end of the last set
programme.
Touch the button
if you want to set a new
cycle.
HINTS AND TIPS
THE LAUNDRY LOAD
Divide the laundry in: white, coloured,
synthetics, delicates and wool.
Obey the washing instructions that are on the
laundry care labels.
Do not wash white and coloured items together.
14
Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first times.
Button up pillowcases, close zippers, hooks and
poppers. Tie up belts.
Empty the pockets and unfold the items.
Turn multilayered fabrics, wool and items with
painted illustrations inside out.
Remove hard stains.
Wash heavy soil stains with a special detergent.
Be careful with the curtains. Remove the hooks
or put the curtains in a washing bag or
pillowcase.
Do not wash laundry without hems or with cuts.
Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, etc. ).
A very small load can cause balance problems
with the spin phase. If this occurs, adjust
manually the items in the tub and start the spin
phase again.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENTS AND ADDITIVES
Only use detergents and additives specially
made for washing machines:
powder detergents for all types of fabric,
powder detergents for delicate fabrics (40
°C max) and woollens,
liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special for woollens
only.
Do not mix different types of detergents.
To help the environment, do not use more than
the correct quantity of detergent.
Obey the instructions that you find on the on
packaging of these products.
Use the correct products for the type and colour
of the fabric, the programme temperature and
the level of soil.
If your appliance does not have the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by the
detergent's manufacturer).
ECOLOGICAL HINTS
Set a programme without the prewash phase to
wash laundry with normal soil.
Always start a washing programme with the
maximum load of laundry allowed.
If necessary, use a stain remover when you set a
programme with a low temperature.
To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To know the water hardness in your area, contact
your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
CARE AND CLEANING
WARNING! Refer to Safety chapters.
EXTERNAL CLEANING
Clean the appliance only with soap and warm
water. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
DESCALING
If the water hardness in your area is high or
moderate, we recommend that you use a water
descaling product for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special products
for washing machines. Do this separately from the
laundry wash.
Always obey the instructions that you
find on the packaging of the product.
15
MAINTENANCE WASH
With the low temperature programmes it is possible
that some detergent stays in the drum. Perform a
maintenance wash regularly. To do this:
Remove the laundry from the drum.
Set the cotton programme with the highest
temperature with a small quantity of detergent.
DOOR SEAL
Regularly examine the
seal and remove all ob-
jects from the inner part.
CLEANING THE DETERGENT DISPENSER
1 2 3 4
5 6
CLEANING THE INLET HOSE AND THE VALVE FILTER
1
2
3
1 2 3
45°
20°
4
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can be less than 0 °C, remove the
remaining water from the inlet hose and the drain
pump.
Do this procedure also when you want
to do the emergency drain.
1. Disconnect the mains plug from the mains
socket.
2. Remove the water inlet hose.
3. Remove the drain hose from the rear support
and unhook it from sink or spigot.
4. Put the ends of the drain and inlet hose in a
container. Let the water flow out of the hoses.
16
5. When no more water flows, install the inlet
hose and the drain hose again.
WARNING! Make sure that the
temperature is more than 0 °C before
you use the appliance again. The
manufacturer is not responsible for
damages caused by low temperatures.
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
The appliance does not start or it stops during
operation.
First try to find a solution to the problem (refer to
the table). If the problem persists, contact the
Authorised Service Centre.
With some problems, the acoustic signals
operate and the display shows an alarm
code:
- The appliance does not fill with water
properly.
- The appliance does not drain the water.
- The appliance door is open or not
closed correctly. Please check the door!
If the appliance is overloaded,
remove some items from the drum
and/or keep pressed the door and
push the button at the same
time until the indicator stops
flashing (see the picture below).
- The mains supply is unstable. Wait until
the mains supply is stable.
- No communication between electronic
elements of the appliance. Switch off and
switch on again.
WARNING! Deactivate the appliance
before you do the checks.
POSSIBLE FAILURES
Problem Possible solution
The programme does not
start.
Make sure that the mains plug is connected to the mains socket.
Make sure that the appliance door is closed.
Make sure that there is not a damaged fuse in the fuse box.
Make sure that the Start/Pause has been pressed.
If the delay start is set, cancel the setting or wait for the end of
countdown.
Deactivate the Child Lock function if it is on.
17
Problem Possible solution
The appliance does not fill
with water properly.
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter of the inlet hose and the filter of the valve
are not clogged. Refer to “Care and cleaning”.
Make sure that the inlet hose has no kinks or bends.
Make sure that the connection of the water inlet hose is correct.
The appliance does not
drain the water.
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
Make sure that the connection of the drain hose is correct.
Set the drain option if you set a programme without drain phase.
Set the drain option if you set an option which ends with water in
the drum.
If above mentioned solutions do not help, contact the Authorised
Service Centre (as the filter of the drain pump may be clogged).
The spin phase does not
operate or the washing cy-
cle lasts longer than usual-
ly.
Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
Set the spin option.
Set the drain option if you set an option which ends with water in
the drum.
Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
If above mentioned solutions do not help, contact the Authorised
Service Centre (as the filter of the drain pump may be clogged).
There is water on the floor. Make sure that the couplings of the water hoses are tight and there
is not water leakages.
Make sure that the water inlet hose and the drain hose have no
damages.
Make sure you use the correct detergent and the correct quantity of
it.
You cannot open the appli-
ance door.
Make sure that the washing programme is finished.
Set the drain or the spin option if there is water in the drum.
Do the emergency drain procedure. See "Frost precautions" (in
"Care and Cleaning" chapter).
The appliance makes an
unusual noise.
Make sure the levelling of the appliance is correct. Refer to 'Installa-
tion instruction'.
Make sure that the packaging and/or the transit bolts are removed.
Refer to 'Installation instruction'.
Add more laundry in the drum. The load may be too small.
The appliance fills with wa-
ter and drain immediately.
Make sure that the drain hose is in the correct position. The end of
the hose may be too low. Refer to 'Installation instruction'.
The cycle is shorter than
the time displayed.
The appliance calculates a new time according to the laundry load.
See the ‘Consumption Values’ chapter.
The cycle is longer than
the time displayed.
An unbalanced laundry load increases the duration time. This is a
normal behaviour of the appliance.
18
Problem Possible solution
The washing results are
not satisfactory.
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you
wash the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
You cannot set an option. Make sure that you press only the wanted touch button(s).
After the check, activate the appliance. The
programme continues from the point of interruption.
If the problem occurs again, contact the Authorised
Service Centre.
If the display shows other alarm codes. Deactivate
and activate the appliance. If the problem
continues, contact the Authorised Service Centre.
SERVICE
We recommend the use of original spare parts.
When contacting the Authorised Service Centre,
make sure that these data are available. You can
find the information on the rating plate: model, PNC
and Serial Number. (Mod., Prod. No., Ser. No.)
TECHNICAL DATA
Dimension Width/ Height/ Depth/ To-
tal depth
600 mm/ 850 mm/ 600 mm/ 660 mm
Electrical connection Voltage
Overall power
Fuse
Frequency
230 V
2200 W
10 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply pressure Minimum
Maximum
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Water supply
1) Cold water
Maximum Load Cotton 10 kg
Energy Efficiency Class A+++ -20%
Spin Speed Maximum 1400 rpm
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
19
CH
GUARANTEE
Customer Service Centres
Point of Service
Industriestrasse 10
5506 Mägenwil
Le Trési 6
1028 Préverenges
Via Violino 11
6928 Manno
Morgenstrasse 131
3018 Bern
Zürcherstrasse 204E
9000 St. Gallen
Seetalstrasse 11
6020 Emmenbrücke
St. Jakob-Turm Birsstrasse 320B
4052 Basel
Comercialstrasse 19
7000 Chur
Spare parts service Industriestrasse 10, 5506
Mägenwil, Tel. 0848 848 111
Specialist advice/Sale Badenerstrasse 587,
8048 Zürich, Tel. 044 405 81 11
Warranty For each product we provide a two-year
guarantee from the date of purchase or delivery to
the consumer (with a guarantee certificate, invoice
or sales receipt serving as proof). The guarantee
covers the costs of materials, labour and travel. The
guarantee will lapse if the operating instructions
and conditions of use are not adhered to, if the
product is incorrectly installed, or in the event of
damage caused by external influences, force
majeure, intervention by third parties or the use of
non-genuine components.
ENVIRONMENT CONCERNS
Recycle the materials with the symbol . Put the
packaging in applicable containers to recycle it.
Help protect the environment and human health
and to recycle waste of electrical and electronic
appliances. Do not dispose appliances marked with
the symbol
with the household waste. Return the
product to your local recycling facility or contact
your municipal office.
For Switzerland:
Where should you take your old
equipment?
Anywhere that sells new equipment or
hand it in to official SENS collection
points or official SENS recycling firms.
The list of official SENS collection
points can be found at
www.erecycling.ch
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Zanussi ZWF14010S Benutzerhandbuch

Kategorie
Waschmaschinen
Typ
Benutzerhandbuch

in anderen Sprachen